• Design & Manufacturing
• /
• 제6권2호
• /
• pp.1-5
• /
• 2012

Weld line in injection molded part is one of the defects in injection molding process. Weld line deteriorates not only appearance quality but mechanical property. In this study, ABS and PP were used as experimental materials. And weld line length, depth and strength have been examined according to the injection molding conditions. As the results of experimental studies, weld line length increased as flow rate increases for all materials. And the flow rate is most influenced to the creation of weld line length. Also weld line strength increased, as flow rate and melt temperature increase for all materials. The whole experiment results was similar to CAE analysis results.

• 소성∙가공
• /
• 제20권2호
• /
• pp.173-178
• /
• 2011

Environmental Stress Cracking(ESC) is one of the most common causes of unexpected brittle failure of thermoplastic polymers. The exposure of polymers to liquid chemicals tends to accelerate the crazing process, initiating crazes at stresses that are much lower than the stress causing crazing in air. In this study, ESC of acrylonitirile butadiene styrene(ABS) was investigated as a function of the molding conditions such as injection velocity, packing pressure, and melt temperature. A constant strain was applied to the injection molded specimens through a 1.26% strain jig and a mixture of toluene and isopropyl alcohol was used as the liquid chemical. In order to examine the effects of the molding conditions on ESC, an experimental design method was adopted and it was found that the injection velocity was the dominant factor. In addition, predictions from numerical analyses were compared with the experimental results. It was found that the residual stress in the injection molded part was associated with the environmental stress cracking resistance (ESCR).

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.74.2-74.2
• /
• 2011

A simulation study on synthesis gas process in GTL process was carried out in order to find optimum operation conditions for GTL (gas-to-liquid) pilot plant design. Optimum operating conditions for synthesis gas process were determined by changing reaction variables such as feed temperature and pressure. During the simulation, overall synthesis process was assumed to proceed under steady-state conditions. It was also assumed that physical properties of reaction medium were governed by RKS (Redlich-Kwong-Soave) equation. The effect of temperature and pressure on synthesis gas process $H_2$/CO ratio were mainly examined. Simulation results were also compared to experimental results to confirm the reliability of simulation model. Simulation results were reasonably well matched with experimental results.

• Asian-Australasian Journal of Animal Sciences
• /
• 제14권6호
• /
• pp.844-849
• /
• 2001

This study was carried out to determine the optimum conditions for cholesterol removal from homogenized milk by treatment with saponin using a response surface methodology (RSM). The effects of temperature, reaction time, and amounts of celite or saponin added on cholesterol removal from milk were investigated. The level of cholesterol removal from milk increased with saponin concentration and varied from 57.4 to 73.3%. The optimum reaction time, amount of celite addition determined by a partial differentiation of the model equation, and amount of saponin addition were 30min, 0.95% and 1.5%, respectively. Under these conditions, the predicted cholesterol removal by RSM was estimated to be 73.4%. The experimental removal value was 73.7%. Thus, there was no appreciable difference between the experimental value and the predicted value based on RSM.

• 한국자동차공학회논문집
• /
• 제7권7호
• /
• pp.104-112
• /
• 1999

An experimental study for reducing the exhaust hydrocarbon emission at spark ignition engine using timed secondary air injection is carried out . In this study, secondary air injection timings and durations are controlled to decrease the hydrocarbon emission and to increase exhaust gas temperature at cold and warm-up engine conditions. The hydrocarbon reduction rate and exhaust gas temperature are compared between timed secondary air injection and continuous air injection. The optimum secondary air injection timing for reducing the hydrocarbon emission is at the exhaust valve open timing. At some engine conditions , the hydrocarbon emissions are decreased to 10% of engine raw values and exhaust gas temperatures increase by 20$0^{\circ}C$ with times secondary air injection . Timed secondary air injection has more hydrocarbon reduction rate that continuous secondary air injection except some engine conditions.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2001년도 학술발표회 발표논문집
• /
• pp.185-188
• /
• 2001

In this study, the characteristics of freezing and thawing resistance, the compressive strength, and the change in height of cement mortar according to a steam and taler curing conditions has been studied. To this end, the major test variables include the period of the early curing, curing temperature and the later curing. The strength test as well as volume variousness have been conducted to explore the characteristics of freezing and thawing resistance on the curing conditions. The experimental results can be efficiently used to improve the characteristics of freezing and thawing resistance for concrete products carrying steam curing.

