• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• The Korean Journal of Physiology
• /
• 제1권1호
• /
• pp.103-120
• /
• 1967

As pointed out by many previous investigators, the cardio-pulmonary system of well trained athletes is so adapted that they can perform a given physical exercise more efficiently as compared to non-trained persons. However, the time course of the development of these cardio-pulmonary adaptations has not been extensively studied in the past. Although the development of these training effects is undoubtedly related to the magnitude of an exercise load which is repeatedly given, it would be practical if one could maintain a good physical fitness with a minimal daily exercise. Hence, the present investigation was undertaken to study the time course of the development of cardio-pulmonary adaptations while a group of non-athletes was subjected to a daily 6 to 10 minutes running exercise for a period of 4 weeks. Six healthy male medical students (22 to 24 years old) were randomly selected as experimental subjects, and were equally divided into two groups (A and B). Both groups were subjected to the same daily running exercise (approximately 1,000 kg-m). 6 days a week for 4 weeks, but the rate of exercise was such that the group A ran on treadmill with 8.6% grade for 10 min daily at a speed of 127 m/min while the group B ran for 6 min at a speed of 200 m/min. In order to assess the effects of these physical trainings on the cardio-pulmonary system, the minute volume, the $O_2$ consumption, the $CO_2$ output and the heart rate were determined weekly while the subject was engaged in a given running exercise on treadmill (8.6% grade and 127 m/min) for a period of 5 min. In addition, the arterial blood pressure, the cardiac output, the acid-base state of arterial blood and the gas composition of arterial blood were also determined every other week in 4 subjects (2 from each group) while they were engaged in exercise on a bicycle ergometer at a rate of approximately 900 kg m/min until exhaustion. The maximal work capacity was also determined by asking the subject to engage in exercise on treadmill and ergometer until exhaustion. For the measurement of minute volume, the expired gas was collected in a Douglas bag. The $O_2$ consumption and the $CO_2$ output were subsequently computed by analysing the expired gas with a Scholander micro gas analyzer. The heart rate was calculated from the R-R interval of ECG tracings recorded by an Offner RS Dynograph. A 19 gauge Cournand needle was inserted into a brachial artery, through which arterial blood samples were taken. A Statham $P_{23}AA$ pressure transducer and a PR-7 Research Recorder were used for recording instantaneous arterial pressure. The cardiac output was measured by indicator (Cardiogreen) dilution method. The results may be summarized as follows: (1) The maximal running time on treadmill increased linearly during the 4 week training period at the end of which it increased by 2.8 to 4.6 times. In general, an increase in the maximal running time was greater when the speed was fixed at a level at which the subject was trained. The mammal exercise time on bicycle ergometer also increased linearly during the training period. (2) In carrying out a given running exercise on treadmill (8.6%grade, 127 m/min), the following changes in cardio·pulmonary functions were observed during the training period: (a) The minute volume as well as the $O_2$ consumption during steady state exercise tended to decrease progressively and showed significant reductions after 3 weeks of training. (b) The $CO_2$ production during steady state exercise showed a significant reduction within 1 week of training. (c) The heart rate during steady state exercise tended to decrease progressively and showed a significant reduction after 2 weeks of training. The reduction of heart rate following a given exercise tended to become faster by training and showed a significant change after 3 weeks. Although the resting heart rate also tended to decrease by training, no significant change was observed. (3) In rallying out a given exercise (900 kg-m/min) on a bicycle ergometer, the following change in cardio-vascular functions were observed during the training period: (3) The systolic blood pressure during steady state exercise was not affected while the diastolic blood Pressure was significantly lowered after 4 weeks of training. The resting diastolic pressure was also significantly lowered by the end of 4 weeks. (b) The cardiac output and the stroke volume during steady state exercise increased maximally within 2 weeks of training. However, the resting cardiac output was not altered while the resting stroke volume tended to increase somewhat by training. (c) The total peripheral resistance during steady state exercise was greatly lowered within 2 weeks of training. The mean circulation time during exorcise was also considerably shortened while the left heart work output during exercise increased significantly within 2 weeks. However, these functions_at rest were not altered by training. (d) Although both pH, $P_{co2}\;and\;(HCO_3-)$ of arterial plasma decreased during exercise, the magnitude of reductions became less by training. On the other hand, the $O_2$ content of arterial blood decreased during exercise before training while it tended to increase slightly after training. There was no significant alteration in these values at rest. These results indicate that cardio-pulmonary adaptations to physical training can be acquired by subjecting non-athletes to brief daily exercise routine for certain period of time. Although the time of appearance of various adaptive phenomena is not identical, it may be stated that one has to engage in daily exercise routine for at least 2 weeks for the development of significant adaptive changes.

