• Tribology and Lubricants
• /
• 제34권2호
• /
• pp.49-54
• /
• 2018

Hydraulic reciprocating seal has been widely used to prevent fluid leakage in hydraulic systems. Also, hydraulic reciprocating seal plays a significant role to provide lubricant film at contacting interface to minimize tribological problems due to sliding with counter material. To predict lifetime of hydraulic reciprocating seal, quantitative understanding of wear characteristics with respect to operating conditions such as normal force and sliding speed is needed. In this work, effect of sliding speed on wear of polyurethane (PU) hydraulic reciprocating seal were experimentally investigated using a pin-on-disk tribo-tester. The wear characteristics of PU specimens were quantitatively determined by comparing the confocal microscope data before and after test. It was found that the wear rate of PU specimens decreased from $4.9{\times}10^{-11}mm^3$ to $1.1{\times}10^{-11}mm^3/Nm$ as sliding speed increased from 120 mm/s to 940 mm/s. Also, it was observed that the friction decreased slightly as the sliding speed increased. Improvement of lubrication state with increasing sliding speed was likely to be responsible for this enhanced friction and wear characteristics. This result also suggests that decrease in sliding distance between PU elastomer and counter materials at lower sliding speed is preferred. Furthermore, the quantitative assessment of wear characteristics of PU specimen may be useful in prediction of lifetime of PU hydraulic reciprocating seal if the allowed degree of wear for failure of the seal is provided.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년도 춘계 학술대회 개요집
• /
• pp.30-32
• /
• 2006

The interfacial reaction and reliability of eutectic Sn-Pb and Pb-free eutectic Sn-Ag ball-grid-array (BGA) solders with an immersion Ag-plated Cu substrate were evaluated following isothermal aging at $150^{\circ}C$. During reflowing, the topmost Ag layer was dissolved completely into the molten solder, leaving the Cu layer exposed to the molten solder for both solder systems. A typical scallop-type Cu-Sn intermetallic compound (IMC) layer was formed at both of the solder/Cu interfaces during reflowing. The thickness of the Cu-Sn IMCs for both solders was found to increase linearly with the square root of isothermal aging time. The growth of the $Cu_3Sn$ layer for the Sn-37Pb solder was faster than that for the Sn-3.5Ag solder, In the case of the Sn-37Pb solder, the formation of the Pb-rich layer on the Cu-Sn IMC layer retarded the growth of the $Cu_6Sn_5$ IMC layer, and thereby increased the growth rate of the $Cu_3Sn$ IMC layer. In the ball shear test conducted on the Sn-37Pb/Ag-plated Cu joint after aging for 500h, fracturing occurred at the solder/$Cu_6Sn_5$ interface. The shear failure was significantly related to the interfacial adhesion strength between the Pb-rich and $Cu_6Sn_5$ IMC layers. On the other hand, all fracturing occurred in the bulk solder for the Sn-3.5Ag/Ag-plated Cu joint, which confirmed its desirable joint reliability.

• Nutrition Research and Practice
• /
• 제8권1호
• /
• pp.94-102
• /
• 2014

Diet attrition and failure of long term treatment are very frequent in obese patients. This study aimed to identify pre-treatment variables determining dropout and to customise the characteristics of those most likely to abandon the program before treatment, thus making it possible to modify the therapy to increase compliance. A total of 146 outpatients were consecutively enrolled; 73 patients followed a prescriptive diet while 73 followed a novel brief group Cognitive Behavioural Treatment (CBT) in addition to prescriptive diet. The two interventions lasted for six months. Anthropometric, demographic, psychological parameters and feeding behaviour were assessed, the last two with the Italian instrument VCAO Ansisa; than, a semi-structured interview was performed on motivation to lose weight. To identify the baseline dropout risk factors among these parameters, univariate and multivariate logistic models were used. Comparison of the results in the two different treatments showed a higher attrition rate in CBT group, despite no statistically significant difference between the two treatment arms (P = 0.127). Dropout patients did not differ significantly from those who did not dropout with regards to sex, age, Body Mass Index (BMI), history of cycling, education, work and marriage. Regardless of weight loss, the most important factor that determines the dropout appears to be a high level of stress revealed by General Health Questionnaire-28 items (GHQ-28) score within VCAO test. The identification of hindering factors during the assessment is fundamental to reduce the dropout risk. For subjects at risk, it would be useful to dedicate a stress management program before beginning a dietary restriction.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2003년도 가을 학술논문집
• /
• pp.202-206
• /
• 2003

