• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.7
• /
• pp.317-322
• /
• 2005

Advantages of switched reluctance motor(SRM) include a simple structure, the ability of operation in hash environments and under partial hardware failures, and a wide speed range. However design of SRM for industrial applications is very difficult because motor's inherent none-linearity and sensitivity of design parameter. In this paper, an optimal method for determining design parameters of a switched reluctance motor is researched. The dominant design parameters are stator and rotor pole arc and switching on and off angle. The parameters affecting performance are examined and selected using evolutionary computations and commercial CAD Program. The proposed design process is very fast. reliable and easy to access. The simulated design method proposed is compared with conventional procedure.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.12
• /
• pp.1-11
• /
• 1991

Multi rate circuit switching ISDN which assumes a star topology consisting of LANs(local area networks) interconnected through a backbone MAN (metropolitan area network) is considered. The stations are classified into two categories data and voice stations they are characterized by different arrival rate and session-length (holding time) statistics. We first model the data and voice terminals as finite-source stations and derive analytically exact expressions for the end-to-end blocking probabilities. For more exact evaluation, these probabilities are calculated in terms of three components:circuit blocking probability, destination busy probability and concurrent busy probability. For large size systems, we develop an develop an iterative algorithm that provides a computationally efficient and fast method for the calculation of the end-to-end blocking probabilities.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.3
• /
• pp.180-187
• /
• 2004

A conventional power supply of a microwave oven has a 60Hz transformer and high voltage capacitor(HVC). Though it is very simple and has low cost, it has several problems such as large size, heavy weight and low efficiency To improve these problems, various high frequency inverter type power supply have been investigated and developed in recent years. But these cost is higher than the conventional one due to additional control circuit, fast switching devces. In this paper, a novel pulse power supply for microwave oven using high frequency transformer embedded HVC(High Voltage Capacitor) is proposed for down-sizing, cost reduction and efficient improvement. To verify the effectiveness of the proposed transformer, an equivalent circuit of transformer embedded HVC is derived and it's characteristic is described. And the validity of the proposed pulse power supply embedded HVC-high frequency transformer is shown by simulations and experiments accroding to various operating conditions.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.534-536
• /
• 1996

In this paper we describe the method of optimum design for high-speed solenoid valve with fast switching time. The method of mathematical analysis adopted in this paper is that of using the permeance variation in the solenoid. And the effects of design particulars are investigated by simulation experiments. On the basis of experimental results we obtain the effective value of design parameter for high-speed solenoid valve.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.376-378
• /
• 1996

This paper presents a new PFC control method which replaces a fast line current measurement with a filtered load current measurement. Using the power balance relation between the input and the output of the boost converter. the input current can be described as the function of load current. Thus the PWM signal which effects the switching control of the boost converter is generated using the PFC input voltage, the PFC output voltage and the load current as input variables. By using a filter between the bridge rectifier and a dc-to-dc converter, the input voltage of the dc-to-dc converter is forced to always maintain above zero volt. Then the input current traces a sinewave in phase. The proposed scheme accomplishes a very high power factor and a low harmonic distortion of the line current. The validity of this scheme is demonstrated through simulation.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.365-368
• /
• 2001

The advantage of the squirrel cage induction motor is the brush less rotor. This advantage for operation and maintenance turns out to be a disadvantage for the detection of the cage rotor bar and endring defects, which means that the detection of cage faults is due to the measurement and analysis of only the stator input signals. The monitoring task in an inverter drive is complicated mainly because the voltage and current waveforms are nonsinusoidal and the high dv/dt values from fast switching inverterd distort the measurements. In this paper, we are going to discuss the detection method of broken rotor bar of the inverter fed squirrel cage induction motor by the motor current signature analysis(MCSA) and the opening terminal voltage signal analysis.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.256-259
• /
• 2003

In this paper describes the development testing results of high density High Voltage Power Supply(HVPS) that employ microwave TWTs. The HVPS consist of number of modules connected in series. A new design that adapt resonant circuit and high density pulse transformer to the high voltage modules makes the HVPS much more reliable. Also High voltage Solid-State modulation using fast switching devices(FET's) and the test results of modulator modules development are represented.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.4
• /
• pp.217-225
• /
• 1996

This paper describes a high power resonant inverter for diagnostic X-ray generators using zero-voltage soft-switching technology. The system consists of a step-down chopper, a resonant phase-shift PWM inverter, a hihg-voltage diode, and high voltage cables a smoothing DC capacitor. The inverter makes use the leakage inductance of the hihg-voltage transformer and external capacitor as resonant components. The rectified input voltage is controlled by a step-down chopper with input voltage compensator. The output regualtion is obtained by a resonant phase-shift PWM inverter with the digital feedback controller using DSP (digital signal processor), resulting in fast rising time and wide output voltage variation. The theoretical results are correlated with results from an experimental prototype of a 7-kVp, 300mA (21kW).

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.2
• /
• pp.104-111
• /
• 1997

In this paper, three-phase PWM AC to DC boost converter that operates with unity power factor and sinusodial input line currents is presented. The current control of this converter is based on the space vector PWM strategy with fixed switching frequency and the line currents track to reference currents within one sampling time interval. By using this control strategy low ripples in the outut current and the voltage as well as fast dynamic response are achieved with small dc link cpacitance employed.

• Journal of the Korean Ceramic Society
• /
• v.32 no.2
• /
• pp.147-154
• /
• 1995

Abnormal grain growth behavior of BaTiO3 ceramics with controlling of particle size distribution of calcined powder was investigated. The particle size distribution was controlled by changing the calcining temperature or by using of classification and regrinding process. With broadening of the normallized size distribution in calcined powder, it showeda normal grain growth behavior in sintered body due to an increase of volume fraction of seed grain in the calcined powder. It was supposed that the seed grains could easily contact each other for the rapid grain growth during sintering process and resulted in fast switching-over from abnormal to normal grain growth stage.