• 한국콘텐츠학회논문지
• /
• 제16권6호
• /
• pp.270-282
• /
• 2016

커뮤니티센터란 주거지구 인근에 위치하여 지역사회의 문화 활동의 중심이 되는 각종 공공시설을 의미한다. 최근 통합적 문화 활동의 수요가 증가하면서 커뮤니티센터가 단순 여가활동이 아닌 복지, 체육, 생활예술, 교육 등 공동체복원 및 생활편의를 증진시키는 복합적 공간으로 변모하고 있다. 본 연구는 세종시 주거지형 U-City 체험지구 개발사업의 일환으로, 지역민의 문화 참여 접근성을 제고한다. 특히 체험위주의 공간을 제공함으로서 사회적 통합을 유도하여 궁극적으로 U-City가 만드는 소통과 체감의 도시공간으로 회복하고자 한다. 본 연구를 통해 공동체 회복 기능의 커뮤니티센터를 집중 연구함으로서 주거지형 U-City 서비스 계획에 적용할 수 있는 실질적 대안을 마련할 수 있다. 이는 기존의 관람형, 강좌형의 일 방향 커뮤니티센터가 아닌 지역주민이 직접 체험하고 자발적으로 참여하는 쌍방향 운영의 커뮤니티센터의 발전방향을 제시했다는데 의의가 있다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.842-849
• /
• 2011

Open Rotor 엔진은 차세대 항공기를 위한 잠재적 기술향상을 제공할 수 있는 여러 신기술중의 하나이다. Open Rotor 엔진은 일반적 고바이패스 터보팬 엔진보다 향상된 추진 저하율을 가지며 고바이패스비와 공기역학적 진보한 형상의 팬 블레이드 설계의 결합으로 우수한 연료소모율을 구현한다. Open Rotor 엔진 성능 모델은 F404 터보제트 엔진를 코어로 사용한 GE36 엔진의 설계 및 시험데이터를 기반으로 해석하였다. 시험데이터를 이용하여 Open Rotor 엔진 성능 모델을 검증하였으며 최신 차세대 터보프롭 엔진 성능과의 비교를 통하여 적절하게 구성되었음을 확인하였다.

• Geomechanics and Engineering
• /
• 제15권2호
• /
• pp.775-781
• /
• 2018

Shake table tests were conducted on scaled tunnel model to investigate the mechanism and effect of seismic loadings on horseshoe scaled tunnel model in ground fissure site. Key technical details of the experimental test were set up, including similarity relations, boundary conditions, sensor layout, modelling methods were presented. Synthetic waves and El Centro waves were adopted as the input earthquake waves. Results measured from hanging wall and foot wall were compared and analyzed. It is found that the seismic loadings increased the subsidence of hanging wall and lead to the appearance and propagation of cracks. The values of acceleration, earth pressure and strain were greater in the hanging wall than those in the foot wall. The tunnel exhibited the greatest earth pressure on right and left arches, however, the earth pressure on the crown of arch is the second largest and the inverted arch has the least earth pressure in the same tunnel section. Therefore, the effect of the hanging wall on the seismic performance of metro tunnel in earth fissure ground should be considered in the seismic design.

• 한국산학기술학회논문지
• /
• 제9권4호
• /
• pp.1012-1017
• /
• 2008

최근 무선통신 기술의 발달과 편리성으로 무선 랜의 활용 증가하고 있다. 이와 더불어 무선랜의 보안 위협과 취약성에 대하여 이슈화 되고 있다. 따라서 IEEE에서는 802.11 표준안을 제정하고 무선 랜의 보안 취약점을 보완 하기 위해 802.11i등 새로운 표준들을 제정하고 있지만, 아직까지 해결되지 않은 보안 위협들이 존재한다. 본 논문에서는 액세스 포인트의 비콘 프레임을 이용하여 건물 내 액세스 포인트의 보안 상태 와 비인가 액세스 포인트를 탐지하는 시스템과 RSSI, 삼각측량범 및 칼만필터 알고리즘을 사용한 위치탐지 알고리즘을 제안하고, 기존 탐지 알고리즘과 제안 알고리즘의 결과 비교로 성능을 평가하였다.

• 산경연구논집
• /
• 제11권9호
• /
• pp.7-16
• /
• 2020

Purpose: Many studies show that promoting the development of trade facilitation has a positive role in stimulating the country's foreign trade. Therefore, it is of great practical significance to study the development level of trade facilitation for China's export trade. Research design, data and methodology:This study analyzes the growth trend of China's export trade volume in 2009-2019, the characteristics of China's export trade market according to the top 18 major exporting countries in 2017-2018, the structure of export commodities to understand China's economic development level, and compares the total amount of trade exported to all uses this to measure the level of trade development. On this basis, this paper selects the 2011-2018 Trade Facilitation Index and C continents to study the development trend. Based on the theory of trade facilitation, this paper constructs the Trade Facilitation Index, and hina's export trade volume for empirical research. Results: The results show that trade facilitation has a positive and significant impact on the development of China's export trade. Conclusions: Based on the analysis of the actual situations and empirical results, this paper puts forward some suggestions to promote the level of trade facilitation in order to promote the development of import and export trade.

