• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.325-328
• /
• 2004

This paper deals with void crushing behavior by ingot forging process which consists of sequential operations of upset forging and bloom forging. The predicted results of void crushing behavior by the simplified global-local method using F.E. analysis showed that the inherent void at the top region of the ingots remains incompletely crushed even after several forging operations. From the results of the hot upset forging test using the billets with drilled voids, it was found that the bonding efficiency of the void after forging process increases with an increase in deformation, and a decrease of initial diameter of voids.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.7
• /
• pp.723-734
• /
• 1992

In this paper, the characteristics of IPMSM(Interior-type Permanent Magnet Synchronous Motor) are simulated using 2-D. finite element method. This paper deals with the following characteristics : air gap flux density considering skew, back e.m.f., torque and inductance. Back e.m.f. is calculated using the flux obtained from the vector potential of FEM solution. Torque is calculated using improved Maxwell stress tensor method and current angle which is obtained from the controller. Direct axis inductance and quadrature axis inductance are also calculated using energy perturbation method. Computed results are found in satisfactory agreement with experimental ones. This method also can be applied for the computation and analysis of the characteristics of SPMSM, current-excited synchronous motor and reluctance motor.

• Proceedings of the KIEE Conference
• /
• 2000.11b
• /
• pp.250-252
• /
• 2000

A simple analysis method for inverter-fed induction motor using F.E.M and equivalent circuit is proposed. And an optimum shape of rotor slot for 2Hp inverter-fed induction motor is determined by combining the proposed analysis method and an optimization algorithm. Conjugate gradient method is used for the optimization algorithm. The optimization is performed for higher efficiency and reduction of harmonic loss in the inverter-fed induction motor. The optimization results are verified by comparing with those of the time-step F.E.A and the experiment.

• Nuclear Engineering and Technology
• /
• v.53 no.10
• /
• pp.3127-3132
• /
• 2021

Feasibility study of burn-up analysis and monitoring using delayed fast neutrons was investigated at Missouri University of Science and Technology Reactor (MSTR). Burnt and fresh fuel elements were used to collect delayed fast neutron data for different power levels. Total reactivity varied depending on the burn-up rate of fuel elements for each core configuration. The regulating rod worth was 2.07E-04 𝚫k/k/in and 1.95E-04 𝚫k/k/in for T121 and T122 core configurations at 11 inch, respectively. Delayed fast neutron spectrum of F1 (burnt) and F16 (fresh) fuel elements were analyzed further, and a strong correlation was observed between delayed fast neutron emission and burn-up. According to the analyzed peaks in burnt and fresh fuels, reactor power dependency was observed and it was determined that delayed neutron provided more reliable results at reactor powers of 50 kW and above.

• Wind and Structures
• /
• v.38 no.1
• /
• pp.59-74
• /
• 2024

Large Eddy Simulation (LES) is used to explore the influence of vibration frequency and amplitude on the aerodynamic performance of a rectangular cylinder with an aspect ratio of B/D=5 (B: breadth; D: depth of cylinder) at a Reynolds number of 22,000 near resonance frequency. In smooth flow conditions, the research employs a sequence of three-dimensional simulations under forced vibration with diverse frequency ratios f_e / f_o = 0.8-1.2 (f_e : oscillation frequency; f_o : Strouhal frequency when the rectangular cylinder is stationary ) and oscillation amplitudes A_h/D = 0.05 - 0.3. The individual influences of f_e / f_o and A_h/D on the characteristics of integrated and distributed aerodynamic forces are the focal points of discussion. For the integrated aerodynamic force, particular emphasis is placed on the analysis of the dependence of velocity-proportional component C₁ and displacement-proportional component C₂ of unsteady aerodynamic force on amplitude and frequency ratio. Near the resonance frequency, the dependencies of C₁ and C₂ on amplitude are stronger than that of frequency ratio. For the distributed aerodynamic force, the increase in frequency and amplitude promotes the position of the main vortex core and reattachment to the leading edge in the streamwise direction. In the spanwise direction, vibration enhances the spanwise correlation of aerodynamic force to weaken the three-dimensional effect of the flow field, and a lower frequency ratio and larger amplitude amplify this effect.

