• 전산구조공학
• /
• 제8권4호
• /
• pp.17-23
• /
• 1995

Based on the present FEM study for negative Poisson's-ratio UHMWPE, the following conclusions seem expected. 1) Negative Poisson's-ratio UHMWPE transfers less stresses to the subchondral or peripheral iliac bone, compared to the conventional UHMWPE with Poission's-ratio. 2) Negative Poisson's-ratio cup reduces stresses in UHMWPE cup itself as well as metal backing, and subchondral bone. 3) The reduction in periacetabular mechanical stresses would significantly reduce the rate of fatigue failure and consequently reduce the incidence of aseptic loosening of the cup due to wear or bone resorption.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 하계종합학술대회 논문집
• /
• pp.44-47
• /
• 1989

In this paper, We analyzed the End Effect of Single-sided Linear Induction Motor by combination of Finite Element Method in Active region and 0- 1 order Boundary Element Method in Entry, Exit region.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.131.1-134
• /
• 1999

The effect of dynamic recrystallization during hot forming process was implemented to a commercial FEM code by conditioned remeshing and remapping of sate variables. A datum strain for stress compensation was determined as a strain for maximum softening rate and was able to be formulated as a function of critical strain f($\varepsilon$). The validity of remapping criterion was examined by a series of mechanical tests and microstructural observation. The application of suggested datum resulted in better estimation of load-stroke during forging processes.

• 전기학회논문지
• /
• 제56권12호
• /
• pp.2179-2183
• /
• 2007

In this paper, to produce sheet plasma with high density for ion plating, we designed magnetic circuit of ion plating device consisting of solenoid coil and rectangular permanent magnet. And, we analyzed the effects of the magnetic field distribution using FEM (Finite Element Methode). Additionally, we made a sputtering system including ion plating technique on the basis of the design and verified the possibility of the sheet plasma application for advanced sputter system.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1996년도 춘계학술대회논문집
• /
• pp.121-129
• /
• 1996

This study aimsdetecting defects for the forming precesses of X2 spline, which is designed by an industry expert. The exist process consists of 3 runs and 7 operations with 3 heat treatments. The rigid-plastic FEM analysis was carried out to design a new process and some defects were found. Thus the design was modified to get better results. it is ocnfirmed that the industry expert agree the possibility of defects derived from the FEM results.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권4호
• /
• pp.187-193
• /
• 1999

This study investigates the hysteresis phenomena of a Synchronous Reluctance Motor (SynRM) using coupled FEM and Preisach modeling. Preisach's model, which allows accurate prediction of hysteresis, is adopted in this procedure to provide a nonlinear solution. the computer simulation and experimental result for the i$\lambda$loci show the propriety of the proposed method.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.725-730
• /
• 2002

The areas around the Nam-Hae are mostly covered in thick soft clay deposits(50∼60.0m). In order to improve the ground in these areas verticals trains have been partially penetrated up to the depth of about 25.0m. However, since the predicted values of settlement have often been changed at some predicted time. Finite element analysis was performed to investigate the consolidation behaviour for it. The results from FEM was compared with various observational methods.

• 전기학회논문지
• /
• 제57권4호
• /
• pp.596-602
• /
• 2008

This paper presents the dynamic characteristic analysis of Permanent Magnet Linear Synchronous Motor(PMLSM) according to variable load. In order to analyze dynamic characteristics, finite element method(FEM) was used for calculation of the parameter and the Matlab simulink was used for dynamic characteristic simulation. The measuring system of the dynamic characteristics was manufactured and the experiment results were compared with the simulation results.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.23-24
• /
• 2010

• 소음진동
• /
• 제9권2호
• /
• pp.331-339
• /
• 1999

This paper presents the simplified formulas for calculating the fundamental frequencies of the cantilevered bellows in the axial and lateral directions. The frequencies of the bellow are evaluated based on analogies with those of the beam. It is shown that the results calculated by the simplified formulas are in good agreement with those obtained from FEM analysis and the experiment.