• Applied Chemistry for Engineering
• /
• v.20 no.5
• /
• pp.511-516
• /
• 2009

Photodegradation characteristics of polyolefin composites were studied. Thermogravimetric analysis results suggest that the polyolefin blends used in this study have different amounts of talc. The mechanical behaviors of polyolefin blends, which experienced UV-irradiation in accordance with SAE J1960, are investigated using tensile and Izod impact tests. These results show that as the UV-exposure time increases, a significant drop in the elongation at break and impact strength at a low temperature are observed. This may be explained by the decreases in elastic energy derived from the scission of polymer molecular chains and the low density of entanglement after UV- photodegradation. Scanning electron microscopy observations indicate that no crack and surface damage are observed, while the additional talc particles are exposed, on the UV-exposed surfaces. The exposure of talc particles may be responsible for the discoloration of UV-exposed polyolefin blend surface. Observation using Fourier transform infrared spectroscopy (FT-IR) confirms the presence of photodegradation on the surface of UV-exposed polyolefin blend.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.425-425
• /
• 2011

The photocatalytic decomposition of toluene gas was investigated with $TiO_2$ on nano-diamond powder (NDP) under UV irradiation. Atomic layer deposition (ALD) was used for the growth of $TiO_2$ on the NDP. The structure and surface properties of catalysts were characterized by X-ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS) and Transmission Electron Microscopy (TEM). The photocatalytic activity for the toluene decomposition was evaluated by measuring the concentration change of toluene and $CO_2$ gas with gas chromatography (GC)-flame ionization detector (FID) system. The photocatalytic activities of $TiO_2$/NDP catalysts were compared with that of P-25. The rate of initial photocatalytic decomposition of toluene for the $TiO_2$/NDP catalysts was relatively lower when compared to P-25. The photocatalytic activity of P-25 was rapidly decreased with time, whereas, the deactivation of $TiO_2$/NDP catalysts was less pronounced. Therefore, as the reaction time increased, the photocatalytic activity of $TiO_2$/NDP catalysts became higher than that of P-25. The intermediates such as benzaldehyde or benzoic acid, etc were more easily adhered to the active site on the P-25 surface during reaction, resulting in easier deactivation of P-25. These results could be confirmed using FT-IR spectroscopy. We suggest that the NDP used as substrate can reduce the deactivation of $TiO_2$ on the surface.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.170-170
• /
• 2011

태양전지와 박막 트랜지스터를 위한 유망한 재료로서 수소화된 비정질 실리콘과 나노결정 실리콘 박막이 관심을 받아 왔다. 특히, 수소화된 나노결정 실리콘 박막은 비정질 대비 높은 방향성과 조밀한 구조 덕에 박막 태양전지나 TFT(Thin film transistor) 소자의 성능 향상에 기여할 수 있는 물질로 연구되고 있다. 이러한 박막들은 보통 $SiH_4$같은 Si을 포함한 가스에 다량의 $H_2$를 희석시켜 플라즈마 화학 증착법(PECVD, Plasma Enhanced Chemical Vapor Deposition)에 의해 성장된다. 이러한 CVD증착 방식을 이용하여 결정화된 박막을 얻기 위해서는 대개 높은 수소 희석비를 이용하는 것이 일반적이나, 이러한 공정 방식은 실리콘이 결합되어야 할 결합위치에 bonding energy가 더 높은 수소의 결합을 촉진하게 된다. 이러한 특성은 박막 태양전지에서 효율을 떨어뜨리는 주요 요소로 작용하고 있다.(1) 본 연구에서는 수소의 결합 확률을 낮춘 결정화된 박막을 성장시키기 위해 수소를 대신하여 헬륨을 희석가스로 사용하여 박막을 증착하고 그 특성을 분석해 보았다. 박막의 구조적 특성, 결정화도(Xc), 플라즈마 내 활성 라디칼(Active radical in plasma), Si-H결합 특성, 전도도(Conductivity)와 같은 박막 특성을 알아보기 위해 주사전자현미경(SEM, Scanning Electron Microscopy), 라만 분광기(Raman spectroscopy), 광 방출 분광기(OES, Optical Emission Spectrocopy), 적외선 분광기(FT-IR, Fourier Transform-Infrared Spectroscopy), Keithley measurement kit이 사용되었다. 수소를 대신하여 헬륨을 사용함으로써 동일 결정화도 대비 10%이상 낮은 microstructure factor 값을 얻을 수 있었으며 인가되는 RF 전력을 140W까지 증가시켰을 때 약 80%의 결정화도를 관찰할 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.459-459
• /
• 2012