• Clinical and Experimental Pediatrics
• /
• 제49권12호
• /
• pp.1329-1339
• /
• 2006

목 적 : 조혈모세포이식은 혈액암뿐만 아니라, 유전 질환, 면역질환에서 완치의 방법으로 널리 사용되고 있다. 그러나 생착 실패나 재발로 인해 조혈모세포이식이 실패하는 경우가 종종 있고, 이때는 장기 생존이 거의 불가능한 것으로 알려져 있으며, 치료방법도 정립되지 않았다. 이에 본 저자들은 1차 이식이 실패한 경우 치료법으로써 2차 이식의 의의에 대해 알아보고자 하였다. 방 법 : 1991년 5월부터 2004년 12월까지 전남대학교병원 소아과에서 조혈모세포이식을 시행한 115례 중에서 생착 실패나 재발로 2차 이식을 시행한 비혈액암 8례(재생불량성빈혈 7례, 부신백질이영양증 1례)와 혈액암 7례(급성골수성백혈병 3례, 급성림프구성백혈병 2례, 만성골수성백혈병 1례, 골수이형성증후군 1례), 총 15례의 의무기록지를 바탕으로 치료 방법, 합병증, 치료성과 등에 대해 분석 하였다. 결 과 : 비혈액암의 경우 2례는 일차성 생착 실패, 5례는 후기 이식편 거부, 1례는 Fanconi 빈혈로 1차 이식 후 급성골수성백혈병으로 전환되어 2차 이식을 시행하였다. 1차 이식 후 이식편기능 부전까지 기간은 중앙값 130.5일(범위, 59-279일)이었고, 1차와 2차 이식 사이의 간격은 중앙값 348일(범위, 86-1,875일)이었다. 전처치는 7례에서 cyclophosphamide를 기본으로 하였고, fludarabine을 3례에서, 방사선 조사를 2례에서 사용하였다. 이식원은 6례에서 조직형 일치 형제간 말초조혈모세포를, 1례에서 조직형 일치 형제간 골수를, 1례에서 제대혈을 사용하였고, 제대혈을 사용한 1례를 제외한 7례는 2차 이식의 공여자가 1차 이식 시와 동일하였다. 급성 이식대숙주병은 1례에서 Grade IV로 발생하였다. 총 8례 중 2례가 사망하였고, 1례는 생착 실패하였으나 생존하여, 5년 Kaplan-Meier(K-M)전체생존율은 75.0%, 무병생존율은 62.5%이었다. 혈액암의 경우 모두 재발로 인해 2차 이식을 시행하였다. 1차 이식 후 재발까지 기간은 중앙값 174일(범위, 90-1,474일)이었고, 1차 이식과 2차 이식 사이의 간격은 중앙값 319일(범위, 178-1,715일)이었다. 전처치는 5례에서 fludarabine, busulfan, antithymocyte globulin 병합요법을, 1례는 busulfan, ara-C, idarubicine 병합요법을, 나머지 1례는 melphalan, busulfan 병합요법을 사용하였다. 이식원은 5례는 1차 이식과 동일한 공여자의 말초조혈모세포였고, 나머지 2례는 제대혈을 사용하였다. grade II 이상의 급성 이식대숙주병은 2례에서 발생하였다. 사망한 5례 중 4례는 재발로, 나머지 1례는 이식관련 합병증으로 사망하였다. 2년 K-M 전체생존율과 무병생존율은 각각 28.6%이었다. 결 론 : 조혈모세포이식을 시행하고 이식편 거부나 재발이 된 경우 2차 이식은 일부 환자에서 장기 생존을 가능하게 하는 방법이 될 수 있다. 비혈액암 질환, 특히 재생불량성빈혈에서 생착 실패를 보이는 경우 2차 이식을 시행하는 것을 추천할 수 있지만, 적절한 전처치와 이식원에 관한 연구가 더 필요하겠고, 혈액암 질환에서 재발한 경우에는 소수에서만 장기 생존이 가능하므로 더욱 효과적인 항백혈병 치료가 필요할 것으로 사료되었다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제6권1호
• /
• pp.131-181
• /
• 1983

After the investigation on, and the analysis of, the educational system for medical technicians and the present educational situation for medical technologies in this country, the following conclusions were drawn. 1. As of March 1983 the current academic system for education in medical technologies included the regular 4-year college courses and those of the 2-year professional junior college courses. But except in the cases on clinical pathology and physical therapy, there were no college-level departments. Particularly, no educational institutions, at whatever level, had a department for working therapies. 2. The total number of credits needed for graduation from a department of medical technologies was 150 points at a regular 4-year college and 85 to 96 points at a 2-year professional college. The obligatory minimum number of credits for a student at a professional college was set at 80 points and above. 3. As for the number of the educational institutions for medical technologies in this country, there were one regular college and 14 professional colleges, a total of 15 institutions. As many as 14 colleges had departments of clinical pathology, 12 had departments of Radiotechnology, 11 had departments of physical therapy, 12 had departments of dental technology, and eight had departments of dental hygiene. 4. The total capacity of the professional colleges in admitting new enrollment each year were 1,920 for clinical pathology, 1,552 for radiology, 1,012 for physical therapy, 1,334 for dental technologies, 828 for dental hygiene, an aggregate of 6,646 for all of the professional college departments. 5. The total number of graduates from the 12 professional colleges by department during the period of 1965-83 were 7,595 for clindical pathology, 4,768 for radiology, 2,821 for physical therapy, 3,000 for dental technologies, and 1,787 for dental hygiene, totalling 19,971 for all departments in the professional colleges. 