• Proceedings of the KSPS conference
• /
• 1996.10a
• /
• pp.514-514
• /
• 1996

Igbo, a new Benue Congo language has a vowel harmony system which, like that of Akan, is based on the pharynx size or tongue root position. In this study we examine Igbo vowel harmony with particular reference to assimilatory patterns of vowels in different harmony sets. This is to gain some insight into the factors involved in Igbo vowel assimilation, and to establish to what extent reports on Akan vowel assimilation are validated in Igbo. Tokens of the eight phonemic vowels of Standard Igbo are recorded from three native speakers of Igbo. The vowels are acoustically investigated (using the LPC analysis of CSL) in individual lexical items and within carefully designed carrier phrases. The F1 and F2 values of the vowels are obtained as these formant values are generally useful in establishing the salient characteristics of vowels. Vowels from the harmony sets are juxtaposed in the carrier phrases to ascertain the extent of assimilation. Results of the investigation show that the F1 values, to a large extend, are enough to characterize these vowels. The (-Expanded) vowels have higher F1 values than their (+Expanded) counterpart. Where there is an overlap in F1 values for some vowels the F1 bandwidth values serve to distinguish between the vowels. The overlap often reported in Akan for /I/ and /e/ on the one hand and /${\mho}$/ and /o/ on the other is not validated in Igbo. While the F1 values for these pairs of vowels are quite similar for one of our speakers, there is an appreciable difference between the F1 values of these vowels for the other two speakers. There is however an overlap for /e/ and /o/ for one of the speakers. Assimilations are generally regressive across word boundaries. It is, however, necessary to point out that the general perceptual impression that one of the vowels completely assimilates to the other, is not borne out by our investigation. Most of our F1 and F2 values for the vowels in individual lexical items are altered in assimilations. This then suggests that assimilation involving these vowels is partial rather than complete. The emerging 'allophones' are acoustically similar to the (+Expanded) vowel involved in the assimilation, that is when vowels from different harmony sets are involved. We conclude that while assimilation of Igbo vowels involves some phonological considerations, phonetic factors appear to be permanent in deciding the final form of the vowels.

• Journal of IKEEE
• /
• v.27 no.4
• /
• pp.399-404
• /
• 2023

In this paper, we analyzed the current path in the O/N/O (Oxide/Nitride/Oxide) structure of 3D NAND Flash memory and in the O/N/F (Oxide/Nitride/Ferroelectric) structure where the blocking oxide is replaced by a ferroelectric. In the O/N/O structure, when V_read is applied, a current path is formed on the backside of the channel due to the E-fields of neighboring cells. In contrast, the O/N/F structure exhibits a current path formed on the front side due to the polarization of the ferroelectric material, causing electrons to move toward the channel front. Additionally, we performed an examination of device characteristics considering channel thickness and channel length. The analysis results showed that the front electron current density in the O/N/F structure increased by 2.8 times compared to the O/N/O structure, and the front electron current density ratio of the O/N/F structure was 17.7% higher. Therefore, the front current path is formed more effectively in the O/N/F structure than in the O/N/O structure.

• Elastomers and Composites
• /
• v.53 no.4
• /
• pp.213-219
• /
• 2018

The degradation mechanism and physical properties of an FKM O-ring were observed with thermal aging in this experiment. From X-ray photoelectron spectroscopy (XPS) analysis, we could observe carbon (285 eV), fluoro (688 eV), and oxygen (531 eV) peaks. Before thermal aging, the concentration of fluoro atoms was 51.23%, which decreased to 8.29% after thermal aging. The concentration of oxygen atoms increased from 3.16% to 20.39%. Under thermal aging, the FKM O-ring exhibited debonding of the fluoro-bond by oxidation. Analysis of the C1s, O1s, and F1s peaks revealed that the degradation reaction usually occurred at the C-F, C-F2, and C-F3 bonds, and generated a carboxyl group (-COOH) by oxidation. Due to the debonding reaction and decreasing mobility, the glass transition temperature of the FKM O-ring increased from $-15.91^{\circ}C$ to $-13.79^{\circ}C$. From the intermittent CSR test, the initial sealing force was 2,149.6 N, which decreased to 1,156.2 N after thermal aging. Thus, under thermal aging, the sealing force decreased to 46.2%, compared with its initial state. This phenomenon was caused by the debonding reaction and decreasing mobility of the FKM O-ring. The S-S curve exhibited a 50% increase in modulus, with break at a low strain and stress state. This was also attributed to the decreasing mobility due to thermal aging degradation.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.505-510
• /
• 2002

The Friction Stir Welding (FSW) is a new joining method that was developed at The Welding Institute (TWI) in England in 1991. It applied heating by the rotational friction and material plastic flow. It was developed as a new joining method to solve the problems of epochally in the welding of Al alloys. In the study, 6000series of Alloy composed of AI-Mg-Si, one of the Al alloys that are utilized for shipbuilding and construction, is selected as a specimen and the numerical is executed against the welded zone of FSW. The material used in this study had the unique properties of strength and anti-corrosion, but since the welded joint of this material is easily softened by the welding heat, FSW is executed and the numerical analysis is carried out around the joint. To examine the mechanical behaviors and properties, F.E.M analysis is executed and the developed thermal-elastic-plastic [mite analysis are used.

• Speech Sciences
• /
• v.14 no.1
• /
• pp.63-72
• /
• 2007

In this study, the researchers evaluate the hypothesis that the reaction time (RT) in the brain is largely dependent on age and gender. The researchers tested English and Korean words using two types: reading as visual stimuli, and listening as auditory stimuli. The E-Prime program installed in functional magnetic resonance imaging (f-MRI) was used. There are 136 Korean subjects in three groups: 30 children (5th and 6th grade elementary school students), 76 young adults (college students), and 30 adults (35-53 years old). In the listening test, the variation for the two languages was different among the three age groups, regardless of gender, whereas the data did not show meaningful differences in the reading test. The findings will provide some meaningful information regarding perception and acquisition of a foreign language.