• 한국정밀공학회지
• /
• 제21권7호
• /
• pp.179-184
• /
• 2004

In this work, a copper-clad aluminum composite was fabricated using hot hydrostatic extrusion with various extrusion ratios (8.5, 19, 49) and semi-die angles (30, 45, 60 degree) at a temperature of 32$0^{\circ}C$, Material characteristics of copper-clad aluminum composites were determined from compression tests and hardness tests The results showed that for ER of 8.5, the optimum semi-die angle was below or equal to 30 degree and a pressure drop was about 31%. For ER of 19, the optimum semi-die angle was in the range of 40 to 50 degree and a pressure drop was about 38%. In the case of ER=49, the optimum semi-die angle was above or equal to 60 degree and a pressure drop was about 36%. Compressive yield strength was maximum for ER of 8.5 and semi-die angle of 30 degree and the value of maximum was 155 MPa. Uniform hardness distribution was obtained as the extrusion ratio increases and the semi-die angle decreases. In the case of ER=8.5 and semi-die angle of 30 degree, the lowest extrusion pressure and the maximum compressive yield strength was obtained. Therefor, it was concluded that the optimum extrusion condition for fabricated copper-clad aluminum composites under hydrostatic pressure environment was ER of 19 and semi-die angle of 30 degree.

• 소성∙가공
• /
• 제14권1호
• /
• pp.14-20
• /
• 2005

To carry out perfectly the forming analysis of the extruding products, it is necessary that the friction boundary condition between dies and blanks should be worked out the accurate numerical friction models. But, the existing numerical models of the extrusion may be large different from the actual conditions. In this study, accurate analysis of the extrusion forming for the variation of pressure and velocity should be subjected. It is to develop the accuracy of the numerical friction models and potentialize to apply for the high speed forming work in the extrusion. Therefore, the results should improve the accuracy, cause the energy saving for the extrusion and finally expand the applying areas of the results.

• 소성∙가공
• /
• 제1권1호
• /
• pp.52-65
• /
• 1992

In this study a new simplified three-dimensional numerical method and the associated computer program have been developed to simulate the non-axisymmetric extrusion processes. The two-dimensional rigid-plastic finite element method under the generalized plane-strain condition is combined with the slab method. To define the die geometry for a non-axisymmetric extrusion. area mapping technique was used. Streamlined die surface was used to minimize the total extrusion pressure. Extrusion of square, hexagonal and 'T' section from round billet have been simulated and experimented with a model material. The computed results were in good agreement with the experiments in cross-sectional grid distortion. Computational results will be valuable for designing tool geometries and corresponding processes.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.236-239
• /
• 1995

In this paper,Upper bound analysis to predict the formation of corner cavity during the final stage of backward extrusion is used. The critical condition for corner cavity formation is obtained by upper bound analysis. The quantitive relationships between corner cavity formation and process parameters are studied. To broaden forming limit area, driven container and multi-step forming process is proposed. As a result of FEM, forming limit is enlarged. And this results is compared with the analytric results

• 한국식품영양학회지
• /
• 제7권2호
• /
• pp.137-143
• /
• 1994

To optimize extrusion cooking condition of single screw extuder for production of puffed rice extrudate using response surface methodology (RSM), moisture content, barrel temperature and screw speed were determined from contour maps, showing relationship between dependent (hardness, expansion ratio, water absorption index, water solubility Index, degree of gelatinization) and independent variables. Optimum operational conditions for production of puffed rice extrudate with suitable quality properties were moisture content 17%, barrel temperature 1$25^{\circ}C$ and screw speed 210 rpm, respectively.

• 한국약용작물학회지
• /
• 제22권5호
• /
• pp.349-362
• /
• 2014

This study was designed to maximize extract yields of functional components in Angelica gigas Nakai by extrusion process. In addition, the optimizing condition of the extrusion process was established to increase the extraction of the functional components in A. gigas. The total polyphenol was increased by 40% compared to a control. And the optimizing condition was that the screw speed was 62.76 rpm, the amount of A. gigas powder was 34.79 kg/h, and the amount of water was 4.44 kg/h. The result of antioxidant activities of A. gigas extrusion, the inhibition of oxidization had the effect of 10.29 ~ 14.59% compared to a control. The content of decursin and decursinol angelate, which were index components, was 6.37%; it was increased by 16.64% compared to a control (5.31%) and showed a significantly difference (p < 0.05). And the optimizing condition was the screw speed 93.71 rpm, the amount of A. gigas powder was 28.67 kg/h, and the amount of water was 9.9 kg/h.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.97-101
• /
• 2001

Fine metal (Au, Ag, Cu) wire was extruded with hydrostatic extrusion process in cold condition. A vertical type 900kN hydrostatic extruder has been developed. The extruder was facilitated with high pressure container which are available for hot and cold forming. The container endured 1400MPa internal pressure and extrusion ratio To was achieved in cold forming for Au fine wire which had $600{\mu}m$ diameter. In contrast to the conventional macroscopic-sized-billet fine-wire requires higher extrusion pressure and effect of friction is much more significant.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.313-317
• /
• 2003

Porthole die extrusion is the method which put the billet in the container and push it between die hole by ram. This method make it possible that product manufacture which have complex shape of area with excellent induction of area, in addition that this is economical. So this method is used as the basic manufacturing method of many industrial materials. The subject of this research is the forming technology development of heat sink which is being produced by extrusion process in my country. Flow condition of extrusion for heat sink, and metal flow of billet in the die are estimated by the means of rigid-plasticity finite element method.

• 소성∙가공
• /
• 제11권4호
• /
• pp.363-370
• /
• 2002

In this study, an optimal design technique was investigated for determining appropriate dimensions of components of the die set used in the extrusion process. For this, an axi-symmetric elastic finite element program for the analysis of deformation of the shrink fitted die set was developed with the Lagrange multiplier method to implement the constraint condition of shrink fit of stress ring. By coupling the rigid-viscoplastic analysis of extrusion process by CAMPform and elastic analysis of the die set, the optimization study was made by employing optimization program DOT. Considering the various assembly conditions, optimal design was determined for a single stress ring case. It is construed that the proposed design method can be beneficial for improving the tool life of cold extrusion die set at practice.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1992년도 춘계학술대회 논문집 92
• /
• pp.27-46
• /
• 1992

In this study a new simplified three-dimensional numerical method and the associated computer program have been developed to simulate the non-axisymmetric extrusion processes. The two-dimensional rigid-plastic finite element method under the generalized plane-strain condition, is combined with the slab method. To define the die geometry for non-axisymmetric extrusion, area mapping technique was used. Streamlined die surface was used to miniminze the total extrusion pressure. Extrusion of square, hexagonal and "T" section from round billet have been simulated and experimented with a model material. The computed results were in good agreement with the experiments in cross-sectional grid distortion. Computational results will be valuable for designing tool geometries and corresponding processes.