Recently, the discharge of global warming gases in dry etching process of TFT-LCD display industry is a serious issue because perfluorocarbon compound (PFC) gas causes global warming effects. PFCs including CF4, C2F6, C3F8, CHF3, NF3 and SF6 are widely used as etching and cleaning gases. In particular, the SF6 gas is chemically stable compounds. However, these gases have large global warming potential (GWP100 = 24,900) and lifetime (3,200). In this work, we chose C3F6O gas which has a very low GWP (GWP100 = <100) and lifetime (< 1) as a replacement gas. This study investigated the effects of the gas flow ratio of C3F6O/O2 and process pressure in dual-frequency capacitively coupled plasma (CCP) etcher on global warming effects. Also, we compared global warming effects of C3F6O gas with those of SF6 gas during dry etching of a patterned positive type photo-resist/silicon nitride/glass substrate. The etch rate measurements and emission of by-products were analyzed by scanning electron Microscopy (SEM; HITACI, S-3500H) and Fourier transform infrared spectroscopy (FT-IR; MIDAC, I2000), respectively. Calculation of MMTCE (million metric ton carbon equivalents) based on the emitted by-products were performed during etching by controlling various process parameters. The evaluation procedure and results will be discussed in detail.

• Korean Journal of Materials Research
• /
• v.23 no.7
• /
• pp.359-365
• /
• 2013

We investigated the nanostructural, chemical and optical properties of nc-Si:H films according to deposition conditions. Plasma enhanced chemical vapor deposition(PECVD) techniques were used to produce nc-Si:H thin films. The hydrogen dilution ratio in the precursors, [$SiH_4/H_2$], was fixed at 0.03; the substrate temperature was varied from room temperature to $600^{\circ}C$. By raising the substrates temperature up to $400^{\circ}C$, the nanocrystalite size was increased from ~2 to ~7 nm and the Si crystal volume fraction was varied from ~9 to ~45% to reach their maximum values. In high-resolution transmission electron microscopy(HRTEM) images, Si nanocrystallites were observed and the crystallite size appeared to correspond to the crystal size values obtained by X-ray diffraction(XRD) and Raman Spectroscopy. The intensity of high-resolution electron energy loss spectroscopy(EELS) peaks at ~99.9 eV(Si $L_{2,3}$ edge) was sensitively varied depending on the formation of Si nanocrystallites in the films. With increasing substrate temperatures, from room temperature to $600^{\circ}C$, the optical band gap of the nc-Si:H films was decreased from 2.4 to 1.9 eV, and the relative fraction of Si-H bonds in the films was increased from 19.9 to 32.9%. The variation in the nanostructural as well as chemical features of the films with substrate temperature appears to be well related to the results of the differential scanning calorimeter measurements, in which heat-absorption started at a substrate temperature of $180^{\circ}C$ and the maximum peak was observed at ${\sim}370^{\circ}C$.

• Polymer(Korea)
• /
• v.28 no.6
• /
• pp.468-477
• /
• 2004

The polymer blends of waste poly(vinyl chloride) (RPVC) and waste polyethylene (RPE) were prepared by melt mixing. Various ethylene-vinyl acetate copolymers (EVA) and ethylene-methacrylic acid Na salt copolymer (ionomer) were used as compatibilizer. Their morphologies and mechanical properties were evaluated as a funtion of mixing sequence and time. EVA with high vinyl acetate contents showed a rapid increment of tensile properties when small amount was added. Tensile properties of the blends were gradually increased with the addition of ionomer. Morphologies of RPVC/RPE blends were analyzed by scanning electron microscopy. FT-IR data showed that EVA was a good compatibilizer in RPVC/RPE blend compared to ionomer. Mechanical properties of the blends were highly enhanced when RPVC and compatibilizer were mixed and first RPE was added later.

