• Laser Solutions
• /
• v.8 no.1
• /
• pp.39-44
• /
• 2005

We report experimental results on the periodic patterning using a Ti:sapphire femtosecond laser (800nm, 100fs, 1kHz). Periodic structures with reproducible basic patterns are produced both on the surface and inside transparent materials. Period patterning for the application to display panel is widely investigated. Also, the submicron dot and line patterns are fabricated inside fused silica glass, which is important for the formation of diffraction grating in integrated optical circuit. finally, we demonstrate the utility of the femtosecond laser application to optical memory by fabricating the three-dimensional dot patterns.

• Journal of Welding and Joining
• /
• v.17 no.6
• /
• pp.32-37
• /
• 1999

Since stainless steel plates have good mechanical properties, weldability, appearance and resistance of corrosion, these are traditionally used for vehicles such as the bus and the train. And they are mainly fabricated by spot welding. But fatigue strength of their spot welded joint is considerably influenced by welding conditions as well as geometrical factors. Thus a reasonable and systematic criterion for long life design of spot welded body structure must be established. In this report, strain energy density was analyzed by using 3-dimensional finite element model about the IB-type spot welded lap joint under tension-shear load. Fatigue tests were conducted on them having various thickness, joint angle, lapped length and width. From their results, it was found that fatigue strength of the IB-type spot welded lap joints could be effectively and systematically rearranged by strain energy density at the edge of nugget.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.464-464
• /
• 2011

We report a method to fabricate a large-area metal nanowire-grid polarizer. Liquid-bridge-mediated nanotransfer molding (LB-nTM) is based on the direct transfer of metal nanowires from a mold to a transparent substrate via liquid layer. A metal particle solution is used as an ink in the LB-nTM, which can be used for the formation of metal nanowires. The nanowires have higher depth are preferred for high transmittance. The height of nanowires that we made is about 140 nm. Large-area WGP is fabricated with good average transmittance of 74.89% in our measuring range.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.563-563
• /
• 2012

We report a one-step fabrication of single-crystal organic nanowire arrays on substrates using a new direct printing method (liquid-bridge-mediated nanotransfer moulding, LB-nTM), which can simultaneously enable the synthesis, alignment and patterning of the nanowires using molecular ink solutions. Two- or three-dimensional complex structures of various single-crystal organic nanowires were directly fabricated over a large area with a successive process. The position of the nanowires can be aligned easily on complex structures because the mold is movable on substrates before drying the polar liquid layer, which acts as an adhesive lubricant. This efficient manufacturing method can produce a wide range of optoelectronic devices and integrated circuits with single-crystal organic nanowires.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.560-560
• /
• 2012

We report a one-step fabrication method of Poly(9,9-dioctylfluorene) (PFO) nanowire array with pronounced ${\beta}$-Phase. We use liquid-bridge-mediated nanotransfer molding (LB-nTM) which is a new direct nano-patterning method based on the direct transfer of various materials from a mold to a substrate via liquid layer. The formation of the ${\beta}$-phase morphology in the resulting PFO nanowire array was evidenced by the presence of an absorption peak at 435nm. With the collection polarizer oriented parallel to the wire long axis, the PL emission was most intense and an emission dichroic ratio, DRE, of 3.7 was determined. The nanowire array have been investigated by scanning electron microscopy (SEM). Also, we simply fabricated structure of device of ITO/PFO nanowire arrays/Al and the electroluminescence spectra were recorded at various applied voltage.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.3
• /
• pp.241-244
• /
• 2014

Fabricating a crown to retrofit an existing abutment tooth for a partial removable dental prosthesis (PRDP) is one of the most time-consuming and labor-intensive clinical procedures. In particular, when the patient is concerned with esthetic aspects of restoration, the task of fabricating becomes more daunting. Many techniques for the fabrication of all-metallic or metal-ceramic crowns have been discussed in the literature. This article was aimed to describe a simple fabrication method in which a retrofitting crown was fabricated for a precise fit using a ceramic-pressed-to-metal system.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.8
• /
• pp.624-628
• /
• 2013

With the recent development of less-costly uncooled detector technology, expensive optics are among the remaining significant cost drivers in the thermography camera. As a potential solution to this problem, the fabrication of IR lenses using chalcogenide glass has been studied in recent years. We report on the molding and evaluation of a ultra-precision chalcogenide-glass lens for the thermography camera for body-temperature monitoring. In addition, we fabricated prototype thermography camera using the chalcogenide-glass lens and obtained the thermal image from the camera. In this work, it was found out that thermography camera discerned body-temperature between 20 and $50^{\circ}C$ through the analysis of thermal image. It is confirmed that thermography camera using the chalcogenide-glass lens is applicable to the body-temperature monitoring system.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.871-873
• /
• 2009

We report on the growth of rubrene ($C_{42}H_{28}$) wire fabricated by thermal evaporation, followed by solvent-vapor annealing for the application of organic thin film transistor. Solvent-vapor annealing was carried out in precisely controlled vapor pressure at elevated temperature. Micro-sized, and elongated rubrene wire was obtained via solvent annealing process reproducibly. Optical image and XRD data shows highly crystalline quality of rubrene wire.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.489-492
• /
• 2009

We report white OLED with high color temperature based on simple stacked structure for medical display applications. White OLED was fabricated with two emitting materials of fluorescent blue dopant and phosphorescent yellow dopant. We achieved luminance efficiency of 16.2cd/A and CIE color coordinates of (0.305, 0.317) at 10mA/$cm^2$. In particular, the correlated color temperature was higher than 7,000K, enough for display applications.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.21-23
• /
• 2003

MOCVD method is one of promising techniques which can fabricate YBCO coated conductors in a low Price A continuous reel-to-reel MOCVD device using a dispersed solid source was designed and manufactured. YBCO films were deposited on various substrates of metallic silver, (100) MgO and SrTiO3 single crystals. The chemical composition of the metal organic sources was changed to optimize the processing condition associate to the deposition of the stoichiometric Y3a2Cu3O7-y. We report the superconducting transition temperature, surface morphology and chemical composition of the YBCO film surfaces.