• Journal of Energy Engineering
• /
• v.7 no.1
• /
• pp.103-112
• /
• 1998

A high temperature fabric filter was developed and characterized in order to solve the various problems encountered in the operation of industrial fabric filters. Four kinds of dusts generated in the typical domestic industry were used for its characterization, coke dust from a steel manufacturing process, cement dust from a cement manufacturing process, fly ash from a fluidized-bed combustor, and incinerator ash from a waste plastics incinerator. The physical and chemical properties of the high temperature fabric filter were analyzed in terms of mean flow pore pressure, bubble point pore diameter, mean flow pore diameter, pore size distribution, and the changes in tensile strength and initial elastic modulus under $SO_2$ and $NO_2$ atmospheres. Pressure drop, dust penetration, and figure of merit for the fabric filter were also investigated in a bench-scale filter testing unit. The fabric filter developed in this study had good physical and chemical filter properties and showed a very applicability to typical industrial dusts treatments.

• Composites Research
• /
• v.28 no.5
• /
• pp.285-290
• /
• 2015

Multiscale multiphysics in structural batteries make mechanical property testing difficult. In this research, the effect of electrolyte-coating on the mechanical performance of carbon fabric was studied using a suitable mechanical test method for structural batteries. For this experiment, two types of specimens were determined their dimension according to ASTM. One type of specimen was smaller than the standard dimension. The specimens were coated by spreading the electrolyte material on carbon fabric, hardened using epoxy, and tested for tensile properties using universal testing machine. As a result, it was found that the mechanical properties of carbon fabric were not influenced by electrolyte coating. In addition, the small-scale specimen used in this experiment was determined to be sufficiently reliable.

• Textile Coloration and Finishing
• /
• v.13 no.2
• /
• pp.120-127
• /
• 2001

In order to make a microfiber fabric with PET/Co-PET Sea-Island Type microfiber, the optimum condition of extraction and elimination of Co-PET from the mocrofiber was examined. At the same time, the physical property change of the fabric with respect to the change of the relative amount of the Co-PET in the microfiber was also examined to provide a directly applicable data set to the industry. The sample fabric used was warp 75/36(DTY) and weft 0.05d(PET/Co-PET, Sea Island Type Microfiber) twill fabric of 36 separated yarns＋40/24(high shrinking yarn) with 130/48 ITY. The data set was made at various NaOH concentrations and steam temperatures with time as a main variable. The physical properties examined were the tensile properties. The results obtained were the tensile. The results obtained were 1. For a proper extraction of Co-PET (13.5%)from the microfiber with wet curing, it takes more than 5 min. in 8 and 12% of NaOH solutions but it takes only 3 min. in 18% of NaOH solution at 12$0^{\circ}C$. 2. For a proper extraction of Co-PET (13.5%) from the microfiber with wet curing, ti takes 3~5min. in 12 and 14% of NaOH solution and it takes less than 3 min. in 18% of NaOH solution at $130^\circ{C}$. 3. The increasing ratio of WT increased with increasing NaOH concentrations and the equilibrium point reached was 3 min. at $120^\circ{C}$. 4. The WT increasing ratio was greater in 14 and 18% NaOH solutions than in 8 and 12% of NaOH solutions at $130^\circ{C}$5. The RT ratio changes at $120^\circ{C}$ in 8 and 12% of NaOH solutions were indifferent from that at $130^\circ{C}$ in 12% of NaOH solution. However, the RT was apparently decreased with increasing NaOH concentration.

• Journal of Fashion Business
• /
• v.16 no.2
• /
• pp.151-162
• /
• 2012

The industry-wide development of digital technologies has also affected the textile and fashion industries immensely. The applications of 3D technology, virtual reality, and/or augmented reality systems have helped to create novel fashion brands based on the marriage of IT and textile/fashion industries. 3D digital virtual clothing systems have been developed to help the textile and fashion industries in terms of the planning, manufacturing, marketing and sales sectors. So far, most of the development effort for the 3d virtual clothing systems has been focused on the woven fabrics. The characteristics of woven fabrics differ from those of knitted fabric. Since the physical structures and mechanical properties of the knitted fabrics are definitely different from those of woven fabrics, the simulation process for the knitted fabrics should follow different approaches. The loops in a knitted fabric deform easily. The deformation results in a readily stretchable fabric appearance. Cloth simulation mostly employs models that approximate the mechanical properties of linear elastic planes. This simulation scheme does not, however, describe well enough the behavior of knitted fabrics, which deviate largely from the linear isotropic material characteristics. This study aims at characterizing the tensile deformation and surface textures of a knitted fabric product. Tensile deformation curves for the wale, course, and bias direction are analyzed. The surface texture of the knitted fabric is analyzed by using a 3-dimensional scanning device.

