• Journal of the Korean Society of Clothing and Textiles
• /
• v.21 no.6
• /
• pp.1041-1050
• /
• 1997

This study was carried out to improve the thermal insulation properties of wool and wool- like fabrics by treating the fabrics with polyethylene glycol, to evaluate the fabric hand of PEG treated wool and wool-like fabrics and to grade up the fabric hand of the treated fabrics by treating with softening agents. Wool and wool-like fabrics were treated with high molecular PEG-8,000 by PDC. The thermal release/storage properties were measured on a DSC. Hand of specimens were evaluated by KES-FB system. The results were as follows; 1. PEG-treated fabrics showed thermal storage and thermal release properties by DSC and the heat contents were generally proportional to the add-ons. 2. PEG-treated fabrics showed higher Koshi and lower Numeri and Sofutosa values due to lower tensile energy and recovery and higher bending rigidity and shear stiffness as the add- ons increased. 3. PEG-treated fabrics showed much lower bending rigidity after softening agents treatment.

• Fibers and Polymers
• /
• v.4 no.4
• /
• pp.151-155
• /
• 2003

The abrasion behavior of three kinds of warp knitted fabrics, which are normally used for upper sole of footwear, was evaluated. We measured the changes of mechanical and structural properties of each sample as abrasion cycle increased. Each sample showed similar trends in compression and surface properties but there were significant differences in abrasion rate among the samples. The mechanical properties showed remarkable differences with directions. The frictional coefficient (MIU) of fabric surface increased at the beginning of abrasion and decreased as abrasion cycles increased. The weight and thickness of the fabric linearly decreased with abrasion cycles. The surface roughness (SMD) and the compressional resilience (RC) decreased as abrasion cycles increased while compressional energy (WC) increased.

• Textile Coloration and Finishing
• /
• v.12 no.6
• /
• pp.337-343
• /
• 2000

In this study, the five harness satins are weaved in rapier loom and air-jet loom each using the pure wool Nm 2/72, also the physical characteristics of fabrics that are produced in these weaving machinery in same condition are measured by using the KES-FB system. The results of analysis and comparison on each fabric are presented by classifying items, that is to say, the tensile, bending properties. The results we as follows ; The extensibility of grey fabric woven by rapier in the weft direction is larger than that by air-jet loom. The variation of bending property of grey fabric woven by rapier in the weft direction is more irregular than that by air-jet loom. However, these properties are similar both rapier and air jet fabrics.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.178-179
• /
• 2021

Comparing the absorption volume of test pieces immersed over time in room temperature moisture with weight, WF absorbed about 40% more than PLAIN, and PLAIN stopped absorbing after 10 minutes, but WF continued to absorb. It is thought that the woven fabric layer of the core material continued to absorb moisture. In the heat transfer test, the test piece to which only WF was applied had a temperature difference of about 2℃ compared to PLAIN, and when the insulating liquid was sprayed, there was a difference in heat transfer properties of up to 5℃. This is judged to have low heat transfer properties of the basic woven fabric, but the heat insulating liquid also further reduces heat transfer properties.

• Fashion & Textile Research Journal
• /
• v.20 no.1
• /
• pp.93-100
• /
• 2018

This study comparatively analyzed the changes in the dimensional stability and the mechanical properties of stretch knit fabrics associated with washings conditions in order to determine the most appropriate washing method. Polyester and spandex knit fabrics were washed 25 cycles with nine washing condition profiles that controled detergent, hardness. temperature and RPM. The knit fabrics with repeated washings were evaluated by dimensional stability and measured by the KES-FB system. Polyester and spandex fibers have good chemical resistance. However, the changes in the dimensional stability and the mechanical properties were observed in washed knit fabrics. After repeated washings, the knit fabrics washed in an alkali or neutral detergent had good dimensional stability compared with the knit fabric washed in functional detergent. The washed knit fabrics were extended, stiff, rough, and had a smaller volume. The changes were the result of the rearrange of polyester fibers which twisted around spandex core and chemical interactions involving the detergent and the physical and mechanical forces of washing. Especially, using an alkali detergent resulted in increased stiffness and roughness of the knit fabric. In conclusion, the washing in water with low hardness and a neutral detergent can minimize the changes in dimensional stability and mechanical properties of polyester and spandex knit fabric.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.41 no.1
• /
• pp.60-70
• /
• 2017

This study selects representative materials and sewing methods used to: produce medical compression clothing in domestic garment, understand physical properties according to sewing conditions before and after knitting, and propose a sewing method that can improve the functional properties of the medical pressure clothing for burn patients. This experiment used samples from two knitted fabrics of high-frequency, produced and sold among fabrics used to produce medical compression clothing in Korea. Sewing methods were N321, N502 and N601, most commonly used in the press clothing industry. Fabric A is most often reduced in EMT values when sewing N502. However, N321 and N502 are suitable sewing methods for the reliable to twist at the larger torsional shear and the larger 2HG, 2HG5 value. Fabric B is sewn with N601, the EMT value is the most elevated, LT value is also low and extensibility improves after sewing. N601 is shown as an appropriate sewing method for warp knitting. When sewing with N321, the torsional is stable but elongation is lacking. N502 is not good for torsional stability.