6. In the state examination for licensed medical technicians, 12,446 have passed from among the total of 26,609 participants, representing a 45% passing ratio. By departments the ratios showed 44% for clinical pathology, 39.7% for radiology, 51.2% for physical therapy, 42.5% for dental technology, 72.5% for dental hygiene and 73.1% for working therapy. 7. As for the degree of satisfaction shown by the people in this field, 52.2 percent of the teaching staffs who responed to the questionaires said they were satisfied with their present profession, while the great majority of medical technicians(66%) replied that they were indifferent to the problem. 8. The degree of satisfaction shown by the students on their enrollment in this particular academic field was generally in the framework of indifference(43.7%), but mere students(36.5%) were satisfied with their choice than those were not satisfied(14.4%) 9. As for the student's opinions on the lectures and practicing hours, a good many students replied that, among such courses as general science and humanities courses the basic medical course, the major course and practicing hours, the hours provided for the general courses(47.1%) and practicing(47.6%) were insufficient. 10. When asked about the contents of their major courses, comparatively few students (23.6%) replied that the courses were too difficult, while a convincing majority(58.5%) said they were neither difficult nor easy. As for the appropriateness of the number of the present teaching staffs, a great majority(71.0%) of the students replied that the level of the teaching personnel in each particular field was insufficient. 11. Among the students who responded to the poll, good part of them(49.5%) wanted mandatory clinical practicing hours, and the the majority of them(64.6%) held the view that the experimental and practicing facilities of their schools were insufficient. 12. On the necessity of the attached hospitals, 71.1% of the teaching staffs and 58.0% of the medical technicians had the opinion that this kind of facility was indispensable. 13. As for the qualifications for applicants to the state examination in the licensing system for medical technicians, 52.2% of the teacher's and 36% of the medical technicians replied that the present system granting the qualifications according to the apprenticeship period should be abolished. 14. On the necessity of improving the present system for education in medical technologies, an overwhelming majority(94.4% of the :caching staffs, 92.0% of the medical technicians and 91.9% of students) of these polled replied that the present system should be changed for the better. 15. On the method of changes for the present educational system, a great majority(89.4% of the teaching staffs, 80.4% of the medical technicians and 90.1% of the students) said that the system must be changed so that it fits into the reality of the present day. 16. As for the present 2-year program for the professional colleges, 61.6% of the teachers, 72.0% of the medical technicians and 38.8% of the students expressed the hope that the academic period would be extended to four regular years, hemming a full-fledged collegelevels program. 17. On the life-long eductional system for medical technicians, there was a considerable number of people who expressed the hope that an open university system(38.9% of the teaching staffs, 36.0% of the medical technicians) and a graduate school system would be set up. 18. As for the future prospects for medical technicians as professionals, the optimists ana pessimists were almost equally divided, and 41.1% of the teaching staffs 36.0% of. the technicians and 50.5% of the students expressed an intermediate position on this issue.

