• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.136-145
• /
• 2013

It is very important to determine specifications of components included in the drive-train of vehicles at the initial design stage. In this study, component sizing process and performance analysis for Extended-Range Electric Vehicles (E-REV) are discussed based on the foundation of determined system configuration and performance target. This process shows sizing results of an electric driving motor, a final drive gear ratio and a battery capacity for target performance including All Electric Range (AER) limit. For E-REV driving mode, the constant output power of a Gen-set (Engine+Generator) is analyzed in order to sustain State of Charge (SOC) of the battery system.

• 한국자동차공학회논문집
• /
• 제24권6호
• /
• pp.649-659
• /
• 2016

This paper describes control algorithm and control structure of vehicle control unit for range-extended electric vehicle equipped with engine-generator system, and specially presents methods which determine optimal operating points and decreases a vibration or a shock for operating the engine-generating system. The vehicle control algorithm is consisted of several parts which are sequence control, calculation of wheel demand torque, determination of operating points, and management of operating points and so vehicle controller has be made possible to efficiently manage calibration parameters. The control algorithm is evaluated by driving test modes, launching performance and operating engine-generator system and so on. In conclusion, this paper present methods for extending a mileage, improving a launching performance and reducing vibration or shock when the engine-generating system is starting or is stopping.

• 한국자동차공학회논문집
• /
• 제22권4호
• /
• pp.160-164
• /
• 2014

Recently, there has been an active study about friction force of moving parts for automotive. This study is development and evaluation of oil pockets for journal bearing and tappet valve for range extended electric vehicle. Specially, oil pockets are effect on friction force depend on pitch, size, depth. In this study, fine oil pocket was formed using by etched texturing on the journal bearing and tappet valve. And oil pocket analyzed by SEM and friction force test was carried out by tensile tester. Finally, in this study, it was suggested by round and plane part which journal besring and tappet valve.

• 전기학회논문지P
• /
• 제65권4호
• /
• pp.273-279
• /
• 2016

In this paper, a high-performance control of the induction motor for electric car was implemented to escape dependence of the rare earth magnet. Proposed high-efficiency control algorithm is a Direct Rotor Field-Oriented Control method that is insensitive to the fluctuation of motor parameters. In the DRFOC method, we need to compensate fluctuation of stator transient inductance and magnetizing inductance caused by the magnetic saturation of induction motor in high-speed area. This paper proposes Back-EMF Observer based on stator current estimator of Luenberger style. Motor control system applied the Voltage Feedback Flux Weakening Control method for high-speed operation. The proposed algorithm was verified through tests by the power train of Extended Range Electric Vehicle consists of induction motor and differential gear.

• 전기학회논문지
• /
• 제65권12호
• /
• pp.2197-2210
• /
• 2016

Recently, the trend of zero emissions has increased in automotive engineering because of environmental problems and regulations. Therefore, the development of battery electric vehicles (EVs), hybrid/plug-in hybrid electric vehicles (HEVs/PHEVs), and fuel cell electric vehicles (FCEVs) has been mainstreamed. In particular, for light-duty electric vehicles, improvement in electric motor performance is directly linked to driving range and driving performance. In this paper, using an improved design for the interior permanent magnet synchronous motor (IPMSM), the EV driving range for the light-duty EV was extended. In the electromagnetic design process, a 2D finite element method (FEM) was used. Furthermore, to consider mechanical stress, ANSYS Workbench was adopted. To conduct a vehicle simulation, the vehicle was modeled to include an electric motor model, energy storage model, and regenerative braking. From these results, using the advanced vehicle simulator (ADVISOR) based on MATLAB Simulink, a vehicle simulation was performed, and the effects of the improved design were described.

