• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.452-458
• /
• 2003

This paper presents a robust vibration control methodology of smart structural systems. The governing equations and associated boundary conditions are derived by Hamilton's principle. A robust controller is designed using a linear matrix inequality (LMI) approach to the multiobjective synthesis. The design objectives are to achieve a mix of H$\sub$$\infty$/ performance and H$_2$ performance satisfying constraints on the closed-loop pole locations in the face of model uncertainties. Numerical examples are presented to demonstrate the effectiveness of LMI approach in damping out the multiple modes of vibration of the piezo/beam system.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.2
• /
• pp.46-57
• /
• 2006

To estimate nondestructively strength performances of laminated woods, 3-ply parallel- and cross-laminated wood specimens exposed under atmosphere conditions after bending creep test were prepared for this study. The effects of density of species, arrangement of laminae and lamination types on dynamic MOE obtained by flexural vibration were investigated, and regression analyses were conducted in order to estimate static bending strength and bending creep performances. Dynamic MOE of parallel-laminated woods showed 1.0~1.2 times higher values than static bending MOE, and those of cross-laminated woods showed 1.0~1.4 times higher values than static bending MOE. The degree of anisotropy of dynamic MOE perpendicular to the grain of face laminae versus that parallel to the grain of face laminae was markedly decreased by cross-laminating. There were strong correlations between dynamic MOE by flexural vibration and static bending MOE (correlation coefficient r = 0.919~0.972) or bending MOR (correlation coefficient r = 0.811~0.947) of 3-ply laminated woods, and the correlation coefficient were higher in parallel-laminated woods than in cross-laminated woods. It indicated that static bending strength performances were able to be estimated from dynamic MOE by flexural vibration. Also, close correlations between the reciprocal of dynamic MOE by flexural vibration and initial compliance at 0.008 h of 3-ply laminated woods were found (correlation coefficient r = 0.873~0.991). However, the correlation coefficient between the reciprocal of dynamic MOE and creep compliance at 168 h of 3-ply laminated woods was considerably lower than those between dynamic MOE and initial compliance, and it was hard to estimate creep compliance with a high accuracy from dynamic MOE due to the variation of creep deformation.

• Korean journal of applied entomology
• /
• v.47 no.4
• /
• pp.487-490
• /
• 2008

Field collected larvae inside the pumpkin fruit in Jinan, Chonbuk Province were kept in the laboratory at $24{\pm}2^{\circ}C$, RH $65{\pm}5%$, and 14L:10D until they pupated and eclosed. Adults were fed with dry-milk based diet. Mating behavior was observed when they were 40 days old in a field cage at dusk in July and October, 2008. Wing vibration in male took place under the light intensity of 200 lux-20 lux, however, most commonly under 30 lux. Mounting between male and female was observed under 150 lux-30 lux after the act of wing vibration, also most frequently under 30 lux. Copulation occurred under 150 lux-20 lux. Females approached face to face to males which had been engaged in wing vibration and the copulation was successful for up to 64%. Copulation never occurred when a female positioned in front or at side of the male that was not engaged in wing vibration.

• Coupled systems mechanics
• /
• v.6 no.2
• /
• pp.207-227
• /
• 2017

In this paper Timoshenko beam theory is employed to investigate the vibration characteristics of functionally graded carbon nanotube-reinforced composite (FG-CNTRC) Beams with a stiff core in thermal environment. The material characteristic of carbon nanotubes (CNT) are supposed to change in the thickness direction in a functionally graded form. They can also be calculated through a micromechanical model where the CNT efficiency parameter is determined by matching the elastic modulus of CNTRCs calculated from the rule of mixture with those gained from the molecular dynamics simulations. The differential transform method (DTM) which is established upon the Taylor series expansion is one of the effective mathematical techniques employed to the differential governing equations of sandwich beams. Effects of carbon nanotube volume fraction, slenderness ratio, core-to-face sheet thickness ratio, different thermal environment and various boundary conditions on the free vibration characteristics of FG-CNTRC sandwich beams are studied. It is observed that vibration response of FG-CNTRC sandwich beams is prominently influenced by these parameters.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.3
• /
• pp.357-362
• /
• 2003