• Investigative Magnetic Resonance Imaging
• /
• 제8권1호
• /
• pp.32-41
• /
• 2004

목적 : MnPC의 자기이완성질을 살펴보고, 토끼의 간에 이식한 VX2 암종을 이용해 자기공명영상에서 간의 조영증강형태를 관찰하고자하였다. 또한 간세포 특이성 조영제 사용 시와 비교하여 MnPC의 조직특이성 조영제로서의 가능성을 탐색해 보고자 하였다. 대상 및 방법 : 조영제 합성시 상자성 원소의 배위자로 phthalocyanine(PC)를 선택하였다. 2.01 g (5.2 mmol)의 phthalocyanine을 0.37g(1.4 mmol)의 manganese chloride와 $310^{\circ}C$에서 36시간동안 반응시킨 후 혼합물을 크로마토그래피 (CHC13: CH3OH=98:2, volume ratio)로 정제하여 2000 달톤의 분자량을 갖는 1.04 g $(46\%)$의 MnPC를 얻었다. 자기이완율은 MnPC를 0.1 mmol로 희석시켜 1.5 T (64 MHz)에서 측정하였다. VX2 암종은 토끼의 간실질 내에 종양세포 부유액을 주입해 실험적으로 유발시켰다. 모든 영상은 1.5 T MR장비에서 무릎관절코일을 사용하여 획득하였다. 본 연구에서 새로 개발된 거대분자 자기공명영상 조영제인 MnPC (4m-mol/kg)와 간세포 특이성 조영제인 Mn-DPDP (0.01 mmol/kg)가 사용되었으며 이들 조영제는 토끼의 이정맥을 통해 주입되었다. T1 강조영상은 스핀에코 (TR/TE=516/14 msec)와 고속다면회손경사회복 (TR/TE=80/4 m-sec, flip angle $60^{\circ}$)을 사용하여 얻었고, T2 강조영상의 획득을 위해서는 고속스핀에코 (TR/TE=1200/85 m-sec)를 사용하였다. 결과 MnPC의 1.5T (64MHz)에서의 자기이완율은 $R1=7.28\;mM^{-1}S^{-1}$, $R2=55.56\;mM^{-1}S^{-1}$ 이었고, MnPC의 높은 T2 자기이완율은 T2 강조영상에서의 정상 간실질의 신호강도를 감소시켜 간실질과 VX2 암종의 구분을 쉽게 하였다. MnPC 주입시 T1 강조영상에서는 간세포 특이성 조영제의 주입시보다 종양의 경계가 명확하였고, 조영증강은 주입후 최소한시간 이상 높게 유지되었다. 결론 : MnPC가 간세포로 흡수되어 담관으로 배설된다는 사실은 Mn-DPDP와 유사한 특성이며 이는 MnPC가 새로운 간특이성 조영제임을 확인시켜 준다. 또한 MnPC의 R2값이 기존의 조영제에 비해 매우 크다는 사실은 T1 조영제로서 뿐만 아니라 T2 조영제로서의 사용 가능성을 보여준다. 이러한 사실들을 좀더 정확하게 뒷받침하기 위해서는 임상적으로 사용되기 이전에 생체 내 그리고 시험관내 연구가 더 필요하며 다른 동물모델에서의 추가적인 연구가 요구된다.