• 한국산학기술학회논문지
• /
• 제19권7호
• /
• pp.1-8
• /
• 2018

본 논문은 주행거리 연장형 전기자동차에서 발전량을 결정하는 차량 제어기와 이를 수행하는 엔진 제어기 간 토크 명령을 전달하기 위한 새로운 통신방법을 설명한 것이다. 일반적으로 자동차는 CAN 통신방식을 사용하지만, 이 경우 기존 엔진 제어기의 하드웨어 및 소프프웨어를 수정해야만 한다. 이러한 이유로 중소 자동차 개조업체는 발전용 엔진이 탑재된 주행거리 연장형 전기자동차에 대한 개발 및 개조 작업 시 CAN통신방식의 적용이 쉽지 않다. 따라서 본 연구과정에서는 기존의 양산용 엔진 제어기를 주행거리 연장형 전기자동차에 적용하기 위한 핀-핀 통신방안를 제시하였다. 핀-핀 통신방안은 기존 양산용 엔진 제어기내에 탑재된 운전자요구토크 제어 맵을 엔진의 목표속도와 목표토크에 따른 가상 엑셀 열림량으로 변환하는 과정과 이를 기존 양산 엔진제어기가 인식 할 수 있도록 해당 엑셀페달 전압신호로 변환하는 과정으로 구성된다. 가상 엑셀 열림량은 오프라인 환경에서 역 변환 과정을 통하여 차량 최상위제어기에 제어 맵 형태로 탑재되고, 엔진 발전요구량과 엔진 최적 운전점 알고리즘을 통하여 결정된다. 이렇게 결정된 가상엑셀 열림량은 DA신호 변환기를 통하여 기존 엔진제어기가 인식할 수 있는 전압신호로 최종적으로 변환된다. 엔진토크 전달을 위한 이러한 알고리즘과 신호변환 회로는 차량제어기(VCU)에 탑재되어 엔진목표토크에 따른 가상엑셀페달 열림량 변환과정과 신호변환기를 이용한 가상 엑셀페달 전압신호에 대한 통신시험을 실시하여 이러한 통신방식의 실현 가능성을 입증하였다.

• 제어로봇시스템학회논문지
• /
• 제16권7호
• /
• pp.617-624
• /
• 2010

This article describes the system architecture of KUVE (KIST Unmanned Vehicle Electric) and unmanned autonomous navigation of it in KIST. KUVE, which is an electric light-duty vehicle, is equipped with two laser range finders, a vision camera, a differential GPS system, an inertial measurement unit, odometers, and control computers for autonomous navigation. KUVE estimates and tracks the boundary of road such as curb and line using a laser range finder and a vision camera. It follows predetermined trajectory if there is no detectable boundary of road using the DGPS, IMU, and odometers. KUVE has over 80% of success rate of autonomous navigation in KIST.

• 한국자동차공학회논문집
• /
• 제20권5호
• /
• pp.138-144
• /
• 2012

Recent environmental issues such as exhaust gas and greenhouse effect make the agricultural machinery market takes into account the hybrid and electric propulsion technology used in automotive engineering. Generally the agricultural machinery, particularly an agricultural tractor, needs large load capacity and long continuous operating time comparing with conventional vehicles. In case of a pure electric tractor, it is necessary for considering large capacity batteries and long charging time. Therefore we take an AER extended PHEV (All Electric Range extended Plug-in Hybrid Electric Vehicle) power transmission system in developing an electric tractor in this study. First we propose a PHEV powertrain structure in order to substitute the conventional diesel engine equipped tractor. And we performed the road tests using a conventional mechanical tractor with various load conditions, which were classified and statistically treated real agricultural works. The test results were analysed with respect to the power characteristics of the power source. Finally using the test result, we designed two-stepped reduction gear ratios in the proposed an electric tractor powertrain for carrying out typical agricultural works.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권11호
• /
• pp.535-540
• /
• 2003

Since axial flux motor has an advantage over more conventional radial flux type motor such as high power density, it can be used as a power train for hybrid electric vehicle and electric vehicle. Also operating range can be extended and efficiency can be improved by changing air gap. Optimal operating air gap is estimated based on the measured efficiency at different air gap. Motor model is developed based on estimated optimal air gap and efficiency. Motor/controller performance is analyzed through simulation. Possible application area of axial flux motor was explored through simulation.

• Journal of Electrical Engineering and Technology
• /
• 제9권6호
• /
• pp.2025-2035
• /
• 2014

The read range of UHF mobile readers can be extended by a booster for mobile RFID readers (BoMR). But in an environment where multiple BoMRs are installed, the read success rate may be decreased due to signal interference. This paper proposes three arbitration methods based on interference estimation with the purpose of enhancing the read success rate. A central arbitration server manages global information in centralized arbitration method (CAM) without broadcast/multicast communication facility. In fully distributed arbitration method (FDAM), all the arbitration messages are broadcasted from a BoMR to every BoMR, and each BoMR decides with broadcasted global information. Events in FDAM are serialized naturally with broadcasted messages. Cluster Distributed Arbitration Method (CDAM) forms clusters with multicasted BoMRs and a selected BoMR acts as an arbiter in the cluster. Such effects as lengthened read range, improved the read success rates of readers can be obtained by the proposed methods without any hardware modification. In order to evaluate the arbitration methods, the RFID system is modeled by using the DEVS formalism and simulated by using the DEVSim++.