• 한국주조공학회지
• /
• 제18권6호
• /
• pp.541-549
• /
• 1998

Microstructural characteristics of hypereutectic Al-Si alloys during reheating at semi-solid temperature have been investigated. The size and morphology of primary Si particles in wedge-type mold-cast ingot has been compared with hot-rolled sheet and Si particulate reinforced Al composite. Effects of P and Sr addition on the morphological changes of primary Si particles have been also investigated. Observation of the solidification microstructures of the wedge-type mold-cast ingot at different cooling rates showed that alloying elements such as P and Sr affect the morphology of Si particles, especially in the area solidified at a slow cooling rate. Negligible change in the size of primary crystals was observed after reheating experiment, but ${\alpha}-halo$ formed around the Si particles and fine particles of Si precipitated in the surrounding area of the Si particles. In addition, there seemed to be no coarsening with increasing of holding time and the region of ${\alpha}-halo$ being decreased. Nucleation and recrystallization was accelerated with addition of alloying elements during hot rolling resulting in a decrease of primary Si particle size. In the case of extruded specimens, morphological change of primary Si particles was not observed after reheating. No ${\alpha}-halo$ formation was observed in Si reinforced Al composite because of the oxide film formed on the Si particles which acted as a diffusion barrier between substrate and the primary Si particles.

• KIEAE Journal
• /
• 제13권2호
• /
• pp.53-60
• /
• 2013

This study examined the building envelope structure used in small housings near urban area which have not good energy source in relation to the application of passive design for energy saving of small-sized architectural design firms in local cities and aimed to provide the basic materials of future design direction of designers and housing owners by analyzing economy of a project in order to know the amount of energy saving and additional expenses depending on the building envelope pattern. As a result of comparing and examining the energy saving cost from the period of use compared to investment by the thickness of insulating materials based on building envelope pattern for energy saving, it was found that the thicker the insulating materials are, the more energy saving amount is. While the current bead-type insulating materials have short payback period due to low initial investment, extruded insulating materials show the difference of five years compared to bead-type insulation because of its high initial investment.

• 청정기술
• /
• 제19권2호
• /
• pp.121-127
• /
• 2013

본 연구의 목적은 알럼 슬러지를 사용하여 입상흡착제를 제조하기 위한 압출 공정을 최적화하는 것이다. 함수율과 바인더인 메틸 셀룰로스의 함량이 압출 가능성과 입상흡착제의 물리적 특성에 미치는 영향을 연구하였다. 입상흡착제의 물리적 특성은 질소 흡착실험과 압축 강도 측정을 통해서 분석하였다. 증류수와 알럼 슬러지 가공분말의 비가 63/100인 경우가 입상흡착제의 외형이 원통형으로 잘 성형되었고, 압축강도도 가장 높게 나타났다. 메틸 셀룰로스의 함량을 증가시키면 압축강도가 개선되었으나 비표면적이 감소하였다. 성형된 입상흡착제의 소성과정을 거치면 입상흡착제의 표면적이 크게 증가하여 황화수소의 파과 시간이 획기적으로 증가하였으며, 황화수소 파과 용량은 1,700 mg/g 이상을 얻을 수 있었다.

• 한국식품영양과학회지
• /
• 제38권12호
• /
• pp.1760-1766
• /
• 2009

찹쌀가루, 쌀가루, 탈지콩가루 및 소금을 첨가하여 수분함량 16-18%, screw 속도 300 및 400 rpm, feed rate 43.4kg/hr 조건에서 extruder로 제조한 유과바탕의 특성은 다음과 같았다. 길이, 직경 및 비용적은 extruder에서 공급되는 수분함량이 낮을수록 크게 나타났다. 유과바탕의 색도 중 L값은 수분함량이 많을수록 높은 반면, a값 및 b값은 낮게 나타났다. 유과바탕의 수분흡착지수는 수분 함량이 많을수록 유의적으로 증가되었다. 유과바탕의 x-ray 회절도는 수분함량 16% 및 17%에서는 B도형을 나타냈으며, 수분함량 18%에서는 A도형을 나타냈다. 상대적 결정화도와 breaking strength는 수분함량 16%에서 가장 낮게 나타났으며, 17%, 18%에서는 유의적인 차이가 없었다. TPA에서 hardness는 수분함량 16% 및 17%, screw 속도 400 rpm에서 가장 낮게 나타났다. 유과바탕의 단면을 40배로 확대하여 관찰한 유과바탕은 수분함량이 증가할수록 기공의 크기가 컸고 세포벽은 두꺼웠다. 유과바탕의 관능검사 결과 수분함량에 따른 색과 향미에 대한 기호도는 유의적인 차이는 없었으나, 맛, 외관, 입안에서의 느낌 및 전체적인 선호도는 수분함량이 낮을수록 기호도는 높게 나타났다.

