• 소성∙가공
• /
• 제13권6호
• /
• pp.490-496
• /
• 2004

Springback comes from the release of external loads after forming. The control of phenomenon is especially important in the sheet metal forming since there are no other practical methods available to correct the dimensional inaccuracy from springback. Therefore the accurate prediction before the die machining has been a long goal in the field of sheet metal forming. The am of the present study is to enhance the prediction capability of finite element (FE) analysis for the springback phenomenon. For this purpose FE analysis for V-bending has been carried out with the commercial programs, LS-DYNA. The FE analysis results have been validated through the comparison of experimental. The experimental results measured directly by the strain gauge have given the confidence to FEA.

• Safety and Health at Work
• /
• 제12권4호
• /
• pp.544-545
• /
• 2021

The article by Tae-Gu Kim et al. conducted elastic FE modeling, which was inappropriate for fracture of elastic-plastic chain material (11.3% of elongation). FE analysis results and the findings in the fracto-graphic analysis did not tally but contradicted each other. The article identified "incorrect installation"/bending forces as the root cause while FE results of the chain under bending forces showed very low stresses at fracture locations but the highest stress in the middle of shank of the chain. The article's "step-like topographies indicating the fracture due to bending moment rather than uniaxial tension" lacked scientific support. The load value carried by each chain section under bending/incorrect installation was only half of that under tension, thus the article using same load value in FE simulation comparison for bending and tension was incorrect. The real cause of the chain fracture was likely improper checking the lifted load or/and using the wrong chain with much lower safety working load.

• 한국주조공학회지
• /
• 제30권3호
• /
• pp.100-110
• /
• 2010

The solidification sequence and formation of intermetallic phase of Fe-rich Al-Si-Cu alloy were investigated by using real-time imaging of synchrotron X-ray radiation. Effects of cooling rate during uni-directional solidification on the resultant solidification behavior was also studied in a specially constructed vacuum chamber in the SPring-8 facility. The series of radiographic images were complementarily analyzed with conventional analysis of OM and SEM/EDX for phase identification. Detailed solidification sequence and formation mechanisms of various phases were discussed based on real-time image analysis. The growth rates of $\alpha$-AlFeMnSi and ${\beta}-Al_5FeSi$ were measured in order to understand the growth behavior of each phase. It is suggested that real-time imaging technique can be a powerful tool for the precise understanding of solidification behavior of various industrial materials.

• Structural Engineering and Mechanics
• /
• 제19권1호
• /
• pp.97-106
• /
• 2005

The standard practice is to seismically qualify the safety related equipment and structural components used in the nuclear power plants. Among several qualification approaches the qualification by the analysis using finite element (FE) method is the most common approach used in practice. However the predictions by the FE model for a structure is known to show significant deviations from the dynamic behaviour of 'as installed' structure in many cases. Considering such limitation, few researchers have advocated re-qualification of such structures after installation at site to enhance the confidence in qualification vis-$\grave{a}$-vis plant safety. For such an exercise the validation of FE model with experimental modal data is important. A validated FE model can be obtained by the Model Updating methods in conjugation with the in-situ experimental modal data. Such a model can then be used for qualification. Seismic analysis using the updated FE model and its advantage has been presented through an example of an in-core component - a perforated horizontal tube of a nuclear reactor.

• 한국환경과학회지
• /
• 제26권12호
• /
• pp.1333-1339
• /
• 2017

Coal-fired power plants emit various Particulate Matter(PM) at coal storage pile and ash landfill as well as the stack, and affect the surrounding environment. Field Emission Scanning Electron Microscopy and Energy Dispersive X-ray analyzer(FE-SEM/EDX) were used to develop identification factor and the physico-chemical analysis of PM emitted from a power plant. In this study, three samples of pulverized coal, bottom ash, and fly ash were analyzed. The pulverized coal was spherical particles in shape and the chemical composition of C-O-Si-Al and C/Si and C/Al ratios were 200~300 on average. The bottom ash was spherical or non-spherical particles in shape, chemical composition was O-C-Si-Al-Fe-Ca and C/Si and C/Al ratios were $4.3{\pm}4.6$ and $8.8{\pm}10.0$. The fly ash was spherical particles in shape, chemical composition was O-Si-Ai-C-Fe-Ca and C/Si and C/Al ratios were $0.5{\pm}0.2$ and $0.8{\pm}0.5$.

• Computers and Concrete
• /
• 제24권3호
• /
• pp.237-247
• /
• 2019

The key issue for the finite element analysis (FEA) of section steel reinforced concrete (SRC) structure is how to consider the bond-slip performance. However, the bond-slip performance is hardly considered in the FEA of SRC structures because it is difficult to achieve in the finite element (FE) model. To this end, the software developed by Python can automatically add spring elements for the FE model in ABAQUS to considering bond-slip performance. The FE models of the push-out test were conducted by the software and calculated by ABAQUS. Comparing the calculated results with the experimental ones showed that: (1) the FE model of SRC structure with the bond-slip performance can be efficiently and accurately conducted by the software. For the specimen with a length of 1140 mm, 3565 spring elements were added to the FE model in just 6.46s. In addition, different bond-slip performance can also be set on the outer side, the inner side of the flange and the web. (2) The results of the FE analysis were verified against the corresponding experimental results in terms of the law of the occurrence and development of concrete cracks, the stress distribution on steel, concrete and steel bar, and the P-S curve of the loading and free end.