• 설비공학논문집
• /
• 제10권6호
• /
• pp.753-762
• /
• 1998

A domestic refrigerator is composed of many components such as a compressor, evaporator, capillary tube, and the cabinet which plays a great role on the cycle performance, even if it is not the basic component part in the cycle. Recently, the restriction policy on the energy-saving and environmentally friendly refrigerator is reinforced in our nation as well as developed countries. Therefore, in this paper, cycle simulations and experiments were carried out ito understand the characteristics of the cycle performance using CFC 12, HFC 134a, and HC 600a and to know how changes in UA(overall heat transfer coefficients$\times$ heat transfer area) of evaporator, the position displacement of compressor, and the rpm of fan in the freezing room which has influence on the cycle performance. The result shows that the quantitative values of simulation and experiment are not coincident, but their trend is similar. When HFC 134a and HC 600a were used without the change of design in refrigerator used CFC 12, the performance of system in HC 600a is 30% lower, and the case of HFC 134a is 10% lower than that of CFC 12 on freezing temperature.

• 설비공학논문집
• /
• 제10권6호
• /
• pp.784-794
• /
• 1998

The present study has been directed at developing thermal models to investigate the dynamic behavior of a solar cooling system including an absorption chiller, solar collectors, a hot water storage tank, a fan coil unit, and the air-conditioned space. The operation of the system was simulated for 8 hours in two different operation modes. In the mode 1, the system operated without any capacity control.0 the mode 2, an auxiliary boiler supplied heat to the generator if hot water temperature became lower than a certain value. Moreover, the mass flow rate of hot water to the generator was controlled by comparing the instantaneous room air temperature with the design value. The variation of temperature and concentration in the system components and that of heat transfer rates in the system were obtained for both modes of operation. It was found that the room temperature was maintained near the desired value in the mode 2 by supplying auxiliary heat or controlling the mass flow rate of hot water, while the deviation of room temperature was quite great in the mode 2.

• Journal of the Korean Wood Science and Technology
• /
• 제44권2호
• /
• pp.204-217
• /
• 2016

Modified poplar has emerged as a potential raw material for furniture production. Lack of specific modified poplar strength information; however, restricts applications in the furniture industry especially as related to strength in corner-joints. Optimization of strength in L-shaped corner dowel modified poplar joints under compression loads utilizing finite element analysis (FEA) by Taguchi method with the focus of this study. Four experiment factors (i.e., Structure Style, Tenon Length, Tenon Diameter, and Tenon Gap), each at three levels, were conducted by adopting a $L_9-3^4$ Taguchi orthodoxy array (OA) to determine the optimal combination of factors and levels for the von Mises stress utilizing ANSYS software. Results of Signal-to-Noise ratio (S/N) analysis and the analysis of variance (ANOVA) revealed the optimal L-shaped corner dowel joint in modified poplar is $45^{\circ}$ Bevel Butt in structure style, 24 mm in tenon length, 6 mm in tenon diameter, and 20 mm in tenon gap. Tenon length and tenon gap are determined to be significant design factors for affecting von Mises Stress. Confirmation tests with optimal levels and experimental test indicated the predicted optimal condition is comparable to the actual experimental optimal condition.

• 한국광학회지
• /
• 제7권4호
• /
• pp.397-402
• /
• 1996

레이저 가스를 하나의 횡류팬만으로 순환시키는 동심 원통형 구조의 소형 엑시머레이저를 개발하였다. 이 방치를 1kHz의 고속으로 반복동작시켰을 때 KrF 레이저의 평균출력은 56watt였다. 본 논문에서는 kHz급의 소형 엑시머레이저를 실현할 수 있는 설계 파라메터와 레이저 가스의 CR(Clearing Ratio)특성을 분석하였다. 평균출력 56watt일 때 레이저 효율은 1.2%, CR은 2.97, 출력변동율 .+-.9%이다. 이때 레이저 가스용적은 10 liter이고 방전체적은 1.8(높이)*1.2(폭)*30(길이)=64.8$cm^{3}$이다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권4호
• /
• pp.462-470
• /
• 2015

In this study, we analyze the impacts of the trapezoidal fin shape of a double-gate FinFET on the electrical characteristics of circuits. The trapezoidal nature of a fin body is generated by varying the angle of the sidewall of the FinFET. A technology computer-aided-design (TCAD) simulation shows that the on-state current increases, and the capacitance becomes larger, as the bottom fin width increases. Several circuit performance metrics for both digital and analog circuits, such as the fan-out 4 (FO4) delay, ring oscillator (RO) frequency, and cut-off frequency, are evaluated with mixed-mode simulations using the 3D TCAD tool. The trapezoidal nature of the FinFET results in different effects on the driving current and gate capacitance. As a result, the propagation delay of an inverter decreases as the angle increases because of the higher on-current, and the FO4 speed and RO frequency increase as the angle increases but decrease for wider angles because of the higher impact on the capacitance rather than the driving strength. Finally, the simulation reveals that the trapezoidal angle range from $10^{\circ}$ to $20^{\circ}$ is a good tradeoff between larger on-current and higher capacitance for an optimum trapezoidal FinFET shape.