• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2014년도 제49회 KOSCO SYMPOSIUM 초록집
• /
• pp.277-280
• /
• 2014

Global energy demand has continued to rise due to population increase and economic development. National governments and international bodies try to seek the ways to reduce the demand growth. Energy Technology Perspectives (ETP) have provided the current status of energy system, technology developments and external events that have changed ETP scenario since 2006. The status and prospects for key energy technologies of transport sector are presented. Technology portfolio for the transport sector should be needed to meet very low CO2 targets. The portfolio includes improved fuel economy of current internal combustion engine vehicles, advanced technologies such as electric and fuel-cell vehicles, advanced biofuels and demand-side management.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.571-575
• /
• 2006

To improve economic of solar power generation, stirling engine is required continuous operation and the receiver has to be provided with an additional combustion system. The hybrid receiver with a specially adapted combustion system is possible to 24 hr/day operation by solar and gas-fired. The inner cavity and external wall serve as absorber surfaces using collected irradiation and heat transfer surfaces for the gas heat flow, respectively. The hybrid receiver was designed and fabricated for the dish/stirling system. The analytical method for pridicting natural convective heat loss from receiver is used. The Koenig and Marvin model is used to estimate convection heat loss and heat transfer coefficiency.

• Advances in materials Research
• /
• 제8권2호
• /
• pp.117-135
• /
• 2019

The lifetime of a gas turbine combustor is typically limited by the durability of its liner, the structure that encloses the high-temperature combustion products. The primary objective of the combustor thermal design process is to ensure that the liner temperatures do not exceed a maximum value set by material limits. Liner temperatures exceeding these limits hasten the onset of cracking which increase the frequency of unscheduled engine removals and cause the maintenance and repair costs of the engine to increase. Hot gas temperature prediction can be considered a preliminary step for combustor liner temperature prediction which can make a suitable view of combustion chamber conditions. In this study, the temperature distribution of ceramic panels for a V94.2 gas turbine combustor subjected to realistic operation conditions is presented using three-dimensional finite difference method. A simplified model of alumina ceramic is used to obtain the temperature distribution. The external thermal loads consist of convection and radiation heat transfers are considered that these loads are applied to flat segmented panel on hot side and forced convection cooling on the other side. First the temperatures of hot and cold sides of ceramic are calculated. Then, the thermal boundary conditions of all other ceramic sides are estimated by the field observations. Finally, the temperature distributions of ceramic panels for a V94.2 gas turbine combustor are computed by MATLAB software. The results show that the gas emissivity for diffusion mode is more than premix therefore the radiation heat flux and temperature will be more. The results of this work are validated by ANSYS and ABAQUS softwares. It is showed that there is a good agreement between all results.

• Tribology and Lubricants
• /
• 제23권6호
• /
• pp.306-311
• /
• 2007

This paper presents the friction characteristics of pb-fres pin bushing bearings for an automotive gasoline engine. The external load is 100 N to 600 N and the speed of the pin bushing bearing is 1000 rpm to 3000 rpm against the rubbing surfaces. And the contact modes of rubbing surfaces between a piston pin and a pb-free pin bushing specimen are a dry friction, an oil lubricated friction and a mixed friction that is starved by a lack of engine oil. Two influential factors of a contact rubbing modes and a material property are very important parameters on the tribological performance of a friction characteristic between a piston pin and a pb-free pin bushing. The experimental result shows that the pin bushing speed of 2000 rpm shows a typical oil film lubricated sliding contact mode in which means that as the applied load is increased, the friction loss is increasing. But other contact mode depending on the speed and the load may affect to the fiction coefficient without a regular and uniform trend. In summary, the oil lubricated rubbing surface definitely decreases a running-in period in short and increase oil film stiffness, and this may leads the reduction of a friction loss.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.903-908
• /
• 2001

Residual gas acts as a diluent which results in reducing the in-cylinder temperature as well as the flame speed, significantly affecting fuel economy, NOx emissions and combustion stability. Therefore it is important to determine the residual gas fraction as a function of the engine operating parameters accurately. However, the determination of the residual gas fraction is very sophisticated due to the unsteady state of induction and exhaust process. There has been little work toward the development of a generally applicable model for quantitative predictions of residual gas fraction. In this paper, a simple model for calculating the residual gas fraction in SI engines was formulated. The effects of engine operating parameters on the residual gas were also investigated. The amount of fresh air was evaluated through AFR and fuel consumption. After this, from the intake temperature and pressure, the amount of total cylinder-charging gas was estimated. The residual fraction was derived by comparing the total charging and fresh air. This results coincide with measured value very well.

