• Journal of Ocean Engineering and Technology
• /
• v.22 no.6
• /
• pp.1-6
• /
• 2008

Anchors have been commonly used to as foundation systems of the structures that require the uplift resistance. Recently anchors have been used in ocean sediment for mooring systems to stabilizeoffshore structures. In the saturated clayey soil however suction developed between the soil and andchor and affects the uplift capacity of anchor. To estimate the uplift capacity of the andchor accurately, the failure mechanisms of the andchor by the uplift force should also be correctly assumed. The uplift capacity is usually expressed in terms of breakout factors with respect to embedment ratio. In this paper, a two-dimensional plane strain numerical investigation into the vertical uplift capacity of a plate andchor in a clayey soil is described. The breakout factor against their corresponding values of embedment ratio was calculated and plotted along a single curve. The modes of failure mechanism at shallow and deep andchors are also presented.

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.176-184
• /
• 2005

When the weight if a concrete member makes problems. or when the cost of the concrete is relatively high, it may be economical to use a hollow concrete member. But a hollow R.C Pier may have poor ductility because of the brittle failure at the inner face of the hollow R.C Pier. This brittle failure results from the absence of the confinement at the inner face of the hollow R.C Pier. To avoid this brittle failure an internally confined hollow R.C Pier was developed. Test results show that the energy ductility ratio of a internally confined hollow R.C Pier have a superior energy ductility ratio to a general hollow R.C Pier.

• Journal of Industrial Technology
• /
• v.26 no.B
• /
• pp.93-99
• /
• 2006

Centrifuge model experiments were performed to investigate the confining effects of the sheet piles, installed to the sides of soft clay ground treated with sand compaction piles, on the bearing capacity and concentration ratio of composite ground. For the given g-level in the centrifuge model tests, replacement ratio of SCP and the width of surcharge loads on the surface of ground with SCP, the confining effects of installing the sheet piles on the edges of SCP ground on the bearing capacity, change of stress concentration ratio and failure mechanism were investigated. Kaolin, one of typical clay mineral, and Jumunjin standard sand were used as a soft clay ground and sand compaction pile irrespectively. As results of experiments, lateral confining effect by inserting the model sheet piles fixed to the loading plate was observed. For the strip surcharge loading condition, the yielding stress intensity in the form of the strip surcharge loads tends to increase with increasing the embedded depth of sheet piles. The stress concentration ratio was found not to be influenced consistently with the embedded depth of sheet piles whereas the effect of stress intensity on stress concentration ratio shows the general trend that values of stress concentration ratio are relatively high at the initial stage of loading and tend to decrease and converge to the certain values. For the failure mechanism in the case of reinforced with sheet piles, displacement behavior related to the punching failure, settlement right beneath the loading plate occurred since the soil was confined with sheet piles, was observed.

• Earthquakes and Structures
• /
• v.22 no.5
• /
• pp.461-473
• /
• 2022

Energy-saving block and invisible multiribbed frame composite wall (EBIMFCW) is an important shear wall, which is composed of energy-saving blocks, steel bars and concrete. This paper conducted seismic performance tests on six 1/2-scale EBIMFCW specimens, analyzed their failure process under horizontal reciprocating load, and studied the effect of axial compression ratio on the wall's hysteresis curve and skeleton curve, ductility, energy dissipation capacity, stiffness degradation, bearing capacity degradation. A formula for calculating the peak bearing capacity of such walls was proposed. Results showed that the EBIMFCW had experienced a long time deformation from cracking to failure and exhibited signs of failure. The three seismic fortification lines of the energy-saving block, internal multiribbed frame, and outer multiribbed frame sequentially played important roles. With the increase in axial compression ratio, the peak bearing capacity and ductility of the wall increased, whereas the initial stiffness decreased. The change in axial compression ratio had a small effect on the energy dissipation capacity of the wall. In the early stage of loading, the influence of axial compression ratio on wall stiffness and strength degradation was unremarkable. In the later stage of loading, the stiffness and strength degradation of walls with high axial compression ratio were low. The displacement ductility coefficients of the wall under vertical pressure were more than 3.0 indicating that this wall type has good deformation ability. The limit values of elastic displacement angle under weak earthquake and elastic-plastic displacement angle under strong earthquake of the EBIMFCW were1/800 and 1/80, respectively.

