• 한국화재소방학회논문지
• /
• 제5권1호
• /
• pp.23-28
• /
• 1991

This paper is concerned with the numerical analysis of the temperature of steel columns when they are exposed to flame of a fire temperature curve in order to test resistivity against the fire. In this stuer a 2-dimensional heat conduction FDM was developed to predict the temperature dustribution of steel column under various construction conditions. A proposal to estimate the influence of free water content in the insulation also made.

• 한국분말재료학회지
• /
• 제3권1호
• /
• pp.25-32
• /
• 1996

Flying and solidification behaviors of the particles manufactured by centrifugal atomization were investigated. Both models were solved by the explicit FDM. Flying calculation supported the experimental results that the finer particles flied shorter than coarser particles and that particles flied shorter for lower rotation velocity than for higher velocity. Cooling curve and dendrite arm spacing were predicted by use of heat transfer analysis.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.235-242
• /
• 2000

In this paper, the dynamic characteristics of coupled herringbone groove journal bearings and spiral groove thrust bearings with conical motion were numerically analyzed, The bearing performance characteristics were calculated by the perturbation method and are solved by FDM. Stability of bearing was obtained from the threshold of instability.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.1089-1094
• /
• 2004

Numerical methods to estimate behaviors of jointed rock mass can be roughly divided into two method : discontinuous model and continuum model. Generally, distinct element method (DEM) is applied in discontinuous model, and finite element method (FEM) or finite difference method (FDM) is utilized in continuum model. To predict a behavior of discontinuous model by DEM, it is essential to understand characteristics of joints developed in rock mass through field tests. However, results of field tests can not provide full information about rock mass because field tests is conducted in limited area. In this paper, discontinuous analysis by UDEC and continuous analysis by FLAC is utilized to estimate a behavior of a tunnel in jointed rock mass. For including discontinuous analysis in continuous analysis, joints in rock mass is considered by reducing rock mass properties obtained by RMR and decreasing shear strength of rock mass. By comparing and revising two analysis results, analysis results similar with practical behavior of a tunnel can be induced and appropriate support system is decided.

• Wind and Structures
• /
• 제23권6호
• /
• pp.615-639
• /
• 2016

Although the underlying mechanism of rain-wind induced vibrations (RWIVs) of stay cables has not been fully understood, some countermeasures have been successfully applied to mitigating this kind of vibration. Among these, installing dampers near the bridge deck was widely adopted, and several field observations have shown its effectiveness. In this study, the effectiveness of dampers to RWIVs of stay cables is numerically investigated comprehensively by means of finite difference method (FDM). Based on the free vibration analysis of a taut string, it is found that the 3-points triangle scheme, which can be easily implemented in FDM, can offer an excellent approximation of the concentrated damping coefficient (expressed as a Dirac delta function) at the location where the damper is installed. Then, free vibration analysis of a 3-D continuous stay cable attached with two dampers is carried out to study the relationship of modal damping ratio and damping coefficient of the dampers. The effects of orientation of the dampers and cable sag on the modal damping ratio are investigated in detail. Finally, the RWIV response of a 3-D continuous stay cable attached with two dampers is examined. The results indicate that 0.5% of damping ratio is sufficient to reduce the RWIV vibration of the Cable A20 on the No.2 Nanjing Bridge over Yangtze River.

• 한국터널지하공간학회 논문집
• /
• 제4권3호
• /
• pp.185-193
• /
• 2002

본 연구에서는 풍화토층에 굴착된 지하철 터널의 변형거동과 종방향 지보재의 보강효과가 3차원 유한차분해석에 의해 조사되었다. 굴착방법이 터널 변형거동에 미치는 영향을 조사하기 위해서 반단면 및 전단면의 2가지 굴착방법이 고려되었다. 또한, 우산형 막장보강법 (RPUM) 및 유리섬유 파이프의 보강효과가 비교되었다. 터널 변형거동을 분석하기 위해 막장변위, 내공변위, 선행변위 및 측벽변위가 조사되었고, 굴착방법 및 종방향 지보재의 효과가 지표침하량를 사용하여 분석되었다. 해석 결과, 반단면 굴착이 전단면 굴착 보다 더 큰 내공변위, 선행변위, 측벽변위를 야기시키며, 반면 막장변위는 전단면 굴착이 반단면 굴착에 비해 더 크게 발생됨을 알았다. 또한, 같은 굴착방법에서는 RPUM만이 사용되었을 때가 RPUM이 유리섬유 파이프와 같이 사용되었을 때 보다 모든 변위가 더 켜졌다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.340-343
• /
• 2007

In this paper, we present our method to reduce vibration of the base plate of a refrigerator by avoiding resonance between base plate and compressor operation. To verify the modes of the base plate, FE models of the base plate with free-free condition and applied boundary condition were built and validated by results from experimental modal analysis. Operating Deflection Shape analysis was applied to find the sensitive area on the base plate during compressor operation. In optimization process, Finite Difference Method - based sensitivity analysis is used to detect the most sensitive area. Finally, based on this numerical result, we will make beads on the base plate to reduce vibration of refrigerator.

• Journal of Welding and Joining
• /
• 제16권3호
• /
• pp.141-147
• /
• 1998

Design sensitivity analysis of a vehicle system is an essential tool for design optimization and trade-off studies. Most optimization algorithms require the derivatives of cost and constraint function with respect to design in order to calculate the next improved design. This paper presents an efficient algorithm application for the design sensitivity analysis, using the direct differentiation method. A mounting area of suspension that welded on chassis frame is analyzed to show the validity and the efficiency of the proposed method. A mounting area of suspension that welded on chassis frame is analyzed to show the validity and the efficiency of the proposed method.

• 터널과지하공간
• /
• 제7권1호
• /
• pp.58-64
• /
• 1997

A pilot plant of underground cold storage for food has been excavated as a R&D program. For the stability assessment of underground cold storage opeinengs in shallow jointed rocks, three kinds of stability problems were analyzed by numerical methods. For the analysis of unstability by rock block movements, DEM was used considering the statistical distribution of rock joints. Concerning thermally induced cracking, FDM was used with thermomechanical stress analysis. Finally, in order to evaluate the joint failure during the thawing process, BE algorithm was applied. Numerical examples applied for the pilot plant show that the possibility of unstable failure of opeings exists but can be avoided with proper rock reinforcements provided.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.547-550
• /
• 2005

In many machines handling lightweight and flexible media, such as automated teller machines and printers, the media must transit an open space. It is important to predict the static and dynamic behavior of the sheets with a high degree of reliability The nonlinear theory of the dynamic elastica has often been used to a nonlinear dynamic deflection model. In this paper, the governing equation is derived and simulated by the finite difference method. The analysis has to include aerodynamic effect for more exact behavior analysis, because the flexible media can be deformed drastically by a little force. Therefore aerodynamic force must be applied to the governing equation. Different results were obtained with and without aerodynamic effect and the resulted show that after contacting circular guide, the directions of flexible media of two cases are different.