• 대한화학회지
• /
• 제55권3호
• /
• pp.463-471
• /
• 2011

[ $N_2O_2$ ] 시프염기 리간드인 N,N'-bis(4-methoxysalicylidene) phenylendiamine(4-$CH_3O$-salphen)을 합성하였다. 분광광도법으로 4-$CH_3O$-salphen을 이용하여 수용액 중의 Fe(II)와 Fe(III)이온의 분리 정량실험을 위하여, 리간드 농도는 $4.0{\times}10^{-4}\;M$, DMF 용매와 물의 비율은 70/30(v/v), pH는 3.4~3.8 범위, 온도는 $55^{\circ}C$에서 1 시간 정도를 물 중탕하여 결과를 얻었다. 시료의 예비 산화 및 환원 전처리는 $5.0{\times}10^{-4}\;M$ 농도의 $H_2O_2$와 $NH_2OH{\cdot}HCl$을 사용하여 단일 원자가 상태의 시료를 만들어 사용하였다. 이때 Fe(II)와 Fe(III) 이온의 정량은 434 nm와 456 nm에서 흡광도를 측정하였다. 이상의 최적화된 실험조건을 이용하여 약수, 온천수, 바닷물 및 하수 처리장의 처리수를 채취하여 Fe(II)와 Fe(III) 이온을 각각 정량 분석한 결과는 측정 평균값이 표준 값에 대하여 2.00~6.90% 범위에서 잘 일치 하였고, 정량검출한계는 Fe(II)의 경우 27.9 ng/mL이었고, Fe(III)은 55.8 ng/mL이었다.

• Bulletin of the Korean Chemical Society
• /
• 제18권7호
• /
• pp.743-749
• /
• 1997

Local structure refinement of the BaFe1-xSnxO3-y system (x=0.00-0.50) has been carried out with Fe K-edge x-ray absorpion spectroscopic studies. It is found out that the Fe ions are placed in two different symmetric sites such as tetrahedral and octahedral sites in the compounds by comparison with Fe K-edge x-ray absorption near edge structure (XANES) spectrum of the γ-Fe2O3 compound as a reference. Small absorption peaks of dipole-forbiden transitions appear at a pre-edge region of 7111 eV due to the existence of Fe ions in the tetrahedral and octahedral sites. The peak intensity decreases with the substitution amount of Sn ion. Three different absorption peaks of 1s→4p dipole-allowed transition appear on the energy region between 7123 and 7131 eV. The peaks correspond to 1s→4p main transition of Fe ions in tetrahedral and octahedral sites and 1s→4p transition followed by the shakedown process of ligand to metal charge transfer. The bond distances between Fe ions in the tetrahedral site and nearest neighboring oxygen atom (Fe-4O), and those in octahedral site (Fe-6O) are determined with the extended x-ray absorption fine structure (EXAFS) analysis. Two different interatomic distances increase with the substitution amount of Sn ion and also the bond lengths of Fe-4O are shorter than those of Fe-6O in all compounds.

• 한국자기학회지
• /
• 제8권2호
• /
• pp.67-73
• /
• 1998

perovskite Gd1-xSrxFeO3-y(x=0.0, 0.5) 시료의 결정학적 및 자기적 성질을 X-ray 회절과 Mossbauer 분광법 및 VSM를 이용하여 연구하였다. 결정 구조는 모두 orthorhormcis 구조를 가지며 Gd0.5Sr0.5FeO3-y의 격자상수는 a0=5.53$\AA$, bo=5.608$\AA$, C0=7.724$\AA$이었다. Gd1-xSrxFeO3-y(x=0.0, 0.05,)의 Mossbauer 실험을 4.2K부터 690K 온도 영역에서 수행하였고 Neel 온도는 GdFeO3 는 690K로 Gd0.5Sr0.5FeO3-y는 515K로 결정 하였다. GdFeO3 시료의 이온 상태는 Fe3+임을 알 수 있었고 Brillouin 함수값S=5/2를 만족하며 팔면체 자리를 나타내고 있다. Mossbauer spectrum과 Mohrdua 분석에 의해 Gd0.5Sr0.5FeO3-y 시료는 Fe3+와 Fe4+이온이 공존하여 존재합을 알았다.

• 한국진공학회지
• /
• 제11권4호
• /
• pp.240-248
• /
• 2002

결정성이 좋을 것으로 기대되는 Fe이 도핑된 $Fe_{x}Ti_{l-x}O_2$박막 (x=0.07과 0.16)을 rutile $TiO_2$(110) 기판위에 산소 플라즈마 적층 성장 방법으로 성장시켰다. 도핑되는 Fe의 함량에 따른 표면 특성을 규명하기 위하여 박막 성장은 같은 조건에서 이루어졌다. 여러 가지의 표면분석법을 이용하여 성장된 박막의 표면 특성을 규명하였다. $Fe_{x}Ti_{l-x}O_2$박막에 존재하는 Ti의 산화상태는 +4 이었고 Fe의 경우는 +2와 +3의 산화상태가 섞여있었으며 Fe의 함량이 높은 $Fe_{0.16}Ti_{0.84}O_2$박막에서 $Fe^{3+}$ 이온의 함량이 더 높은 것으로 나타났다. $Fe_{0.07}Ti_{0.93}O_2$박막은 기판과 유사한 평탄한 표면에 막대형과 원통형의 높은 island 형태로 성장되었다. $Fe_{0.16}Ti_{0.84}O_2$박막은 $Fe_{0.07}Ti_{0.93}O_2$ 박막보다는 평탄하지만 적은 island들이 뭉쳐있는 다소 거칠은 표면을 한 다결정성 형태로 성장되어 Fe의 함량에 따라 morphology가 다르게 나타났다.