• 약학회지
• /
• 제44권6호
• /
• pp.545-551
• /
• 2000

Magnesium trisilicate was prepared by reacting Magnesium sulfate solution with Sodium silicate solution in this study. The optimum synthesis conditions base on the yield of the product were established by applying Box-Wilson experimental design. It was found that the optimum synthesis conditions of Magnesium trisilicate were as follows; Reacting temperature : $57{\sim}90^{\circ}C$, Concentration of reactant solution : $19.1{\sim}20.0%$, Molar concentration ratio of two reactants : [Sod.silicate]/[Mg.sulfate] : $1.47{\sim}1.80$, Temperature of washing water : $45{\sim}48^{\circ}C$, Drying temperature : $65{\sim}82^{\circ}C$. The antacidic capacity of the five Magnesium trisilicate samples which shows the maximum antacidic efficacy was tested by pharmacopeia acid consuming capacity test. The five Magnesium trisilicate samples were identified by chemical analysis.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.476-479
• /
• 1997

A Knowledge of friction force in pneumatic cylinders makes it possible to improve cylinder description during simulation and to asses performance under changing operating conditions more accurately. Such knowledge is particularly useful, for example, when modeling continuous pneumatic positioning systems or predicting the operating conditions under which stick slip may occur, as well as in establishing preventive maintenance procedures for pneumatic cylinders. Friction force depends on a number of factors, including operating pressure, seal running speed on the cylinder barrel and rod, barrel material and surface roughness, seal dimensions and profile, seal material, lubrication conditions, cylinder distortion during assembly, and the operating temperature of cylinder components. This paper shows a system for measuring the friction force caused by a seal used in pneumatic cylinders. Results of experimental tests show that seal friction forces for grease lubricated service are clearly dependent on speed and pressure and are les sensitivity to other parameter. i.e., barrel material and roughness, seal material, and profile.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 추계학술발표회논문집(1)
• /
• pp.242-247
• /
• 1996

Flow oscillations in boiling channels induces a drastic reduction of the (critical heat flux) CHF or premature burnout. However, most of CHF works and correlations have been focused on stable flow conditions without considering flow oscillation. Therefore to improve the understanding on flow oscillation CHF, in this paper a new CHF correction factor to predict the CHF values under flow oscillation conditions has been developed from 126 experimental data. Also to investigate the dominant factor on flow oscillation CHF parametric trends are analyzed by using the developed correction factor. The overall mean accuracy ratio of the developed correction factor is 1.033 with a standard deviation of 0.195. The RMS errors 0.198. Its assessment shows that the predictions agree well with the experimental data within 25% error bounds.

• Journal of Mechanical Science and Technology
• /
• 제20권5호
• /
• pp.692-709
• /
• 2006

Nucleate pool boiling experiments with constant wall temperature were performed using pure R1l3 for subcooled, saturated, and superheated pool conditions. A microscale heater array and Wheatstone bridge circuits were used to maintain the constant wall temperature and to measure the instantaneous heat flow rate accurately with high temporal and spatial resolutions. Images of bubble growth were taken at 5,000 frames per second using a high-speed CCD camera synchronized with the heat flow rate measurements. The bubble geometry was obtained from the captured bubble images. The effect of the pool conditions on the bubble growth behavior was analyzed using dimensionless parameters for the initial and thermal growth regions. The effect of the pool conditions on the heat flow rate behavior was also examined. This study will provide good experimental data with precise constant wall temperature boundary condition for such works.