• Korean Journal of Materials Research
• /
• v.15 no.8
• /
• pp.508-513
• /
• 2005

[ $TiO_2-Fe_2O_3$ ] nanocomposite powders for magnetic photocatalyst were synthesized by sol-gel process, in which $TiO_2$ photocatalytic layer was formed on the surface of $\gamma-Fe_2O_3$ magnetic core. Transmission electron microscopy (TEM) observation and X-ray diffractometry (XRD) analysis revealed that$\gamma-Fe_2O_3$ nanoparticles, $10\~20nm$ in diameter, were coated by $TiO_2$ shell of 5nm in thickness and $TiO_2$ was anatase phase. Also hydroxyl group (-OH) used to decompose organic compounds was detected by Fourier transformation infrared spectrometry(FT-IR) analysis. UV-Visible spectrophotometry results showed that light absorption occurred in the wavelength range of $400\~700 nm$, and the band gap energy $(E_g)$ of powder was 1.8 eV. Finally it was found that the coercivity $(H({ci})$ and saturation magnetization $(M_s)$ of the powder were 79 Oe and 14.8 emu/g, respectively as experimental vibrating sample magnetometer (VSM) measurements.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.7
• /
• pp.455-461
• /
• 2018

Boron nitride (BN) nanofibers were fabricated using BN nanoparticles (70 nm) by electrospinning. Morphologies such as the diameter and density of the BN nanofibers are strongly influenced by the viscosity and dispersion state of the precursor solution. In this study, the precursor solution was prepared by ball milling BN nanoparticles and polyvinylpyrrolidone (PVP, Mw~1,300,000) in ethanol, which was electrospun and then calcined to produce BN fibers. High-quality BN nanofibers were well fabricated at a BN concentration of 15 wt% with their diameters in the range of 500 nm to 800 nm; the viscosity of the precursor solution was $400mPa{\cdot}S$. The calcination of the as-electrospun BN fibers seemed to be completed by holding them at $350^{\circ}C$ for 2 h considering the TGA data. The morphologies and phases of the BN fibers were investigated by scanning electron microscopy (SEM) and X-ray diffractometry (XRD), respectively; Fourier transform infrared (FT-IR) was also used for structure analysis.

• Journal of the Korean Chemical Society
• /
• v.61 no.6
• /
• pp.339-345
• /
• 2017

Carbonaceous adsorbent (CA-WTP) was prepared by heat treatment at $400^{\circ}C$ for 2 h in N2 atmosphere using waste tire powder (WTP). WTP and CA-WTP were first characterized by thermo-gravimetric analysis (TGA), energy dispersive X-ray spectrometer (EDS), scanning electron microscopy (SEM), specific surface area analysis (BET) and FT-IR spectroscopy. Then, they were tested as adsorbents for removal of Cd in water. CA-WTP exhibited much higher specific surface area and total pore volume than WTP itself and showed higher adsorption capacity for Cd. Equilibrium data of adsorption were analyzed using Freundlich and Langmuir isotherm models. It was seen that both Freundlich and Langmuir isotherms have correlation coefficient $R^2$ value larger than 0.95. The results of studies indicate that CA-WTP developed from WTP by heat treatment could be used as efficient adsorbent for the removal Cd from water.

• Corrosion Science and Technology
• /
• v.19 no.1
• /
• pp.16-22
• /
• 2020

It is important to realize that benzoate was intercalated into hydrotalcite (HTC-Bz) by the co-precipitation method. In this case, acrylic coating with 0.5 wt% HTC-Bz was deposited on carbon steel using the spin coating method. Next, the HTC-Bz structure was characterized by Field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FT-IR). In fact, an ultraviolet vision spectroscopy (UV-Vis) was used to determine the benzoate content in HTC-Bz, and the UV absorption ability of HTC-Bz. Using electrochemical techniques, water contact angle measurement, and thermal-gravimetric analysis, we compared the protective properties before and after QUV test, hydrophobicity and the thermal stability of acrylic coating containing HTC-Bz. The obtained results showed that HTC-Bz with a plate-like structure was successfully synthesized; benzoate was intercalated into the interlayer of hydrotalcite with a concentration of 28 wt%. Additionally, it was noted that HTC-Bz has an UV absorption peak at 225 nm. In conclusion, the addition of HTC-Bz enhanced the UV stability, hydrophobicity and the thermal stability of acrylic coating.