• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.11
• /
• pp.963-968
• /
• 2000

Magnetic properties and microstructures of Fe$\_$93-x/Zr$_3$B$_4$Ag$\_$x/ thin films were investigated as a function of addition of element Ag, (X$\_$Ag/=0 to 6 at.%) and annealing temperature, T$\_$a/=300$\^{C}$ to 600$\^{C}$. In the case of adding Ag, magnetic properties of Fe$\_$93-x/Zr$_3$B$_4$Ag$\_$x/ thin films were improved than those of Ag-free Fe$\_$93/Zr$_3$B$_4$thin films. The prominent soft magnetic properties with coercivity of 1.1 Oe, saturation magnetization of 2.2 T and permeability of 5400 at 50㎒ were obtained from Fe$\_$88/Zr$_3$B$_4$Ag$\_$5/ thin film annealed was lower than that of Fe-base or Co-base thin films reported previously. Such enhanced magnetic properties are presumably attributed to the format in ultra fine grains. Also, the reduced eddy current loss in the annealed sample is due to refined micro magnetic domains with increasing the amount of Ag in Fe$\_$93-x/Zr$_3$B$_4$Ag$\_$x/ thin films.

• Journal of Soil and Groundwater Environment
• /
• v.19 no.1
• /
• pp.63-69
• /
• 2014

This paper presents the feasibility of using different iron oxides (microscale hematite (HT), microscale magnetite (MT), and nanoscale maghemite (NMH)) in enhancing nitrate reduction by zero-valent iron (Fe(0)) under two solution conditions (artificial acidic water and real groundwater). Addition of MT and NMH into Fe(0) system resulted in enhancement of nitrate reduction compared to Fe(0) along reaction, especially in groundwater condition, while HT had little effect on nitrate reduction in both solutions. Field emission scanning electron microscopy (FESEM) analysis showed association of MT and NMH with Fe(0) surface, presumably due to magnetic attraction. The rate enhancement effect of the minerals is presumed to arise from its role as an electron mediator that facilitated electron transport from Fe(0) to nitrate. The greater enhancement of MT and NMH in groundwater was attributed to surface charge neutralization by calcium and magnesium ions in groundwater, which in turn facilitated adsorption of nitrate on Fe(0) surface.

• Bulletin of the Korean Chemical Society
• /
• v.16 no.6
• /
• pp.511-515
• /
• 1995

Since much studies have been performed concerning the electrochemical behaviors and the practical applications of PB based devices, little has yet reported to investigate the best condition for the preparation for PB thin films. As considered some factors(peak shape, peak current, and peak separation) from the i-V curves, the optimal condition in the film growth were investigated under various immersion solutions. An electron-transfer processes of Fe2+/Fe3+ and Fe(CN)63-/4- redox couples were considered by measuring the observed currents as a function of the rotation velocity. The standard heterogeneous electron-transfer rates for these films and bare Au disc electrode in 10-3 M Fe2+/Fe3+ solution, applied at +0.65 V vs. SCE, were 6.14 × 10-3 and 7.78 × 10-3 cm/s, respectively, obtained using a rotating disc electrode. In case of the addition of potassium ion, the rate constants for these Fe2+/Fe3+ system on thin films of PB and bare electrode were given a little high values. The electron transfer rate for 10-3 M Fe(CN)63-/4- were 4.55 × 10-3 and 6.84 × 10-3 cm/s, respectively. The conductivity as directly determined during obtained the voltammogram, was 2.2 × 10-7 (Ω·cm)-1. This value is similar magnitude to that calculated from bulk sample.

• Journal of the Korean institute of surface engineering
• /
• v.52 no.4
• /
• pp.233-238
• /
• 2019

The formation behavior of zinc phosphate conversion coating (ZPCC) on SCM430 alloy was investigated in 25 vol.% of 1M ZnO + 170 ml/L solution containing various $Fe(NO_3)_2$ concentrations, using open-circuit potential(OCP), electrochemical impedance spectroscopy(EIS), cyclic polarization(CP) curve and tape peel test. OCP of SCM430 alloy and corrosion current density increased with increasing $Fe(NO_3)_3$ concentration. Resistance of films formed on SCM430 alloy by chemical conversion treatment decreased with increasing $Fe(NO_3)_3$ concentration. Color and adhesion of chemical conversion coatings became darker and worse, respectively, with increasing $Fe(NO_3)_3$ concentration. It is concluded that addition of $Fe(NO_3)_3$ into a zinc phosphating bath leads to faster reaction to form porous surface coatings with poor adhesion and corrosion resistance.

• Korean Journal of Materials Research
• /
• v.33 no.9
• /
• pp.353-359
• /
• 2023

This study investigated the growth behavior and characteristics of compounds formed at the interface between a liquid Al-Si-Cu alloy and solid cast iron. Through microstructural analyses, it was observed that various AlFe and AlFeSi phases are formed at the interface, and the relative proportion of each phase changes when small amounts of strontium are added to the Al alloy. The results of the microstructural analysis indicate that the primary phases of the interfacial compounds in the Al-Si-Cu base alloy are Al₈Fe₂Si and Al_4.5FeSi. However, in the Sr-added alloys, significant amounts of binary AlFe intermetallic compounds such as Al₅Fe₂ and Al₁₃Fe₄ formed, in addition to the AlFeSi phases. The inclusion of Sr has a slight diminishing effect on the rate at which the interfacial compounds layer thickens during the time the liquid Al alloy is in contact with the cast iron. The study also discusses the nano-indentation hardness and micro-hardness of the interfacial phases.

