• International Journal of Precision Engineering and Manufacturing
• /
• v.3 no.1
• /
• pp.5-12
• /
• 2002

The grinding process has been mainly used fur finishing metal products as final machining stage. But chatter vibration and bum of a workpiece have a bad effect on the machined surface and should be detected in modern grinding process. This paper deals with a fault detection of the cylindrical plunge grinding process by power parameters. During the grinding process the power signals of an induced motor were sampled and used to determine the relationship between fault and change of power parameters. A neural network was used far detecting the grinding fault and an influence of power parameters to the grinding fault was analyzed.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.12
• /
• pp.1090-1095
• /
• 2012

In this paper, we propose a model-based fault diagnosis method applied to vibration data. The fault detection is performed by comparing estimated parameters with normal parameters and deciding if the observed changes can be explained satisfactorily in terms of noise or undermodelling. The key feature of this method is that it accounts for the effects of noise and model mismatch. And we aslo design a classifier for the fault isolation by applying the multiclass SVM (Support Vector Machine) to the estimated parameters. The proposed fault detection and isolation methods are applied to an engine vibration data to show a good performance. The proposed fault detection method is compared with a signal-based fault detection method through a performance analysis.

• Journal of the Korean Society of Safety
• /
• v.34 no.4
• /
• pp.59-67
• /
• 2019

Since it is really hard to construct process models based on prior process knowledges, various statistical approaches have been employed to build fault diagnosis models. However, the crucial drawback of these approaches is that the solutions may vary according to the fault magnitude, even if the same fault occurs. In this study, the parameter monitoring approach is suggested. When a fault occurs in a chemical process, this leads to trigger the change of a process model and the monitoring parameters of process models is able to provide the efficient fault diagnosis model. A few important variables are selected and their predictive models are constructed by partial least square (PLS) method. The Euclidean norms of parameters of PLS models are estimated and a fault diagnosis can be performed as comparing with parameters of PLS models based on normal operational conditions. To improve the monitoring performance, cumulative summation (CUSUM) control chart is employed and the changes of model parameters are recorded to identify the type of an unknown fault. To verify the efficacy of the proposed model, Tennessee Eastman (TE) process is tested and this model can be easily applied to other complex processes.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.6
• /
• pp.31-38
• /
• 2012

Rotor of rotating machinery is the highly damaged part. Fault of 7 different types was confirmed as the main causes of rotor damage from the pump failure history data in domestic and U.S. nuclear. For each fault types, simulation testing was performed and fault signals were collected form the sensors. To calculate the statistical parameters of time-domain & frequency-domain, measured signals were analyzed by using the discrete wavelet transform, fast fourier transform, statistical analysis. Total 84 parameters were obtained. And Effectiveness factor were used to evaluate the discrimination capacity of each parameter. From the effectiveness factor, RAW-P4/RAW-P7/WT2-NNL/WT2-EE/WT1-P1 showed high ranking. Finally, these parameters were selected as the feature parameters of intelligent fault diagnostics for rotor.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.275-275
• /
• 2022

Tsunamis triggered by undersea earthquakes have the characteristic of longer wavelengths and can propagate a very long distance. Although the occurrence frequency of tsunami is low, it can cause casualties and properties. Historically, tsunamis that occurred on the western coast of Japan attacked the eastern coast of the Korean Peninsula and damaged the property and the loss of human life in 1983 and 1993. By tsunami in 1983 especially, 2 people were killed, and more than 200 casualties occurred. In addition, it caused 2 million dollars in property damage at Imwon Port. In 2011, The eastern cities of Japan: Iwate, Miyagi, Ibaraki, and Fukushima were damaged by a tsunami that occurred near onshore along the Pacific ocean and caused more than 300 billion dollars in property damage, and 20,000 casualties occurred. Moreover, those provoked nuclear power plant meltdown at Fukushima. In this study, it was carried out a relationship between maximum tsunami heights and fault parameters of earthquake: strike angle, dip angle, and slip angle at Imwon port. Those fault parameters are known that it does not relate to the magnitude of earthquake directly. Virtual tsunamis, which could be triggered by probable undersea earthquakes in the future, were investigated and mutual information based on probability and information theory was introduced to figure out the relationship between maximum tsunami height and fault parameters. Fault parameters were evaluated according to the strong relationship with maximum tsunami heights finally.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.1
• /
• pp.68-79
• /
• 1998

