• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.11
• /
• pp.1252-1259
• /
• 2003

The purpose of this study is to develop multi-functional fabrics by chitosan added on acrylic acid grafted cotton kintted fabrics. Therefore physical properties such as antimicrobial activity, deodorization rate, moisture regain, whiteness, and tensile strength of chitosan added on acrylic acid grafted cotton kintted fabrics were investigated. The results are as follows; According to increased chitosan's concentration, grafting yield was decreased. Therefore thickness of film by treated chitosan added on acrylic acid grafted cotton kintted fabric became thin. FT-IR spectra of chitosan add on acrylic acid grafted cotton kintted fabric clearly showed peaks of COOH and NH$_2$. Antimicrobial activity and deodorization rate of chitosan add on acrylic acid grafted cotton kintted fabrics were increased greatly than untreated. And their durability of laundry were good, Moisture regain of treated fabrics was higher than untreated. Whiteness and tensile strength of treated fabrics were lower than untreated.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.6
• /
• pp.17-24
• /
• 2002

The objective of the present research is to evaluate the wave propagation velocity and attenuation characteristics of kaolin clay specimens using ultrasonic testing. Test specimens with known initial micro-fabric were prepared using a two-stage slurry consolidation technique. For a known state of stress conditions, initial void ratio, and micro-fabric, a series of experiments were conducted to evaluate the longitudinal wave propagation velocity and associated damping behavior. The effects of major variables involved in ultrasonic testing of cohesive soil were considered in this study. Ultrasonic velocity was not correlated to the microfabric structure under the given consolidated pressure whereas ultrasonic attenuation was affected by the microstructural properties of the specimen.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.3
• /
• pp.15-21
• /
• 2009

The anisotropic mechanical properties were measured for the three orthogonal orientations of plain weave glass fabric reinforced epoxy resin laminate. In tensile and flexural tests, axial and edge type specimens failed by pull-out of warp and fill yarns, respectively. In contrast, the thickness type specimens failed by adhesive failure process. Longitudinal cracking occurred in several of the edge type specimens during tensile test. That cracking caused pop-in in the stress-strain curve. Defects induced by improper coupon machining caused that cracking.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 1999.03a
• /
• pp.153-157
• /
• 1999

Voigt Model assumed for creep was used to obtain the viscoelastic properties of fabrics in thickness direction and the governing equation was derived. The weights were specially designed and calibrated for constant stress applied to fabrics and the 1 ${\mu}{\textrm}{m}$ resolution laser displacement sensor was attached in order to measure the variation of strain. Ten fabric samples were used. The few steps of strain showed according to the internal structure of fabrics. Also correlations the Hand Values from KESF with the spring and damping coefficients were considered.

• Korean Journal of Human Ecology
• /
• v.7 no.2
• /
• pp.75-80
• /
• 1998

In this paper, deying properties and colorfastness of ramie, flax, and cotton fabrics for direct dyes were compared. When dyed in a same dyeing bath ratio, in case of green dyes, colorfastness to light was similar for three fabrics but in case of red dyes, cotton had a lower level. For colorfastness to laundering, three fabrics were similar and there were no consistent differences. The degree of stain about white fabric cotton was highest in case of red dyes. The degree of stain about white fabric wool showed the high resistance of stain and little stain was seen. This result represented that the used dyes were proper direct dyes for cellulosic fibers. For the difference of shade, the cotton was cosistently brighter and the shade of ramie was darker than of cotton and flax. This might mean that optical effects arouse from the comparatively large cross-sectional size of the ramie fiber and its highly ordered structure.

• Elastomers and Composites
• /
• v.1 no.1
• /
• pp.41-48
• /
• 1966

The physical properties of rubber coated fabrics, treated by means of spreading and topping process were studied. 1. The tearing strength of the rubber coated fabrics has shown decreasing tendency in comparison with fabric itself 2. Generally, the tearing strength is inversely proportional to the adhesion. 3. The value of hydrostatic pressure is in proportion to the density and tensile strength of the fabrics. 4. The topping process shows greater difference in adhesion initial and after water immersion than spreading process.

• Textile Coloration and Finishing
• /
• v.14 no.5
• /
• pp.261-267
• /
• 2002

Cotton fabrics were immersed in aqueous solution of N-methylmorpholine N-oxide(NMMO) with various concentrations, padded by 300% of pick-up, concentrated at $90^\circ{C}$ for 30min under constant-length condition, washed, and dried, to examine a possibility of linen-like finishing by the solvent bonding between fibers. With increasing the concentration of NMMO, cross-sections of fibers changed to oval or polygonal shapes and not only the fibers but also the warp and weft were bonded each other, which produced linen-like effect on the fabrics in the aspects of appearance and mechanical properties such as the Increase of stiffness and shear properties. The thickness, moisture regain and dyeability were increased with the concentration of NMMO.

• Textile Coloration and Finishing
• /
• v.12 no.5
• /
• pp.280-287
• /
• 2000

For thousands of years, dyes were obtained from natural sources, such as plants and animals. Although synthetic dyes have replaced many natural dyes for commercial use but natural dyes with their fascinating color are still used extensively by some people. To investigate the dyeing properties of chestnut bur, which is most widely found in our country, some experiments were performed under the several dyeing conditions with silk and cotton fabrics. It was found that $\lambda_{max}$ of chestnut but extract was 410nm and the color of the fabric dyed is Yellow Red. The K/S value of silk and cotton fabrics increased when the dyeing temperature was higher than $60^\circ{C}$ and the dyeing time was more than 30 minutes. Optimal dyeing pH was between 5 and 6, and repetition of dyeing increased K/S value of the sample fabrics. K/S value of silk fabric dyed with chestnut bur extract was higher than that of cotton. Post-mordanting method showed higher color yield compared with pre-mordanting, and higher temperature and increased time in mordanting increased the dye-uptake.

• Textile Coloration and Finishing
• /
• v.33 no.3
• /
• pp.97-104
• /
• 2021

In this study, the dyeability of m-aramid fabric with various cationic dyes using two bath two step dyeing method were investigated. The exhaustion properties of Doracryl series recommend for aramid(Doracryl^® Red GL 100%(DR), Doracryl^® Blue GL 300%(DB), Doracryl^® Yellow XGRL 200%(DY)) and commercial cationic Synocryl series(Synocryl^® Red GRL ED(SR), Synocryl^® Blue GSL ED(SB), Synocryl^® Yellow 3RL ED(SY)) for acrylic were measured by using Dye-O-meter. In the presence of carrier, the exhaustions of Doracryl series were higher to those of Synocryl series and the opposite phenomenon was observed in the absence of carrier. And the severe migrations of cationic dyes to acetate, nylon and wool fabrics were observed without carrier.

• Journal of Digital Contents Society
• /
• v.7 no.4
• /
• pp.287-294
• /
• 2006

Mass-customization is fast growing a segment of the apparel market. 2D Virtual wearing system is one of visual support tools that make possible to sell apparel before producing and reduce the time and costs related to product development and manufacturing in the world of apparel mass-customization. This paper is related to fabric color mapping method for 2D image-based virtual wearing system. In proposed method, clothing shape section of interest is segmented from a clothes model image using a region growing method, and then mapping a new fabric color selected by user into it based on its intensity difference map is processed. With the proposed method in 2D virtual wearing system, regardless of color or intensity of model clothes, it is possible to virtually change the fabric color with holding the illumination and shading properties of the selected clothing shape section, and also to quickly and easily simulate, compare, and select multiple fabric color combinations for individual styles or entire outfits.