• 한국자동차공학회논문집
• /
• 제18권3호
• /
• pp.37-42
• /
• 2010

Plastic region tightening is widely used in critical bolted joints in internal combustion engines in order to reduce the engine weight by maximizing the use of load-carrying capacity of bolt. Mechanical behavior of bolt tightened in plastic region under external axial tensile load is investigated for various friction conditions using three dimensional finite element analysis. The behavior of bolt tightened in elastic region as well as that in tensile test are investigated for comparison. Tightening process is simulated by rotating the bolt in order to examine the friction effect realistically. It is revealed that the bolt tightened in plastic region can carry more external load until the joint is opened, and yields at lower bolt load than the bolt tightened in elastic region. The friction coefficient has effect on the yield load, but not on the load-carrying capacity. Moreover, the scatter in the bolt preload due to friction begins with plastic deformation of bolt in the angle tightening control, whereas it begins with the onset of tightening in the torque tightening control. The observations are interpreted with the residual torsional stress in the bolt generated during the tightening.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권8호
• /
• pp.1152-1161
• /
• 2009

신조선 선박에서 시운전 중 주 추진 시스템의 동력을 측정하는 방법은 스트레인 게이지를 이용하여 축의 변형률로부터 얻어지는 직접적인 방법과 기계적인 또는 전기적인 픽업을 이용하여 계측한 실린더연소압력으로부터 환산된 면적에 의한 간접적인 방법으로 구분할 수 있다. 이러한 동력은 장주기로 선박의 여러 가지 해상 운동에 의해서 그리고 단주기로는 축계의 비틀림, 축계 배치 및 횡진동의 영향에 의해서 변동한다. 본 논문에서는 축동력측정과 평가를 위하여 통계적인 해석법을 소개하고 있고, 저속2행정디젤엔진과 감속기를 포함 중속 4행정 디젤엔진 모델에 의해서 이들이 확인되고 있다.

• 한국항해학회지
• /
• 제14권4호
• /
• pp.53-70
• /
• 1990

Much efforts have been made to improve the training education system for last decades. however, it still leaves much room form improving the system. The reason for this is that the have been many changes in given educational conditions, national and international, and that there existed the lack of training facilities on shore and the limits of capacity on the training ship. The existing program adopts a straight-through system of which the course has to be completed at same time, and also forces students to study the course, disregarding their aptitude for sea life. Consequently, the program resulted in frustrating the learning desire of some students and, as a consequence, in deteriorating the quality of the entire training education. This paper aims to develop an efficient training program including curriculla by the literature survey and the teaching and sea experiences on the training ship "HANBADA" and merchant ships, where the authors have been for many years. Compared with the existing one, the new training model suggested in this paper has some advantages as follows : First, the new model adopts multi-state system which consists of various short-term training courses according to each purpose. This system will be helpful for student to find their aptitude for sea life earlier and to understand classes of major subjection shore. Second, the model includes new curriculla which consist of core subjects (for example, navigation, marine operation, marine transportation, watch keeping and nautical English for deck cadets and internal and external combustion engine, auxiliary machinery, electric and electronics and engine maintenance for engine cadets), by incorporating existing 20 subjects in 5 subjects. These curriculla may contribute to embodying the characteristics of training education where the above mentioned subjects must be linked with each other. In order to implement this new training model efficiently and effectively, the following prerequisties must be prepared : $\circled1$ The contents of each subject included in the new model should be systematically developed. $\circled2$ The educational schedule should be adjusted according to the new model.new model.

• 한국항공우주학회지
• /
• 제41권10호
• /
• pp.796-804
• /
• 2013

연소 및 추진 기관 공학 교육 과정의 일부로써 간단한 형태의 열기관인 감자총 (Potato Gun)의 제작, 시험 및 해석을 수행하였다. 정적 연소실의 화학 평형 해석을 이용하여 연소실의 압력을 계산하고, 팽창과정의 열역학 해석을 통하여 열에너지의 운동에너지로 변환되는 내탄도 과정을 계산하였다. 공기역학적 지식을 도입한 구형 탄도 궤적 해석을 통하여 비행거리를 추정할 수 있었으며, 이를 통하여 감자총의 에너지 변환 효율 및 혼합기의 당량비를 추정하였다. 본 과제는 재활용 자재를 이용하여 학부 수준에서 열-유체역학공학 지식을 활용하여 실습하고 학생들의 관심을 유발할 수 있는 적당한 예로 여겨진다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 춘계학술대회 논문집
• /
• pp.219-222
• /
• 2009

파이로스타터는 터보펌프 터빈의 초기 구동을 위해 터빈에 고압의 가스를 공급함으로써 액체추진기 관의 터보펌프 시동기 역할을 수행한다. 파이로스타터는 일종의 가스발생기로써, 내부에 충전된 저온고체추진제의 연소가스를 통해 시동에 필요한 에너지를 터빈에 공급하게 된다. 파이로스타터 내부에 충전되는 고체추진제의 외부와의 환경적인 격리뿐만 아니라, 연소 초기 연소실 내부의 충분한 압력 증가를 통해 저온 고체추진제의 점화특성을 향상시킬 수 있는 파이로스타터용 럽쳐디스크 개발을 위해 럽쳐디스크의 두께, 스코어의 깊이 및 형태, 가압 속도에 따른 파열압력과 파열반경 경향에 대한 시험을 수행하였으며, 설계파열압력 및 요구 파열반경 등 실제 운영 조건을 만족하는 파이로스타터용 럽쳐 디스크의 성능을 시험결과를 통해 확인하였다.