• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.05a
• /
• pp.55-56
• /
• 2015

This study is corroborated as a fundamental resource to develop structural lightweight paste containing silica fume as a part of cement. Paste using foaming agent is generated much foam and decreased density of paste. This study is measured at 0.8% of foaming agent dosage but over 0.8% of foaming agent dosage raise density of paste because of interconnection with foam. Also, FEM analysis using SEM image is confirmed correspondence of between Elastic modulus of experiment and FEM analysis.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.1
• /
• pp.223-230
• /
• 2006

In this paper the method for repair LCC evaluation of reinforced concrete structures deteriorated by chloride attack was constructed. Also, the FEM analysis for chloride ion penetration into concrete was conducted to evaluate the repair LCC which was decided by the number of repair times including early stages of construction and repair construction during the service life of structures. As a result, the number of repair times is obtained from the comparing the concentration of the chloride ion in a rebar position, and the critical chloride ion concentration of rebar corrosion through the FEM analysis considering the kind of repair materials and methods. Also, the repair LCC could be calculated by the number of repair times during the service life of structures.

• Bulletin of the Korean Space Science Society
• /
• 2008.10a
• /
• pp.28.4-29
• /
• 2008

The aim of the test is to provide an experimental basis to validate the prediction of the FEM for high frequency jitter analysis due to reaction wheel. The principle is to measure structural transfer functions between the input disturbances at RWA base plate and the accelerations near the end tips of payload, in a configuration close to the operational model. The spacecraft shall have to be suspended, in order to be representative of on-orbit boundary conditions. The results of the test shall be compared to the output of the FEM analysis, and if needed, local upgrades of the FEM and/or margin policy shall be defined in order to guarantee a good test/FEM consistency. Test results were compared with the transfer functions of the FEM, which is globally tuned based on the results of vibration test and consequently have lower damping coefficients values than 1% in the frequency range of 60~200Hz. The damping coefficients estimated from the figures of FRF test results are different from the theoretical FEM, but the magnitude trend of FRF of the test results is somewhat similar with the analytical, it is expected that the overall jitter effect of final estimation is nearly same with the preliminary analysis result in which the damping coefficients were assumed to be 1% for all modes in FEM.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.6
• /
• pp.114-122
• /
• 1999

By using the FEM, a method for the stress analysis of the presented dies has been proposed. In this method, FEM and Lame equation are used for the analysis of the die insert and the stress ring, respectively. The proposed method includes the calculation of the contact pressure between the die insert and the stress ring. To show the validity, the proposed method has been applied to the simple test problem. The results of the stress analysis have been compared with the results of ANSYS, a commercial FE-code. Cold extrusion has been simulated by using the rigid-plastic FEM and the results of the deformation analysis have been used as the input of the die structure analysis. The stress states of the prestressed extrusion die have been obtained. The stress analysis of the die insert with stress rings has also been performed during extrusion.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.68-74
• /
• 1998

The ESPI(Electronic Speckle Pattern Interferometry) is a real time, full-field, non-destructive optical measurement technique that allows static and dynamic deformation analysis and surface shape measurements of engineering structures. e .g. turbine blades. vehicle engine components, body panels, etc. This technique is very similar to holographic interferometry, but uses a solid static camera and an image processing board for recording and digital processing of speckle patterns. In this paper it is presented that FEM results for the free vibration of symmetrically laminated composite as [30/-30/90]s. The natural frequencies of laminated composite rectangular plates having the particular boundary condition are experimentally obtained. In order to demonstrate the validity of the experiment, FEM analysis using ANSYS was performed and natural frequencies experimentally obtained is compared with calculation by FEM analysis. The results obtained from both experiment and FEM analysis show a good agreement.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.4
• /
• pp.498-503
• /
• 2010

The main purpose of this study strongly concerned micro machining error estimation by using FEM analysis of tool deflection shapes in micro flat end-milling process. For the precision micro flat end-milling process, analysis of micro cutting errors is mandatory. In general, tool deflection is a major factor which causes cutting error and limits realization of the high-precision cutting process. Especially, in micro end-milling process, micro tool deflection generates very serious problems in contrast to macro tool deflection. Methods which deal with compensation of cutting error by tool deflection in macro end-milling process have been studied plentifully but, few researches transact with micro scaled cutting tool deflection in micro cutting process. Therefore, the trend of micro tool deflection was estimated by using FEM analysis in this paper. Cutting forces were acquired by micro dynamometer and these were utilized in FEM analysis. In order to verify FEM analysis results, micro machining processes were carried out and real machined profiles were compared with FEM results. Finally through the proposed approach well suited FEM results were obtained.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.401.2-401
• /
• 2002

An unconstrained tuning fork with a 3-D model has been numerically analyzed by Finite Element Method (FEM) and Boundary Element Method (BEM). The first three natural frequencies were calculated by the FEM modal analysis. Then the change of the modal frequencies was examined with the variation of the tuning fork length and width. (omitted)

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.19-30
• /
• 2014

In this study nonlinear FEM analysis for steel pylon base of a cable supported bridge is performed in order to compare the results of Akashi-Kaikyo bridge's design specification established in 1970. Due to convenience of its application, the Akashi grand bridge's design specification has been applied to the base design of cable stayed bridges. It has been using linear spring in order to model prestressed high tensioned bars between steel pylon bottom plates and the base concrete. However, the results of nonlinear FEM analysis revealed that the Akashi-Kaikyo bridge's design specification has various problems in the analysis of the steel pylon base. And the steel pylon base has various complex members connecting with each other, and it is main member to resist against the wind load or the earthquake load. Therefore, the nonlinear FEM analysis has to be conducted in order to predict the behavior of steel pylon base exactly. Also, the nonlinear FEM analysis is more reasonable for the load and resistant factor design.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.335-338
• /
• 2003

Flexural test and parametric study by FEM analysis on 6.0m long reinforced concrete beams strengthened by GFRP are reported in these tests. The selected variables are strengthened plate length, plate thickness. The effects of these variables are discussed. The results generally indicate that the flexural strength of strengthened beams is increased. The results of FEM analysis show that the more strengthening GFRP is the more stress of GFRP is decrease when failure mode is peeling failure.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.388-392
• /
• 1995

The Electronic Speckle Pattern Interferometry(ESPI) has been applied to many technical problems such as deformation and displacement measurement, strain visualization and surface roughness monitoring. Composite materials have various complicated characteristics depending on the ply materials,ply orientations,ply stacking sequences and boundary conditions. Therefore, it is difficult to analyze composite material. For efficient use of composit materials in engineering applications, the dynamic behavior such as, natural frequencies and modal patterns should be identified. This studying presents FEM results for the free vibration of symmetrically laminated composite as [30/-30/90] $_{s}$. The natural frequencies of laminated composite rectangular plates having the boundary condition(:2-edge clamped) are experimentally obtained. In order to demonstrate the validity of the experiment,FEM analysis using ANSYS was performed and natural frequencies experimentally obtained is compared with calculated by FEM analysis. The results obtained from both experiment and FEM analysis show a good agreement.t.