• 공업화학
• /
• 제19권2호
• /
• pp.161-167
• /
• 2008

다층카본나노튜브(MWCNT)가 강화된 폴리에틸렌에틸아크릴레이트(EEA) 나노복합체를 용융혼합법과 용액혼합법으로 제조하였다. 카본나노튜브의 형태 및 함량변화에 따른 기계적, 열적, 전기적 특성을 조사하였다. MWCNT의 함량이 증가함에 따라 인장강도, 모듈러스는 증가하였고, 파단신장률은 감소하였다. 할로우 형태의 MWCNT가 일반적인 MWCNT에 비해 우수한 인장강도 및 파단신장률을 나타내었다. MWCNT 함량이 증가함에 따라 약 $40^{\circ}C$의 열분해온도의 향상을 보였다. 전기적 특성은 용융혼합법의 경우가 가장 높은 전기저항 특성을 나타내었고, 용액혼합법의 경우 일반형 MWCNT가 할로우 MWCNT보다 낮은 체적저항을 보였다. MWCNT의 함량이 증가할수록 파단면 위로 돌출되는 CNT 수가 증가하였고, 인장변형을 가하면 표면 위로 돌출되는 CNT 수와 길이가 크게 증가하였다. 용융혼합된 시편이 용액혼합에 비해 돌출된 CNT의 수와 길이가 현격히 낮았다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.1202-1203
• /
• 2015

This paper describes the development of HVDC ${\pm}500kV$ polypropylene laminated paper (PPLP) mass-impregnated (MI) type cable system for HVDC transmission lines. As you know, mass-impregnated type cable generally has only insulating layer with the Kraft paper impregnated with a high-viscosity insulating compound. But polypropylene laminated paper is made of a layer of extruded polypropylene (PP) film sandwiched between two layers of Kraft paper. Thanks to PP film and its combination with Kraft paper, PPLP has higher AC, Impulse (Imp.) and DC breakdown (BD) strengths as well as lower dielectric loss than conventional Kraft paper insulation. In addition, Kraft MI cable has a limitation for the maximum conductor temperature as $55^{\circ}C$ But this PPLP MI cable has higher maximum conductor temperature than that of Kraft MI cable due to advantage of oil drainage characteristics. It is the most economic type of cable for HVDC transmission. Also HVDC ${\pm}500kV$ PPLP MI cable system was developed including land joints and outdoor-terminations. In order to prove the mechanical and electrical performances, the type test was carried out according to CIGRE recommendations. A full scale cable system has been tested successfully. And additional load cycle and polarity reversal tests on the cable system showed a higher performance compared with a similar mass impregnated paper cable.

• 한국식품과학회지
• /
• 제48권2호
• /
• pp.147-152
• /
• 2016

전통 감주 제조 중 쌀 콜렛 분말 사용량과 당화시간에 따른 이화학적 특성과 관능검사를 조사하였다. pH는 동일한 당화시간과 동일 시료의 경우 불규칙하게 미미한 변화가 있었으나, 당화에 특별한 지장은 없었다. 점도는 콜렛 분말 비율의 증가 및 당화시간이 경과할수록 미세하게 높아졌으며, 쌀 콜렛 분말:엿기름 추출물에서 쌀 콜렛 분말의 비율이 25% 이상일 때는 그 값이 낮아졌다(p<0.05). 색도는 콜렛 분말이 증가할수록 L값, a값 및 b값은 동일시간에서 높아졌고, ${\Delta}E$값은 낮아졌다. 당화시간이 경과할수록 L값은 5:95는 불규칙하게 약간 높아졌으나, 그 외는 시료와 무관하게 시간이 경과할수록 낮아졌다. a값, b값 및 ${\Delta}E$값은 당화시간이 경과할수록 불규칙하지만 높아지는 경향이었다(p<0.05). 당도는 콜렛 분말의 양이 증가하거나 당화시간이 경과할수록 모든 시료에서 당도가 높아졌다. 5:95-15:85는 14.8-27.6으로 급격히 증가하였고, 15:85 이상에는 완만하게 증가되었다. 환원당은 콜렛분말의 증가 및 당화시간이 경과할수록 모든 시료에서 17.92-20.71 mg/mL로 매우 높게 나타났으며(p<0.05), 지금까지 보고된 어떠한 식혜보다 점도, 당도 및 환원당 함량은 높은 값을 보였다. 유리아미노산은 시료 중 콜렛 분말의 비율이 증가할수록 함량이 증가되는 경향이었으며, 생균수는 실활 시키지 않은 모든 시료에서 균이 검출되었으므로(p<0.05) 반드시 멸균이 필요하였다. 관능검사에서는 시료 25:75, 당화는 5시간일 때 패널의 기호도를 충족하는 것으로 평가되었다(p<0.05).