본 연구에서는 방사성폐기물 아스팔트고화체를 장기간 저장시 형태유지가 되지 않는 단점을 보완하기 위하여 폴리에틸렌을 고화보조제로 아스팔트에 첨가하여 전처리의 분쇄 공정 없이 입상수지를 직접 고화처리 함으로서 시멘트 고화체처럼 형태안정성을 지니는 아스팔트 고화체를 제조하는 방법을 개발하고 이 방법에 의해 제조된 고화체의 침출특성을 평가하여 실제 방사성 폐이온 교환수지 처리에 적용함을 그 목적으로 하였다. 실험결과 고화보조제인 폴리에틸렌은 아스팔트와 폐수지가 혼합된 고화체내에서 가교역활을 하며 PE 함유량이 10 wt% 이상일 때 장기간 노출실험에서도 고화체 형태를 그대로 유지하였다. 최적조업조건은 폐수지의 함유량이 무게비로 40wt% 이고 PE의 함유량이 10wt%이며 이때 고화체내부에 수지입자의 밀도도 균일하게 분포됨을 확인하였다. 실험은 폐이온교환수지에 아스팔트를 혼합하고 여기에 폴리에틸렌(PE) 필름을 고화보조제로 첨가함으로서 고화체의 균일성, 수분과 접촉시 고화체의 침출을 최저로 하는 안정된 고화체를 개발하였다.

• 대한영양사협회학술지
• /
• 제13권3호
• /
• pp.277-294
• /
• 2007

The purposes of this study were to a) examine using status, b) measure the service quality attributes, c) analyze IPA and customer satisfaction, d) develop the LSM(Local Store Marketing) by location of K theme restaurant such as residential type(A), complex type(B) and downtown type(C). The questionnaires were handed out to 346 of 450(usage rate 76.9%). The statistical data analysis was completed using SPSS(ver 12.0) for descriptive analysis, $X^2$, t-test, ANOVA, reliability analysis, factor analysis, multiple linear regression. From an analysis on service quality attributes, most importance of service quality attributes was more highly perceived than performance of those, except for 'attractive exterior', 'variety of kid's menu', 'convenient facilities for kid' and perceived importance and performance were also significantly different by location of branch restaurant. The attributes to be improved were 'convenience of restaurant's parking lot', 'food tast', 'speedy service' and 'service competency' as branch A(residential type) restaurant, 'convenience of the restaurant location' as branch B(complex type) restaurant and 'convenience of the restaurant location' and 'speedy service' as branch C(downtown type) through IPA analysis. The Overall customer satisfaction was 3.74 and service quality factors had significant effect on overall customer satisfaction. Location of restaurant, which gives a great effect on its operation and marketing, has a important correlation with success or failure of restaurant business enterprises. Therefore, marketing strategy by restaurant location should be developed.

• 대한치과보철학회지
• /
• 제41권3호
• /
• pp.342-350
• /
• 2003

Statement of problem. Titanium-Nickel alloy might be used in various prosthetic restorations since it has a unique property such as super-elasticity and high fatigue resistance. However, little is known about the casting ability of this alloy. Purpose. This in vitro study compared the casting accuracy and the porosity made with different investments and various sprue designs to ascertain what casting condition would be better for the fabrication of Ti-Ni cast restorations. Material and methods. A total of 70 Ti-Ni alloy crowns were made and divided into 7 groups of 10 copings on a metal master die. For measuring the effect of the sprue numbers, two groups with one and two 8-gauge sprues were compared. Moreover, the results of the conventional sprue and the double thickness sprues were compared. Three investments were used; carbon free phosphate bonded investment, titanium investment and gypsum bonded investment. The cast restorations were evaluated at 48 points on the entire circumferential margin with a stereomicroscope measuring in micrometers. Each crown was radiographically examined for casting defects and porosity. Data on casting accuracy were analyzed using two-way and Post hoc Scheffe's comparison to determine whether significant differences existed at the 95% confidence level. Student-Newman-Keuls test were performed to identify significant differences in the number of voids. Results. The double sprueing group and double thickness group had significantly less marginal discrepancy than the single sprueing group (P<.05 and P<.01, respectively). The castings with phosphate bonded investment showed the least marginal discrepancy and the smoothest surface. The castings invested in the gypsum bonded investment had the greatest gaps in margin and the largest failure rate. The double sprueing group and phosphate bonded investment group had significantly smaller void numbers and smaller void size than the other groups. Conclusion. Within the limitations of this in vitro study, the casting accuracy of the groups using thicker, double sprue design and the phosphate bonded investment was significantly superior. Moreover, void number and size were less than other groups.

• KCI Concrete Journal
• /
• 제12권1호
• /
• pp.57-68
• /
• 2000

The effect of structure size on the nominal strength of unidirectional fiber-polymer composites, failing by propagation of a kink band with fiber microbuckling, is analyzed experimentally and theoretically. Tests of novel geometrically similar carbon-PEEK specimens, with notches slanted so as to lead to a pure kink band (without shear or splitting cracks), are conducted. The specimens are rectangular strips of widths 15.875, 31.75. and 63.5 mm (0.625, 1.25 and 2.5 in and gage lengths 39.7, 79.375 and 158.75 mm (1.563, 3.125 and 6.25 in.). They reveal the existence of a strong (deterministic. non-statistical) size effect. The doubly logarithmic plot of the nominal strength (load divided by size and thickness) versus the characteristic size agrees with the approximate size effect law proposed for quasibrittle failures in 1983 by Bazant This law represents a gradual transition from a horizontal asymptote, representing the case of no size effect (characteristic of plasticity or strength criteria), to an asymptote of slope -1/2 (characteristic of linear elastic fracture mechanics. LEFM) . The size effect law for notched specimens permits easy identification of the fracture energy of the kink bandand the length of the fracture process zone at the front of the band solely from the measurements of maximum loads. Optimum fits of the test results by the size effect law are obtained, and the size effect law parameters are then used to identify the material fracture characteristics, Particularly the fracture energy and the effective length of the fracture process zone. The results suggest that composite size effect must be considered in strengthening existing concrete structural members such as bridge columns and beams using a composite retrofitting technique.

