• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.4
• /
• pp.219-225
• /
• 2000

In this paper, we report the experimental setup and characterization of experimental results for the HTS antenna. The constructions of experimental setup must be fabricated, cautiously. We constructed the cryostat made of 3 stages which consists of radome, vacuum stage and helium refrigerator for the HTS antenna. The HTS antenna was mounted to cryostat and various characteristics were measured at room temperature and liquid nitrogen temperature, 77 K. Also the results for the HTS antenna and the gold antenna were compared in terms of reflection coefficient, E-plane and H-plane radiation pattern, input impedance, SWR and efficiency. It appeared that the HTS antenna was superior to gold counterpart over the all characteristics.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.824-827
• /
• 2004

High performance green $Ir(ppy)_3$-based phosphorescent OLEDs (PHOLEDs) have been fabricated by organic vapor phase deposition ($OVPD^{TM}$). In addition to demonstrating both efficiency and operational device lifetime comparable to devices built by vacuum thermal evaporation, we report on the controllability and stability of the $OVPD^{TM}$ process. Specifically, run-to-run and day-to-day deposition rate reproducibility of better than 2 % for three consecutive days is demonstrated.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.943-946
• /
• 2004

We report the laser scanning display as an emerging technology. We show demonstration system of laser TV, Video image is made by using a high speed MEMS scanning mirror and a direct-modulated red diode laser. We designed and fabricated MEMS scanning mirror. The first demonstration system showed a NTSC-resolution video image with the image size of 5 inches. The successful development of compact laser TV will open a new area of home application of the laser light.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1046-1048
• /
• 2004

Performances of organic thin film transistors (OTFTs) can be detrimentally affected by the state of the gate dielectric. Because of the bad stability of polymers, OTFTs with polymer gate dielectrics often provide abnormal characteristics. In this study, we report the condensation effect of the polymer gate dielectric layer. For the observations of the effect of the condensation, the spin-coated polymer layers with various deposition conditions were fabricated and left under low vacuum condition for several days. It is observed that the thickness of polymer layer and the electrical characteristic of OTFTs vary with the condensation time.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.91-94
• /
• 2004

We report on the opto-electronic properties of red, green, and blue poly (fluorene) co-polymer light-emitting devices (PLEDs) fabricated on a flexible plastic substrate. The plastic substrate used has a multi-layer structure with water vapor and oxygen transmission rates of less than $10^{-5}$ g/$cm^2$-day-atm and $10^{-7}$ cc/$cm^2$-day-atm, respectively. We obtained a wide range of color gamut and a maximum emission efficiency of 0.7, 10, and 1.7 cd/A for red, green, and blue PLEDs, respectively. Finally, a simple equivalent circuit model is proposed to simulate PLED current density-voltage characteristics.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.269-271
• /
• 2004

In this report, high-performance organic light-emitting diodes (OLEDs) with polytetrafluoroethylene (Teflon) buffer layer are demonstrated. Compared with conventional buffer layer, copper phthalocaynine (CuPc), Teflon film shows lower absorption in the wavelength from 200nm to 800nm The OLEDs with Teflon and CuPc buffer layer were fabricated under same conditions, and the device performances were compared. The results indicate that when the thickness of Teflon is 1.5nm, the performance of OLEDs is greatly enhanced with an efficiency of 9.0cd/A at the current density of 100mA/$cm^2$, while the device with an optimized 30-nm-thick CuPc buffer layer only shows an efficiency of6.4cd/A at the same current density.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.10
• /
• pp.1598-1602
• /
• 2004

In this paper, we report a microthermostat using PDMS (poly-dimethylsiloxane) and glass. This PDMS/glass chip is able to maintain constant temperature that is necessary for restriction enzyme reaction. Since PDMS is the low-cost and the mass-producible material and has very good biochemical compatibility, PDMS chip has more benefit than general Si chip. Heater was made of Au wiring patterned on Pyrex glass. A reaction chamber has a capacity of about 3 ${mu}ell$. We performed a restriction enzyme reaction by using the fabricated microthermostat and conventional method. Then, with the electrophoresis, we made a comparison between the result from the micro reactor and the one from conventional method.

• Journal of Electrochemical Science and Technology
• /
• v.10 no.4
• /
• pp.373-380
• /
• 2019

In this paper, we report the preparation of a flexible, self-standing and binder-free carbon nanotubes (CNTs) electrode with an electro-generated current collector. The copper current collector layer was electrodeposited on the backside of CNTs self-standing film obtained by a simple filtration process. The obtained CNTs-Cu assembly was used as a negative electrode in Li-ion batteries exhibiting good performance along with proving its applicability in flexible batteries.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.11a
• /
• pp.51-53
• /
• 2012

This paper is to report the results of mock-up test for concrete during severe cold weather. The temperature is fixed at -20℃. The mock-up specimens were fabricated simulating slab, wall and column. Heating coil with different heat capacity with 5 W and 15 W were embedded at slab specimen. Test results revealed that at -20℃, temperature dropped below 0℃ since around 70 hours. It takes 7 days to gain 45°D·D of maturity for avoiding frost damage at early age.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.11
• /
• pp.211-220
• /
• 2002

Optical disk drives read information by replacing a laser beam on the disk track. As information has become larger, the more accurate position control of a laser beam is necessary. In this paper, we report the analysis and fabrication of the micro mirror for optical disk drivers. A coupled simulation of gas flow and structural displacement of the micro mirror using the Finite-Element-Method is applied to this. The mirror was fabricated by using MEMS technology. Especially, the process using the lapping and polishing step after the bonding of the mirror and electrode plates was employed for the Process reliability. The mirror size was 2.5mm${\times}$3mm and it needed about 35V for displacement of 3.2 ${\mu}$.