• 한국산림과학회지
• /
• 제19권1호
• /
• pp.1-23
• /
• 1973

우리나라에서 식물생장(植物生長)이 가장 나쁜 니암지대(泥岩地帶) 황폐림지(荒廢林地)에 지피식생(地被植生)을 조성(造成)시키기 위하여 지피식생(地被植生) 조성시험(造成試驗)을 실시(實施)한 결과(結果)는 다음과 같다. 1. 객토량시험(客土量試驗)에 있어서 객토(客土)는 두께 15cm이상을 하여야만 객토(客土)의 효과(効果)를 인정(認定)할 수있었고, 10cm의 객토(客土)를 하고서도 시비(施肥)를 하지 않으면 생장(生長)이 불량(不良)하여 1cm 객토후(客土後) 비료(肥料)를 충분(充分)히 사용(使用)한 구(區)보다 못하였다. 또 파종혈(播種穴)의 깊이에 있어서 30cm구(區)와 40cm구(區)와는 그 성적차(成績差)를 인정(認定)할 수가 없었다. 식생대피복구(植生袋被覆區)와 무피복구(無被覆區)는 식물(植物)이 발아당시(發芽當時)에는 종자(種子)의 유실여부(流失如否)와 유시(幼時) 생장상(生長上)의 차(差)가 다소(多少)있었으나 가을 성적(成績) 결과(結果)는 차(差)를 인정(認定)할 수 없어서, 이것을 종합(綜合)하여 보면 객토(客土)는 10cm이상(以上)이고 파종혈(播種穴)($30cm{\times}30cm$)당(當) 30g(22:22:11 복비(複肥) 55g)의 시비(施肥)를 하여야 한다. 2. 객토파종별(客土播種別) 시험(試驗)에 있어서 화강암풍화토(花崗巖風化土), 응회암풍화토(凝灰岩風化土), 니암풍화토별(泥岩風化土別) 성적(成績)은 고도(高度)의 유의차(有意差)가 없어고, 각종녹화자재별(各種綠化資材別) 처리(處理)에서도 모연공구(毛筵工區)에서만 1%의 유의차(有意差)를 나타내었다. 이것을 종합(綜合)하면 본 바닥 산록(山麓)의 성취(成就)된 니암풍화토(泥岩風化土)를 객토(客土)로 사용(使用)하는 것이 효과적(効果的)이며 모연공구(毛筵工區)가 좋았다. 3. 니암지대(泥岩地帶)의 임지비암(林地肥岩)임지에는 기존임목(旣存林木)(소나무, 해송)이 1ha당(當) 2,000~3,000본(本) 산재(散在)되어 있으므로 1ah당(當) 22:22:11 복합비료(複合肥料)를 성분량(成分量)으로 110kg을 시용(施用)한 결과(結果) 시비당년(施肥當年)에는 차(差)를 인정(認定)할수 없었으나 다만 엽색(葉色)이 농록색(濃綠色)을 정(呈)하고 엽장(葉長)이 30~40% 더 신장(伸張)하였고 사방오리나무에 있어서 14:37:12 및 9:12:3 복비(複肥)를 본당성분량(本當成分量)으로 20g 구(區)와 40g 구(區)로 나누어 시비(施肥)한 결과(結果) 40g구(區)가 월등(越等)히 생장(生長)이 양호(良好)하였으며 비종간(肥種間)에는 차(差)이를 인정(認定)할수 없었다. 4. 임목(林木)의 근계신장상황(根系伸張狀況)은 소나무는 40년(年)을 자라도 니암(泥岩)을 뚫고 생장(生長)하는 직근신장(直根伸張)은 15cm에 불과(不過)하나 곰솔은 23cm까지 주근(主根)이 신장(伸張)할 수가 있으므로 소나무보다 해송의 직근(直根) 신장력(伸張力)이 강(强)하다. 측근전장(側根全長)은 소나무에서 20m 해송에서 13m이였고, 아까시아나무는 식재당시(植栽當時)에 길이에서 더밑으로 암석을 뚫지 못하고 측근(側根)만 발달(發達)하여 비교적(比較的) 수분(水分)이 보지(保持)되는 소나무밑으로 신장(伸張)하는 것이 통례(通例)이였으며, 니암잔적토(泥岩殘積土)에서는 8~10년(年)만에 고사(枯死)되고 만다. 한편 소나무의 수형(樹型)은 편편상(偏偏狀)인데 해송은 삼각형(三角形)에 수형(樹型)을 이루고 있는 것이 특이하다. 이상(以上)의 사실(事實)을 종합(綜合)하면 인공(人工) 조림시(造林時) 충분(充分)한 식혈(植穴)을 파주지 않으면 임목(林木) 생육(生育)이 어려우므로 충분(充分)한 식혈(植穴)과 비료(肥料)를 시용(施用)하여야만 니암지대(泥岩地帶) 황폐림지(荒廢林地)를 복구(復舊)할수 있을것이다.