• 전기학회논문지
• /
• 제66권12호
• /
• pp.1682-1688
• /
• 2017

In modern society, the number of industrial customers using equipment sensitive particularly to voltage sags is rapidly increasing. As voltage sags can cause loss of information as well as false operation of the control device, it results in the vast economic damage in industrial processes. One way to mitigate voltage sags in the sensitive loads is the installation of distributed generation (DGs) on the periphery of these loads. In addition, renewable energy sources are currently in the spot light as the potential solution for the energy crisis and environmental issues. In particular, wind power generation which is connected to a grid is rising rapidly because it is energy efficient and also economically feasible compared to other renewable energy sources. On the basis of the above information, in this paper, with Wind Turbine Generators (WTGs) installed nearby the sensitive load, the analysis of the mitigating effect comparison by types of WTGs is performed using voltage sag assessment on the IEEE-30 bus test system. That is, the areas of vulnerability according to types of WTGs are expected to be different by how much reactive power is produced or consumed as WTG reactive power capability is related to the types of WTGs. Using the concept of 'Vulnerable area' with the failure rate for buses and lines, the annual number of voltage sags at the sensitive load with the installation of WTGs per type is studied. This research will be anticipated to be useful data when determining the interconnection of wind power generation in the power system with the consideration of voltage sags.

• 한국전기전자재료학회논문지
• /
• 제29권9호
• /
• pp.559-564
• /
• 2016

This study examined the malfunction mode of the HCMOS IC under narrow-band high-power electromagnetic wave. Magnetron is used to a narrow-band electromagnetic source. MFR (malfunction failure rate) was measured to investigate the HCMOS IC. In addition, we measured the resistance between specific pins of ICs, which are exposed and not exposed to the electromagnetic wave, respectively. As a test result of measurement, malfunction mode is shown in three steps. Flicker mode causing a flicker in LED connected to output pin of IC is dominant in more than 7.96 kV/m electric field. Self-reset mode causing a voltage drop to the input and output of IC during electromagnetic wave radiation is dominant in more than 9.1 kV/m electric field. Power-reset mode making a IC remained malfunction after electromagnetic radiation is dominant in more than 20.89 kV/m. As a measurement result of pin-to-pin resistance of IC, the differences between IC exposed to electromagnetic wave and normal IC were minor. However, the five in two hundred IC show a relatively low resistance. This is considered to be the result of the breakdown of pn junction when latch-up in CMOS occurred. Based on the results, the susceptibility of HCMOS IC can be applied to a basic database to IC protection and impact analysis of narrow-band high-power electromagnetic waves.

• Toxicological Research
• /
• 제12권2호
• /
• pp.213-221
• /
• 1996

In order to develop a suitable secondary renal disease model and diagnostic markers of renal disease in the rat, the change of PIIIP (aminoterminal procollagen III peptide) in serum and hydroxyproline levels in the renal tissue that reflect the synthesis of extracellular matrix (ECM) during development of experimental renal diseases were observed. Two types of experimental primary diseases, diabetes mellitus administrated by streptozotocin (STZ, 75 mg/kg, i.p.) and liver cirrhosis produced by bile duct ligation/scission (BDL/s) operation, were induced. The hydroxyproline level increased according to the high PIIIP and NCl(carboxyterminal procollagen IV peptide) in Western blot analysis as early as 1 week in the STZ treated-rat kidney. Increased renal ECM was observed at 15 weeks in STZ and BDL/s model under the microscopic examination. High PAS positive reaction was found in capillary basement membrane in STZ treated-rats and mesangium in BDL/s operated rats at this time, showing the histological characteristics of diabetic nephropathy and cirrhotic glomerulonephritis in human, respectively. Such secondary renal failure were supported by additional tests including urinalysis and renal function test. The serum PIIIP detected by ELISA was a useful parameter to estimate synthesis rate of renal ECM during development of renal disease without extrarenal fibrosis i.e. liver cirrhosis in rats. This study is proposed that STZ treatment or BDL/s operation may be a suitable experimental animal model for the induction and development of chronic secondary renal diseases. Morover, it was found that hydroxyproline level in renal tissues was a good parameter of the change of renal ECM at the early stage of the diseases without apparent histological changes. Especially, serum PIIIP could be a choice as a diagnostic or prognostic marker during the development of renal diseases in rats.