Recently, the demand for advanced technology of high precision and high efficiency processing of hard materials such as inconel is increasing with progress of industrial goods. However, the machinability of inconel is very inferior to the other conventional industrial materials and the machining technology for inconel involves many problems to be solved in machining accuracy, machining efficiency, etc. Therefore it is needs to establish the machining technology. The purpose of this study is to develop an advanced ultrasonic vibration machining technology for inconel, using the 60KHz and 75KHz high frequency, amplitude about 8${\mu}{\textrm}{m}$ and 4${\mu}{\textrm}{m}$, respectively. As the result, this new ultrasonic vibration machining is reasonable and suitable for the high efficient. accuracy machining method of inconel.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.10a
• /
• pp.451-455
• /
• 1997

This paper presents vibration mode control of a smart plate containing electro-rheological (ER) fluid between elastic face layers. Following the composition of a silicone oil-based ER fluid, the ER fluid-embedded plate partitioned into four sections is constructed. Then, an extensive modal test is experimentally carried out to identify field-dependent modal parameters such as mode shapes and natural frequencies of the structure with respect to different are subjected to electric fields. The distilled results from the experiment exhibit that the ER fluid can be effectively employed in a continuous fashion to tune modal behaviors of the distributed parameter systems,

• Structural Engineering and Mechanics
• /
• v.71 no.5
• /
• pp.459-467
• /
• 2019

In this paper, hyperbolic shear deformation theory is used for free vibration analysis of piezoelectric rectangular plate made of porous core. Various types of porosity distributions for the porous material is used. To obtain governing equations of motion, Hamilton's principle is used. The Navier's method is used to obtain numerical results of the problem in terms of significant parameters. One can conclude that free vibration responses are changed significantly with change of important parameters such as various porosities and dimensionless geometric parameters such as thickness to side length ratio and ratio of side lengths.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.3
• /
• pp.41-46
• /
• 2001

This paper discusses the feasibility of improving micro-machining accuracy by using two-dimensional(2-D) vibration cutting. Vibration cutting is generated by two piezo actuators arranged orthogonally : one is actuated by a sine curve voltage input, and the other is actuated by a phase-shifted sine curve voltage. A tool attached to the vibrator oscillates in a 2-D elliptical motion, depending on the frequencies, amplitudes, and the phase shifts of two input signals and the workpiece feedrate. Along the elliptical tool locus, cutting is done in the lower part, and non-cutting is done in the upper part. By this way a unique feature of 2-D vibration cutting, that is, air lubrication between a tool and chips, is caused. Another unique feature of 2-D vibration cutting was experimentally verified, that is, some negative thrust force occurs as the direction of chip movement on a tool rake face is reversed. Those features not only help chips flow smoothly and continuously but also reduce cutting force, which results in a higher quality machined surface. Through tool path simulations and experiments under several micro-machining conditions, the 2-D vibration cutting, compared to conventional cutting, was found to result in a great decrease in the cutting force, a much smoother surface, and much less burr.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.7 s.112
• /
• pp.697-703
• /
• 2006

This article proposes a new technique for the reduction of vibration and noise in the geared system by adjusting the distance between gear shafts. The vibration and noise may be produced by the abnormal force applied to the tooth face. And the force may be the cause of ununiform velocity in the driven shaft. If the velocity is obtained to be uniform by adjusting the distance between shafts. the vibration and noise may be reduced to some extent. In order to review, a dynamic analysis model for the gear train used in a mill turret and a test rig are developed. The velocities in the driven shaft are calculated by dynamic simulations for the model and noises in the test rig are measured with varying of the distance between shafts. The comparison of simulation and test data shows that the distance between shafts at the most uniform velocity has the lowest level of noise.

• Proceedings of the KIEE Conference
• /
• 2006.10d
• /
• pp.59-61
• /
• 2006

The single phase switched reluctance motor(SRM) is simpler in control circuit because the number of switching devices is fewer than the poly phase SRM. The energy density per unit volume is very big because all stator poles are excited simultaneously by a single switching power source. But it must be provided a starting device on account of not being generated the starting torque at specific rotor positions. And also it has some demerits that have a torque ripple, noise and vibration because of being excited by switching pulse power source. Therefore, to make up for these demerits, it is realized many studies for the structure design used by computer and the operating methods by power electronics technique. In this paper, we'll present the comparison of the single phase SRM with the various rotor pole face types, as like stepped rotor pole face type and general rotor pole face type. For the torque characteristics analysis.