• Textile Coloration and Finishing
• /
• v.31 no.4
• /
• pp.288-297
• /
• 2019

The specimens were heat treated at 180℃, 190℃, 200℃, 210℃ and 220℃ to observe the change of the physical properties of the double raschel pile fabric. The density, tensile strength, weight, elongation, dyeing characteristics, fabric surface morphology and cross sectional shape were observed by heat treatment temperature. Compared with untreated samples, weight, density and tensile strength were increased with increasing heat treatment temperature. No increase was observed at 220℃. In the case of elongation, it increased to 190℃ but thereafter it could not be observed. In the case of uprightness of brushed hair, it was observed that the gap between the yarns was narrowed and the density was increased and the straightness of the yarn and pile yarn was improved by widening the heat treatment temperature. As a result, it was observed that the uprightness was remarkably improved and the bulky properties was increased. It was also observed that the increase of the dyeability was observed with increasing the heat treatment temperature.

• Polymer(Korea)
• /
• v.24 no.2
• /
• pp.276-280
• /
• 2000

A conductive poly(acrylonitrile)/polypyrrole composite fabric was prepared. A conductive composite was prepared by the impregnation of PAN fabric into a mixed solution of pyrrole and oxidant in order to induce the in-situ polymerization of a conducting polymer into the matrix fabric. In the composite formation, the reaction condition was optimized to achieve the best properties, and the effect of the externally-added arylsulfonate dopants on the physical properties was examined. As a result, the best properties of electrical conductivity, thermal stability, and fastness to washing, was observed in the composite containing an antraquinonesulfonate (AQSA) dopant.

• Fibers and Polymers
• /
• v.2 no.4
• /
• pp.196-202
• /
• 2001

In order to investigate the relationship between subjective sensation for fabric sound and touch and the objective measurements, eight different apparel fabrics were selected as specimens. Sound parameters of fabrics including level pressure of total sound (LPT), level range (ΔL), and frequency differences (Δf) and mechanical properties by Kawabata Evaluation System (KES) were obtained. For subjective evaluation, seven aspects of the sound (softness, loudness, pleasantness, sharpness, clearness, roughness, and highness) and eight of the tough (hardness, smoothness, fineness, coolness, pliability, crispness, heaviness, and thickness) were rated using semantic differential scale. Polyester ultrasuede was evaluated to sound softer and more pleasant while polyester taffeta to sound louder and rougher than any other fabrics. Wool fabric such as worsted and woolen showed similar sensation for sound but differed in some touch sensation in that woolen was coarseast, heaviest, and thickest in touch. In the prediction model for sound sensation, LPT affected positively subjective roughness and highness as well as loudness, while ΔL was found as a parameter related positively with softness and pleasantness. Touch sensation was explained by some of mechanical properties such as surface, compressional, shear, and bending properties implying that a touch sensation could be expressed by a variety of properties.

• Korean Journal of Human Ecology
• /
• v.24 no.2
• /
• pp.285-295
• /
• 2015

To identify optimized thermal properties of mold brassiere cup for improved thermal comfort during summer, we compared the thermal resistance and the water vapor permeability of Polyurethane (PU) foam, 3D spacer fabric and the two combined materials of the PU foam and the 3D spacer fabric. Four experimental mold brassieres were made of the materials for wearing test. Six women in their twenties evaluated the wearing sensation in the hot and humid environment. The changes in microclimate temperature and humidity while wearing test brassiere cups were measured. Results indicate that thermal resistance increased as more PU foam were combined, while the water vapor permeability was higher as the content of the 3D spacer fabric increased at thickness of 18mm and over. However, in the wear test, the PU foam brassiere was the most preferred in all ambient conditions due to its soft, flexible and smooth texture, despite its high thermal resistance and low water vapor permeability. This indicates that the textures of mold foams are more dominant properties than thermal properties for mold foams in determining the wear comfort of mold brassieres.