• 대한토목학회논문집
• /
• 제5권3호
• /
• pp.39-47
• /
• 1985

본문(本文)은 연약점토지반(軟弱粘土地盤)에 이차원성토(二次元盛土)를 할 경우 지반(地盤)의 심하(沈下) 및 변위(變位)를 FEM으로 해석(解析)하는 프로그램의 연구에 대한 결과를 보고한 것이다. 구성방정식(構成方程式)으로서는 Cam-clay, Modified Cam-clay, 탄점소성(彈粘塑性)의 3 모델에서 각각 취하여 Biot의 압밀방정식(壓密方程式)과 결합(結合)시켜 이들간의 정도(精度)를 비교(比較)하고 또한 1982년(年) Magnan 등에 의해 불(佛)의 Cubzac-les-ponts에서 시험성토(試驗盛土)를 실시(實施)하여 실측(實測)과 해석결과(解析結果)를 발표(發表)한 바 있는데 그 결과(結果)와 비교(比較)한 것이다. 그 결과(結果)는 본(本) 프로그램이 보다 더 실측치(實測値)에 가깝다는 것이 확인되고 간극수압(間隙水壓)의 처리(處理)는 Christian-Boehmer 계(系)의 FEM 해석(解析)이 그들이 사용(使用)한 Sandhu-Wilson 계(系)보다 더 실제에 가깝고 성토부(盛土部)를 유한요소화(有限要素化)하는 것이 더 정확하다고 판단된다.

• 한국생산제조학회지
• /
• 제19권1호
• /
• pp.42-49
• /
• 2010

In general, the direct experimental approach to study machining processes is expensive and time consuming, especially when a wide range of parameters are included: tool, geometry, materials, cutting conditions, etc. The aim of this study is to verify the effectiveness of finite element method for orthogonal cutting process by comparing the simulated cutting forces with measured results. Two commercialized finite element codes $AdvantEdge^{TM}$ and Deform-$2D^{TM}$ have been used to simulate the cutting forces in orthogonal cutting process. In this paper, estimated cutting and feed force components are compared with experimental results for different two materials. As a result, it has been found that FEM simulation is effective for understanding and predicting the orthogonal cutting process although some improvements on friction model and remeshing process are needed.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1994년도 추계학술대회
• /
• pp.75-78
• /
• 1994

Clinically, proximal bone resorption in the femur is frequently seen postoperatively on the follow up X-rays after total hip replacement(THR). We developed the finite element model of cementless THR. The model is two dimensional side plate model, whereby the three dimensional structural integrity of the bone can be accounted for by a separate two dimensional mesh, a side plate. The subject of this article is the development and application of this two dimensional side plate FEM to study the reverse effect of the various degree of bone resorption of femur after THR. The results of this study indicates that two dimensional side plate model is good and simple alternative to complex three dimensional model and the severity of the proximal bone resorption has the effect of more increasing stress on the cortex at the level of femoral stem tip.

• Journal of Mechanical Science and Technology
• /
• 제14권2호
• /
• pp.141-151
• /
• 2000

The purpose of this study is to develop an effective method for automated deburring of precision components. A high power laser is proposed as a deburring tool for complex part edges and burrs. For the laser experiments, rectangular-shaped carbon steel and stainless steel machined specimens with burr along one side were prepared. A 1500 Watt $CO_2$ laser was used to remove burrs on the workpieces. The prediction of the heat affected zone (HAZ) and cutting profile of laser-deburred parts using finite element method is presented and compared with the experimental results. This study shows that the finite element method (FEM) analysis can effectively predict the thermal affected zone of the material and that the technique can be applied to precision components.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.945-947
• /
• 2003

Various kinds of practical machines using single phase induction motor(SPIM) are necessary to control speed and torque. In particular, capacitor-run type SPIM has constitutional characteristics, the motor torque is changed by auxiliary capacitance variation. In this study, we manifest equivalent model having more simplicity, and study the relation between torque and capacitance value of SPIM. And analyze Magnetic vibration for FEM(Finite Element Method) simulation. Also, We design the experimental controller which is able to speed control accurately by phase angle control of AC input voltage. Through the simulation and experimental results, we confirmed validity of this study.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.184-187
• /
• 2005

Forging process is one of the forming process and is used widely in automobile parts and manufacture industry. Especially the gears like spur gear, helical gear, bevel gear were produced by machine tool, but recently they have been manufactured by forging process. The goal of this study is to study forming process with data obtained by comparison between forward extrusion and upsetting simulation results and formability improvement by various heat treatment conditions. By analysis data of 3D FEM by upsetting and forward extrusion forming, the forming process of clutch gear develops using data based on 3D FEM analysis. Through tensile test using specimens by various heat treatment conditions, the optimal heat treatment condition is obtained by comparison the results of tensile test.