• 한국정밀공학회지
• /
• 제19권2호
• /
• pp.95-105
• /
• 2002

In order to reduce the lead-time and cost, the technology of rapid prototyping (RP) has been widely used. However, RP technologies have disadvantageous characteristics according to their working principle: low building speed, high cost for introduction and maintenance of RP apparatus, stair-stepped surface and additional post processing. A new rapid prototyping process, as a transfer type of Variable Lamination Manufacturing by using expandable polystyrene room (VLM-ST), has been developed to reduce building lime. apparatus cost including the introduction and the maintenance and additional post-processing. The objective of this study is to propose a VLM-ST process and to develop an apparatus for implementation of the process. Design criteria of the apparatus are defined and the techniques arc proposed to satisfy the design criterion. In order to examine the efficiency and applicability of the developed process, various three-dimensional shapes, such as a world-cup logo. a knob shape, an extruded cross, a twisted shape, a character, Son-o-kong. a helical gear shaped and a scissor shape are fabricated on the apparatus in which unit shape layer (USL) was generated to build up each layer.

• 한국의류산업학회지
• /
• 제13권4호
• /
• pp.600-613
• /
• 2011

The purpose of this study is to provide Torso pattern for Korean middle-aged women using 3D human body scan data. 155 women in their 40's or 50's were measured by Martin's anthropometry. Merging the data of 914 middle aged women provided by Korean agency for technology and standards, total of 1,069 subjects' data were analyzed. For data analysis, ANOVA, factor analysis and cluster analysis were done using SPSS PC+. And representative subject of each cluster was selected and they participated in 3D scanning and Torso pattern suggested for middle-aged women Torso pattern which investing the amount of ease according to each group for diffuse front interscye 30%, armscye circumference 30%, back interscye 40% using 3D human body scan data. The results of this study are as follows. Firstly, as a result of the factor analysis, the first factor was 'obesity index of body', The second factor was 'verticality size of body', The third factor was 'verticality length of upper bodice', The fourth factor was 'drop value to represent silhouette', and the fifth factor was 'physique of upper bodice'. And, middle-aged women type were classified 3 types according to the cluster analysis. Type 1(Y-type) was the long upper Torso with wide shoulder. Type 2(H-type) was flat-body type with comparatively thin upper bodice and thin lower bodice. And type 3(A-type) was the obese type with comparatively thin upper bodice and fat lower bodice. Secondly, using CAD program, point filtering was performed and approximated surface model was made. It used that generated surface smoothing corrected for abnormally extruded points and scattered points based on the curvature information. And 3D surfaces were flatted onto the plane by the internal tools of CAD program. Difference ratios of outline length and area between 3D curves and 2D plane were 0.42% and 0.54%, respectively. Third, wearing test by the sensory evaluation showed that distinct difference almost every category. The movement functionality test shows that, in all the tests which reveal significant differences, especially, 'comparison pattern A' experienced inconvenience to neck width and neck depth.

• 한국산업보건학회지
• /
• 제3권1호
• /
• pp.91-98
• /
• 1993

This study was carried out to investigate characteristic of vinyl chloride emissioned from poly vinyl chloride extrusion process and to evaluate the efficiency of local exhaust ventilation system. Before local ventilation facility was constructed in poly vinyl chloride extrusion process, the average worker exposure to vinyl chloride was 3.15 ppm, which exceeded Threshold Limit Value of American Conference of Gorvernmental Industrial Hygienists (ACGIH-TLV), 1 ppm. lt is possible that vinyl chloride residues in the poly vinyl chloride resin was released or degased due to extrusion heat. The larger the width of vinyl tube become, the higher worker exposure to vinyl chloride was. It is estimated that vinyl chloride from vinyl chloride resin increased as amount of poly vinyl chloride resin extruded in the extrusion process increased. Canopy hood was an appropriate type for poly vinyl chloride resin extrusion process. This local exhaust ventilation has fan static pressure of 7.65 inch wg($190mmH_2O$, total volumetric flowlate of 4,796 CFM ($135.8m^3$/min) and fan power requirement of 12 hp (8.952 Kw). After this local exhaust ventilation was constructed there, the average concentration of worker exposure to vinyl chloride was reduced to be 0.46 ppm, which was below the Threshold Limit Value, 1 ppm. Also, the removal efficiency rate of vinyl chloride attained by local exhaust ventilation was 85.3%. It was a statistically significant (p<0.01).