• Structural Engineering and Mechanics
• /
• v.34 no.2
• /
• pp.175-188
• /
• 2010

This paper deals with the buckling and postbuckling responses, and the progressive failure of square laminates of symmetric lay-up with a central rectangular cutout under in-plane shear load. A detailed investigation is made to show the effects of cutout size and cutout aspect ratio on the buckling and postbuckling responses, failure loads and failure characteristics of $(+45/-45/0/90)_{2s}$, $(+45/-45)_{4s}$ and $(0/90)_{4s}$ laminates. The 3-D Tsai-Hill criterion is used to predict the failure of a lamina while the onset of delamination is predicted by the interlaminar failure criterion. In addition, the effects of boundary conditions on buckling loads, failure loads, failure modes, and maximum transverse deflection for a $(+45/-45/0/90)_{2s}$ laminate with and without a square cutout have been presented. It is concluded that because of early onset of delamination at the net section of cutouts before first-ply failure, total strength of the laminate with very small cutouts can not be utilized.

• Journal of Korean Institute of Industrial Engineers
• /
• v.29 no.2
• /
• pp.145-149
• /
• 2003

We consider the estimation of failure rate and acceleration factor under type-I censoring without using acceleration model when testing is conducted in only one highly accelerated condition. Failure times of an item are assumed to be exponentially distributed. It is also assumed that the uncertainty about the acceleration factor, the failure time contraction ratio between accelerated condition and use condition, can be modeled by the uniform or gamma prior distribution of appropriate parameters. We respectively use Bayes and maximum likelihood approaches to estimate acceleration factor and failure rate in the use condition. An example is given to show how the method can be applied.

• Safety and Health at Work
• /
• v.4 no.4
• /
• pp.210-215
• /
• 2013

Background: This study aimed to identify the impacts of job stress and cognitive failure on patient safety incidents among hospital nurses in Korea. Methods: The study included 279 nurses who worked for at least 6 months in five general hospitals in Korea. Data were collected with self-administered questionnaires designed to measure job stress, cognitive failure, and patient safety incidents. Results: This study showed that 27.9% of the participants had experienced patient safety incidents in the past 6 months. Factors affecting incidents were found to be shift work [odds ratio (OR) = 6.85], cognitive failure (OR = 2.92), lacking job autonomy (OR = 0.97), and job instability (OR = 1.02). Conclusion: Patient safety incidents were affected by shift work, cognitive failure, and job stress. Many countermeasures to reduce the incidents caused by shift work, and plans to reduce job stress to reduce the workers' cognitive failure are required. In addition, there is a necessity to reduce job instability and clearly define the scope and authority for duties that are directly related to the patient's safety.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.635-642
• /
• 2004

Failure occurred slope, due to typhoon 'Rusa' and 'Maemi' last two years, was studied to evaluate the slope failure characteristics. There're three types of the slope in this study, ie. soil slope, rock slope, mixed slope. Statistical analysis was used to estimate the relation between slope type and failure mode. Among the failure occurred slope, soil slope & mixed slope are dominant at the ratio of 33%, 44% respectively. We conclude that soil slope & mixed slope have more higher risk than rock slope during heavy rainfall.

• Structural Engineering and Mechanics
• /
• v.32 no.2
• /
• pp.301-320
• /
• 2009

Damage assessment for buried structures against an internal blast is conducted by considering the soil-structure interaction. The structural element under analysis is assumed to be rigid-plastic and simply-supported at both ends. Shear failure, bending failure and combined failure modes are included based on five possible transverse velocity profiles. The maximum deflections with respect to shear and bending failure are derived respectively by employing proper failure criteria of the structural element. Pressure-Impulse diagrams to assess damage of the buried structures are subsequently developed. Comparisons have been done to evaluate the influences of the soil-structure interaction and the shear-to-bending strength ratio of the structural element. A case study for a buried reinforced concrete structure has been conducted to show the applicability of the proposed damage assessment method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.428-434
• /
• 2020

The one-shot weapon system is destroyed after only one mission. So, the system requires high reliability. Guided missiles are one-shot weapon systems that have to be analyzed by storage reliability since they spend most of their life in storage. The analysis results depend on the model and the ratio of correct censored data. This study was conducted to propose a method to more accurately predict the future failure rate of Air force guided missiles. In the proposed method, the failure rate is predicted by both MTTF (Mean Time To Failure) and MTBF (Mean Time Between Failure) models and the model with a smaller error from the real failure rate is selected. Next, with the selected model, the ratio of correct censored data is selected to minimize the error between the predicted failure rate and the real failure rate. Based on real field data, the comparative result is determined and the result shows that the proposed sampling rate can predict the future failure rate more accurately.