• 국제초고층학회논문집
• /
• 제4권1호
• /
• pp.39-44
• /
• 2015

This paper presents the structural health monitoring (SHM) of Shanghai Tower. In order to provide useful information for safety evaluation and regular maintenance under construction and in-service condition, a comprehensive structural health monitoring (SHM) system is installed in Shanghai Tower, which is composed of a main monitoring station and eleven substations. Structural responses at different construction stages are measured using this SHM system and presented in this study. Meanwhile, a detailed finite element model (FEM) is created and comparison of results between SHM and FEM is carried out. Results indicate that the time-dependent property of concrete creep is of great importance to structural response and the measured data can be used in FEM updating to obtain more accurate FEM models at different construction stages. Therefore, installation of structural health monitoring system in super-tall buildings could be considered as an effective way to assure structural safety during the construction process.

• Tribology and Lubricants
• /
• 제22권3호
• /
• pp.119-126
• /
• 2006

In this paper, the contact behavior characteristics of a primary sealing components such as a seal ring and a seal seat has been presented for a small hydro-power turbine. Using the non-linear FEM analysis, the maximum temperature, the axial displacement, radial differences between a seal ring and a seal seat, and maximum contact normal stress have been analyzed for three optimized sealing profiles in which are designed based on the FEM analysis and Taguchi's experimental method. The three primary sealing profiles between a seal ring and a seal seat are strongly related to a leakage of a water for a hydro-power turbine and wear of a primary sealing component. The computed results show that the contact rubbing area between a seal ring and a seal seat is very important for reducing a friction heating and wear in a sealing gap, and increasing a contact normal stress in primary sealing components. Based on the FEM computation, models II and III in which have a small rubbing surface of seal rings show low dilatation of primary sealing components, and high normal contact stress between a seal ring and a seal seat. Thus, the FEM computed results recommend a short contacting width of a primary sealing component for reducing a leakage and thermal distortions, and expanding a seal life. This means that a conventional primary sealing component may be switched to a reduced sealing face of seal rings.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1035-1037
• /
• 2005

The analysis of magnetic fields(2-D) induced by line currents, such as Overhead Trolley Lines or Transmission Lines, is not so easy by using the standard Finite Element Method(FEM). Mesh generation is one of the most important processes in the standard FEM. Because, the current region is relatively small compared with whole region, and actually is a line without thickness, the mesh refinement around the source lines yields many demerits. A way of supplement such a defect, we proposed the coupling scheme of analytical solution and FEM. In this study, the analytical solution is adopted around the region of line currents and FE solution is a lied to the rest of source region. And the two types of solution are coupled at the artificial boundary. To verify the usefulness of proposed algorithm, simplified model with magnetic material in FE region is chosen and analyzed. The results are compared with those of standard FEM. And the errors between them can be reduced by increasing harmonic orders.

• 소성∙가공
• /
• 제19권2호
• /
• pp.101-106
• /
• 2010

CB100 is one of the channel type products in the steel beam. In this study, rolling process of CB100 is analyzed by 3D FEM simulation and rolling process. FEM simulation result is compared with rolling process data. Also the intermediate & finishing roll stress analysis is carried out and the suitability of the roll through roll stress resultant analysis is evaluated. In order to decrease the roll stress, new pass schedule is developed for stable load balance between intermediate and finishing rolling stand. Therefore new rolling pass schedule is verified by the analysis results of rolling process and roll stress. By the analysis results, the credibility of rolling process analysis was obtained and it was determined that the possibility of roll damage between intermediate and finishing mill was high. So the new pass schedule was developed. Through the result of rolling process and roll stress analysis, it was obtained that the reduction of roll stress and stable load balance.