• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.10
• /
• pp.1621-1626
• /
• 2001

The structural optimization have been carried out in the continuous design space or in the discrete design space. Methods fur discrete variables such as genetic algorithms , are extremely expensive in computational cost. In this research, an iterative optimization algorithm using orthogonal arrays is developed for design in discrete space. An orthogonal array is selected on a discrete des inn space and levels are selected from candidate values. Matrix experiments with the orthogonal array are conducted. New results of matrix experiments are obtained with penalty functions leer constraints. A new design is determined from analysis of means(ANOM). An orthogonal array is defined around the new values and matrix experiments are conducted. The final optimum design is found from iterative process. The suggested algorithm has been applied to various problems such as truss and frame type structures. The results are compared with those from a genetic algorithm and discussed.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.15-24
• /
• 1998

In this research. we have proposed a new technique to determine .the combination of design parameters for the process design of a hot forged product using artificial neural network(ANN) and statistical design of experiments(DOE). The investigated problem involves the adequate selection of the aspect ratio of billet, the ram velocity and the friction factor as design parameters. An optimal billet satisfying the forming limitation, die filling, load and energy as well as more uniform distribution of effective strain, is determined by applying the ability of artificial neural network and considering the analysis of mean and variation on the functional requirement. This methodology will be helpful in designing and controlling parameters on the shop floor which would yield the best design solution.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.6
• /
• pp.799-806
• /
• 2004

This paper presents a scheme for finding an optimal combination of design parameters affecting on the handling performance of a large truck using design of experiments. The average of the sum of peak-to-peak roll angles at the first and second part of the double lane is used as an objective function for design of experiments. Six design parameters are selected from all possible parameters affecting on the handling performance. The table of orthogonal arrays is made by 27 times simulations. A computational model of a large truck is developed by MSC/NASTRAN and MSC/ADAMS, and verified the reliability of it with the results of vehicle tests performed in a double lane change course. It is used for the simulations. Analyses of variance and factor effect of the table of orthogonal arrays are performed. This paper proposes an optimal combination of those six design parameters for improving the handling performance of the large truck.

• Journal of Korea Water Resources Association
• /
• v.36 no.5
• /
• pp.811-821
• /
• 2003

In this study is if the design of outlet conduit was appropriate or not by analyzing flow characteristic of outlet conduit with performing hydraulic model experiments. As the results of hydraulic model experiments, the capacity of outlet conduit of elementary design was under estimated, and the designed values of the capacity of outlet conduit of preliminary design based on the values of elementary design was nearly equal to the values of experiments, so the propriety of design was identified. In addition, as the results of examinations of negative pressure of outlet conduit, and propriety of longitudinal sections, the resulting values were within the maximum permissible limits, so it was proved that the design was appropriate. In the base of such processes, the propriety of scale and location of outlet conduit of preliminary design was examined.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.2
• /
• pp.193-200
• /
• 2012

Wheel loader is one of the construction machinery capable of variety of tasks and the demand on functional diversity and structural reliability is growing. As a study on the optimal shape design of front axle for wheel loader through the design of experiments, this paper assessed the design parameters affecting the maximum stress. As a result, a value of 126.77 MPa of minimum stress was obtained, and optimal factors showed the values of w = 100.0 mm, ${\theta}=40^{\circ}$ and R = 118 mm. It showed an accuracy of 98.7% compared with the structural analysis.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.8
• /
• pp.726-732
• /
• 2009

In many industries, the linear motor replaces the existing framework for linear transportation. Similar to other conventional motors, it is important to minimize the ripple of thrust and to maximize the thrust force of the linear motor. Because the two objectives are associated to each other, the multi-objective design process is necessary considering all objectives. This paper intends to optimize geometric parameters of the linear motor with two design objectives using design of experiments and sequential response surface method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.1
• /
• pp.24-32
• /
• 2016

The mortality rate of car-pedestrian accidents is quite high, compared to the frequency of accidents. Researches on pedestrian protection are being actively performed worldwide. The A-pillar and lower part of the wind shield cause the most serious damage to the pedestrians. Typical devises to protect the pedestrians are the hood lift system and pedestrian airbag. The design of such devices for an sport utility vehicle is performed based on a design process using design of experiments (DOE). The design results are obtained by an orthogonal array (OA), analysis of mean (ANOM) and analysis of variance (ANOVA). A metamodel is also used in the design process.

• Communications for Statistical Applications and Methods
• /
• v.7 no.3
• /
• pp.759-766
• /
• 2000

In order to design fractional factorial experiments which include some debarred combinations, we should select defining contrasts so that those combinations are to be excluded. Choi(1999) presented a method of selectign defining contrasts to construct orthogonal 3-level fractional factorial experiments which exclude some debarred combinations. In this paper, we extend Choi's method to general p-level fractional factorial experiments to select defining contrasts which cold exclude some debarred combinations.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.4
• /
• pp.1-8
• /
• 2004

Various controllable parameters of an experiment have influence on grinding process. In order to get good products with a high quality, these parameters should be considered whether each parameter has relations to the quality. This paper describes the use of the design of experiments to minimize geometric error in surface grinding. Controllable parameters for the design of experiments were selected as spindle speed, table speed, depth of cut and grain size. From the experimental results, a degree of influence between these parameters and the geometric error was evaluated. An optimal set of grinding conditions was obtained by means of analysis of variance(ANOVA).

• IE interfaces
• /
• v.18 no.4
• /
• pp.402-411
• /
• 2005

Secondary batteries with high performance are essential in widespread use of modern portable devices such as cellular phones and laptop computers. High energy density, long cycle life, and safety are some of important requirements for secondary battery. To achieve such characteristics, a mixing proportion of electrolyte solution ingredients in the battery should be carefully chosen. In this paper, using statistical design of mixture experiments (DOME), we attempt to find an optimum condition of designing the secondary battery. DOME has a distinct feature in that the experimental region is represented by simplex, rather than hypercube, because the sum of blend proportions should be unity. Several designs based upon this point have been proposed for mixture experiments. Among them, an extreme vertices design is employed in this paper because there are a couple of blend constraints to be considered. In order to investigate how the mixing proportion interacts with other manufacturing factors, a fractional factorial design is also included across the extreme vertices design. As a result, we find that the blend proportion of solution ingredients has a significant effect on battery performances. By simultaneously optimizing two battery capacities, this paper proposes an optimum blend proportion according to process factor settings.