• Journal of Nutrition and Health
• /
• v.37 no.8
• /
• pp.645-654
• /
• 2004

This study examined the effect of excess calcium (Ca) on the iron (Fe) bioavailability and bone growth of marginally Fe deficient animals. Two groups of weanling female SD rats were fed either normal Fe (35 ppm) or Fe deficient diet (8 ppm) for 3 weeks. Then each group of animals were assigned randomly to one of three groups and were fed one of six experimental diets additionally for 4 weeks, containing normal (35 ppm) or low (15 ppm) Fe and one of three levels of Ca as normal (0.5%), high (1.0%), or excess (1.5%). Feces and urine were collected during the last 3 days of treatment. After sacrifice blood, organs, and femur bone were collected for analysis. Final body weight and average food intake were not affected by either the levels of dietary Ca or Fe. Low Fe diet significantly reduced the level of serum ferritin, however, for Hb, Hct, and TIBC no difference was shown than those in the normal Fe group. TIBC increased slightly by high and excess Ca intake in low Fe groups. For both normal and low Fe groups, high and excess Ca intakes reduced the apparent absorption of Fe and Fe contents of liver significantly (p < 0.05). Calcium contents in kidney and Femur of rats that were fed high and excess levels of Ca were significantly greater than those of normal Ca groups. However, weight, length, and breaking force of the bone were not affected by increased Ca intakes. Both in control and low Fe groups, high and excess intakes of Ca decreased the apparent absorption of Ca. These results indicate that the excess intakes of calcium than the normal needs would be undesirable for Fe bioavailability and that the adverse effects be more serious in marginally iron deficient growing animals. In addition bone growth and strength would not be favorably affected by high Ca intakes, though, the long term effect of increased Ca contents in bone requires further examination.

• Journal of Powder Materials
• /
• v.30 no.2
• /
• pp.101-106
• /
• 2023

Liquid metal extraction (LME), a pyrometallurgical recycling method, is popular owing to its negligible environmental impact. LME mainly targets rare-earth permanent magnets having several rare-earth elements. Mg is used as a solvent metal for LME because of its selective and eminent reactivity with rare-earth elements in magnets. Several studies concerning the formation of Dy-Fe intermetallic compounds and their effects on LME using Mg exist. However, methods for reducing these compounds are unavailable. Fe reacts more strongly with B than with Dy; B addition can be a reducing method for Dy-Fe intermetallic compounds owing to the formation of Fe₂B, which takes Fe from Dy-Fe intermetallic compounds. The FeB alloy is an adequate additive for the decomposition of Fe₂B. To accomplish the former process, Mg must convey B to a permanent magnet during the decomposition of the FeB alloy. Here, the effect of Mg on the transfer of B from FeB to permanent magnet is observed through microstructural and phase analyses. Through microstructural and phase analysis, it is confirmed that FeB is converted to Fe₂B upon B transfer, owing to Mg. Finally, the transfer effect of Mg is confirmed, and the possibility of reducing Dy-Fe intermetallic compounds during LME is suggested.

• Journal of the Korean Ceramic Society
• /
• v.43 no.2 s.285
• /
• pp.131-135
• /
• 2006

In this study, the dielectric, magnetic and transport properties of $Gd_{0.33}Sr_{0.67}FeO_3$ have been analyzed. The dielectric loss anomaly was found to be around 170 K. The activation energy corresponding to relaxation process of this dielectric anomaly was 0.17 eV. From the temperature dependence of the characteristic frequency, we concluded that the elementary process of the dielectric relaxation peak observed is correlated with polaron hopping between $Fe^{3+}\;and\;Fe^{4+}$ ions. The electrical resistivity displayed thermally activated temperature dependence above 200 K with an activation energy of 0.16 eV. In addition, the temperature dependence of thermoelectric power and resistivity suggests that the charge carrier responsible for conduction is strongly localized.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.2
• /
• pp.292-298
• /
• 1998

${\alpha}-Fe_2O_3$films were prepared by a dip-coating method using the mixed solution of ferric nitrate, ethylene glycol and acethyl acetone. The polymerization effect of the mixed solution was studied by FT-IR spectroscopic analysis, and the decomposition of organic parts and crystallization of the dip-coated film were investigated by FT-IR, XRD and DSC. In addition, AFM and SEM were employed to analyze the surface roughness and the thickness of ${\alpha}-Fe_2O_3$films.

• Computers and Concrete
• /
• v.25 no.5
• /
• pp.461-470
• /
• 2020

This paper presents a numerical study on structural behavior of hammer head pier cap beams, extended on verges and reinforced with carbon fiber reinforced polymer (CFRP) plates. A 3-D finite element (FE) model along with a simplified analytical model are presented. Concrete damage plasticity (CDP) was adapted in the FE model and an analytical approach predicting the CFRP anchor strength was adapted in both FE and analytical model. Total five quarter-scaled pier cap beams with various CFRP reinforcing schemes were experimentally tested and analyzed with numerical approaches. Comparison between experimental results, FE results, analytical results and current ACI guideline predictions was presented. The FE results showed good agreement with experimental results in terms of failure mode, ultimate capacity, load-displacement response and strain distribution. In addition, the proposed strut-and-tie based analytical model provides the most accurate prediction of ultimate strength of extended cap beams among the three numerical approaches.