• Textile Coloration and Finishing
• /
• v.32 no.3
• /
• pp.176-183
• /
• 2020

In order to study wearable air cushion materials capable of responding to massive impact in high-altitude fall situation, high tenacity woven fabrics were bonded by heat only depending on various type of thermoplastic films and then mechanical properties were measured. Tensile strength, elongation, and 100% modulus measurement results for 4 types of films show that TPU-2 has higher impact resistance and easier expansion than PET-1. After thermal bonding, the combination with the highest tensile strength was a material with a TPU-2 film for nylon and a PET-2 film for PET, so there was a difference by type of fabric. The tear strength of the bonded materials were increased compared to the fabric alone, which shows that durability against damage such as tearing can be obtained through film adhesion. All of the peel strengths exceeded the values required by automobile airbags by about 5 times, and the TPU-2 bonded fabric showed the highest value. The air permeability was 0 L/dm2 /min. For both the film and the bonded material, which means tightness between the fabric and the film through thermal bonding. It is expected to be applied as a wearable air cushion material by achieving a level of mechanical properties similar to or superior to that of automobile airbags through the method of bonding film and fabric by thermal bonding.

• The Journal of Engineering Geology
• /
• v.11 no.2
• /
• pp.191-203
• /
• 2001

We investigate mechanical anisotropy dependent of rock fabric and its relationship with microcracks in the Pocheon Granite. Uniaxial compressive strengths range from 177MPa to 212MPa and the elastic constants are 48GPa-62GPa. The tensile strengths are 6.9MPa~8.5MPa and ultrasonic wave velocities range between 3,200m/sec and 3,700m/sec, indicating that mechanical anisotropy is strongly dependent of rock fabric. The minimum anisotropy ratio is 14% and the maximum is 24%, depend on the mechanical properties. The preferred orientations of microcracks are closely related with the directions of rock fabric. The preferred orientations of microcracks in feldspar are governed by the direction of mineralogical axis and are different from the directions of rock fabric. However, microcracks in quartz grains are very long and parallel to the directions of rock fabric, indicating that directions of rock fabric may be governed by the preferred orientations of microcracks in quartz grains. The preferred orientations of microcracks measured by differential strain analysis and microscopic observation are slightly different. That may be caused by different methodology. Lengths and numbers of microcrack are measured by microscopic observation. However, differential strain analysis measures the widths of microcracks.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2011.11a
• /
• pp.43-44
• /
• 2011

• The International Journal of Costume Culture
• /
• v.7 no.2
• /
• pp.77-86
• /
• 2004

The purpose of this study is to characterize physical and tensile properties according to a knitting method as basic materials for solving the difficulties that occur due to the fact that the crosswise elongation is most different among knit stitch at the time of measuring elongation of knitwear. The sample used for this study was wool $100\%$ and was knitted into two, that is, controlled loop length controlled to properties of structure and fixed loop length by using Shimaseiki SES-124S 12G computer automatic flat knitting machine with DSCS device. Also, the density of rib fabric was 12gauge and its quantity was a total of seven of $0{\times}0,\;1{\times}1,\;2{\times}1,\;2{\times}2,\;3{\times}3,\;4{\times}4$ and including plain fabric, and knitted 2 pieces of sample of 300 wale${\times}400$ course. In conclusion, rib stitch has the much higher stretch rate in the direction of the course than other stitches.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2008.04a
• /
• pp.37-39
• /
• 2008

The purpose of this study is to improve the defects of DPP fabric by heat setting and to describe the change of physical properties of DPP fabrics. The thermosetting was carried out in autoclave from 100 to 140$^{\circ}C$ temperature range for 10min.. In this study, we investigated the effect of the thermosetting temperatures on the structural, thermal, mechanical properties and dyeability of DPP fabrics. The melting peak of multi peak changed to single peak with an increased thermosetting temperatures. The melting energy(J/g), the tensile strength and elongation were found to increase with increasing temperature of heat setting. The diffraction peak at Bragg angle(2${\theta}$) about 13.8$^{\circ}$ were very strong, and diffraction intensity, d-spacing and half-width decreased with increasing thermosetting temperatures. On the other hand, the dyeability(K/S) and crease recovery decreased with an increasing thermosetting temperatures.

• Textile Coloration and Finishing
• /
• v.15 no.6
• /
• pp.33-38
• /
• 2003

This study surveys the effects of POY physical properties and processing conditions of belt texturing machine to the textured yarns. The various textured yarns are made with the variations of 1st heater temperature, draw ratio, velocity ratio, and the physical properties of these specimens such as yam linear density, tenacity, breaking strain, and wet and dry thermal shrinkages are measured and analysed with the various processing conditions of texturing machine. Especially, the thermal characteristics of the textured yarns, which are affected at the fabric hands and the determination of the processing conditions in the dyeing and finishing processes, are investigated through the thermal stress analyser and DSC experiments.