In this paper, we propose a model-based FDI(fault detetion and isolation) algorithm to detect and isolate fault in a linear system. The proposed algorithm is gased on an HFC(hydrid fault classifier) which consists of an FCART2(fault classifier by ART2 neural network) and an FCFM(fault classifier by fault models) which operate in parallel to isolate faults. The proposed algorithm is functionally composed of three main parts-parameter estimation, fault detection, and isolation. When a change in the system occurs, the estimated parameters go through a transition zone in which errors between the system output and the stimated output and the estimated output cross a predetermined thrseshold, and in this zone the estimated parameters are tranferred to the FCART2 for fault isolation. On the other hand, once a fault in the system is detected, the FCFM statistically isolates the fault by using the error between ach fault model out put and the system output. From the computer simulation resutls, it is verified that the proposed model-based FDI algorithm can be performed successfully to detect and isolate faults in a position control system of a DC motor.

• Earthquakes and Structures
• /
• v.12 no.3
• /
• pp.321-332
• /
• 2017

The reverse fault is a dangerous geological hazard faced by buried steel pipelines. Permanent ground deformation along the fault trace will induce large compressive strain leading to buckling failure of the pipe. A hybrid pipe-shell element based numerical model programed by INP code supported by ABAQUS solver was proposed in this study to explore the strain performance of buried X80 steel pipeline under reverse fault displacement. Accuracy of the numerical model was validated by previous full scale experimental results. Based on this model, parametric analysis was conducted to study the effects of four main kinds of parameters, e.g., pipe parameters, fault parameters, load parameter and soil property parameters, on the strain demand. Based on 2340 peak strain results of various combinations of design parameters, a semi-empirical model for strain demand prediction of X80 pipeline at reverse fault crossings was proposed. In general, reverse faults encountered by pipelines are involved in 3D oblique reverse faults, which can be considered as a combination of reverse fault and strike-slip fault. So a compressive strain demand estimation procedure for X80 pipeline crossing oblique-reverse faults was proposed by combining the presented semi-empirical model and the previous one for compression strike-slip fault (Liu 2016). Accuracy and efficiency of this proposed method was validated by fifteen design cases faced by the Second West to East Gas pipeline. The proposed method can be directly applied to the strain based design of X80 steel pipeline crossing oblique-reverse faults, with much higher efficiency than common numerical models.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2000.10a
• /
• pp.33-40
• /
• 2000

The assessment of earthquake hazards involved consideration of earthquake magnitude, frequency, last movement and probability of occurrence. The appraisal of earthquake potential is feasible because historical data show a good correlation between earthquake size and the fault rupture parameters of length, displacement, and area. Additionally, the characteristics of fault behavior should be considered to evaluate the earthquake potential magnitude. In this study, in order to evaluate the earth quake potential by the fault behavioral patterns, based on the experimental background which the geometric characteristics of the individual domains, such as strike, width, fault tip patterns, and orientation of secondary shears reflect sliding behavioral patterns in each section, the straight sections of A, D and E domains were examined to the creeping section of stably sliding. In contrast, the curved section of B domain was examined to the locked section of stick-slip movement. These results of studies can be applied to evaluate the earthquake potential magnitude from the fault structural parameters.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.224-228
• /
• 2003

The basic Principles and methods of the on-line monitoring of tribology parameters (friction coefficient and wear allowance) and fault diagnosis for the hoist disc brake system were introduced, the method were based on the spring force and oil pressure of the brake system and the hoist kinematics parameters. The experiment on the monitoring and diagnosis of hoist brake system were carried out. The research results showed: the monitoring and diagnosis methods are feasible.

• Journal of the Korean Society of Safety
• /
• v.27 no.3
• /
• pp.20-27
• /
• 2012

Mechanical seals are one of main components of high speed centrifugal pumps. So, it is very important to detect the faults (scratch, notch, indentation, wear) of mechanical seals since the damage of seal can cause a critical failures or accidents of machinery system. In the past, many researchers mainly performed to detect the seal fault using the time signals measured from sensors. Recently, studies are focused on the development of on-line real time monitoring system. But study on the feature parameters used for fault detection of mechanical seals has a little been performed. In this paper, we showed feature parameters extracted from accelerated and acoustic signals by using the discrete wavelet transform (DWT), alpha coefficient, statistical parameters. And also verified the possibility for fault detection of mechanical seal.