• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2002년도 추계 학술발표회 논문집
• /
• pp.239-246
• /
• 2002

Viscoelastic dampers are known effective devices for response reduction under earthquakes and winds. This study addresses how to design the optimum viscoelastic dampers installed at the full scale five-story steel building and novel approach to carry out the experimental work to verify the damper performance. First, an exciter of hybrid mass-type actuator is designed, which can move the building and its mathematical model is derived. The integrated system of building-actuator is experimentally analyzed for mathematical model. Second, convex model is applied for the prediction of required additional damping ratios to reduce responses below a specified target level. Chevron-type viscoelastic dampers are manufactured and installed at the first and second inter-stories, which are optimum places for response reduction. Sine-sweep and white noise excitations, which are generated by the hybrid mass-type actuator, are applied to the full scale building without and with dampers for performance verification. The transfer function of the building with four dampers, two of them installed at each first and second inter-story, are found to be lower than that of the building with two dampers installed at the first inter-story

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제23회 추계학술대회 논문집
• /
• pp.229-234
• /
• 2004

The objective of the present study is to conduct model combustion tests for double swirl coaxial injectors to identify their combustion stability characteristics. Gaseous oxygen and mixture of methane and propane have been used as simulant propellants. Two model chambers tuned to the If acoustic resonance mode of a full-scale thrust chamber were manufactured to be used as a combustion cylinder. The main idea of the experiment is that the mixing mechanism is considered as a dominant factor significantly affecting combustion instability in a full-scale thrust chamber. Self-excited dynamic pressure values in a model chamber show different combustion stability zones with respect to a recess number. Upon test results, couplings between combustion conditions and the IT acoustic resonance mode become strengthened with the increase of a recess length.

• 한국해양공학회지
• /
• 제22권3호
• /
• pp.64-70
• /
• 2008

A full-scale field experiment is an important part in the design of ships and offshore structures. Full-scale tests in the ice-covered sea, however, are usually very expensive and difficult tasks. Model tests in a refrigerated ice tank may substitute this difficulty of full-scale field tests. One of the major tasks to perform proper model tests in an ice towing tank is to select a realistic material for model ice which shows correct similitude with natural sea ice. This study focuses on the testing material properties and the selection of model ice material which will be used in an ice model basin. The first Korean ice model basin will be constructed at the Maritime & Ocean Engineering Research Institute (MOERI) in 2009. With an application to the MOERI ice model basin, in this study the material properties of EG/AD/S model ice of IOT (Institute for Ocean Technology) Canada, were tested. Through comprehensive bending tests, the elastic modulus and the flexural strength of EG/AD/S model ice were evaluated and the results were compared with published test results from Canada. Instead of using an ice model basin, a cold room facility was used for making a model ice specimen. Since the cold room adopts a different freezing procedure to make model ice, the strength of the model ice specimen differs from the published test results. The reason for this difference is discussed and the future development for a making model ice is recommended.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제13권1호
• /
• pp.57-64
• /
• 2021

Maneuvering motions of a ship in calm water are studied through the concept of MMG model. Governing forces are defined by the use of available empirical formulae that require only main ship particulars as input variables. In order to validate the calculation tool, a full-scale sea experiment was carried out in Osaka Bay using a 17-m twin-screw passenger ferry. Test execution and data measurement were performed through the utilization of an autopilot control unit and satellite compass. The result of a straight running test confirms the acceptable accuracy in addressing the surge motion problem. Reasonable agreement between simulation and experiment is also confirmed for 5°/5° and 10°/10° zig-zag tests despite the strong environmental disturbance. The current model can generally represent the subject ship maneuvering motions and is promising for the application to other ship hulls.

• Wind and Structures
• /
• 제15권1호
• /
• pp.43-64
• /
• 2012

Many potential small wind turbine locations are near obstacles such as buildings and shelterbelts, which can have a significant, detrimental effect on the local wind climate. A neural network-based model has been developed which predicts mean wind speed and turbulence intensity at points in an obstacle's region of influence, relative to unsheltered conditions. The neural network was trained using measurements collected in the wakes of 18 scale building models exposed to a simulated rural atmospheric boundary layer in a wind tunnel. The model obstacles covered a range of heights, widths, depths, and roof pitches typical of rural buildings. A field experiment was conducted using three unique full scale obstacles to validate model predictions and wind tunnel measurements. The accuracy of the neural network model varies with the quantity predicted and position in the obstacle wake. In general, predictions of mean velocity deficit in the far wake region are most accurate. The overall estimated mean uncertainties associated with model predictions of normalized mean wind speed and turbulence intensity are 4.9% and 12.8%, respectively.

• 수산해양기술연구
• /
• 제51권2호
• /
• pp.203-211
• /
• 2015

The purpose of this study is to identify the flow resistance of the bottom pair trawl nets. The bottom pair trawl nets being used in fishing vessel (100G/T, 550ps) was selected as a full-scale net, and 1/10, 1/25 and 1/50 of the model nets were made. Converted into the full-scale net by Tauti's modeling rule and Kim's modeling rule, when resistance coefficient k of each net was calculated by substituting into above equation for flow resistance R and wall area of nets S values of each net ${\upsilon}$. Because resistant coefficient k decreases exponentially according as flow velocity ${\upsilon}$ increases to make $k=c{\upsilon}^{-m}$, c and m values of each net were compared. As a result, as the model was smaller, c and m values was smaller in the two rule into standard of 1/10 model value, decrease degree of 1/25 model was almost same in the two rule, decrease degree of 1/50 model was very big in Tauti's modeling rule. Therefore, in the result of experiment, because average of c and m values for similarly 1/10 and 1/25 model were given $c=4.9(kgf{\cdot}s^2/m^4)$ and m=0.45, R (kgf) of bottom pair trawl net could show $R=4.9S{\upsilon}^{1.55}$ using these values. As in the order of cod-end, wing and bag part for 1/25 and 1/50 model net were removed in turn, measured flow resistance of each, converted into the full-scale, total resistance of the net and the resistance of each part net were calculated. The resistance ratio of each part for total net was not same in 1/25 and 1/50 model each other, but average of two nets was perfectly same area ratio of each part as the wing, bag and cod-end part was 43%, 45% and 12%. However, the resistance of each part divided area of the part, calculated the resistance of per unit area, wing and bag part were not big difference each other, while the resistance of cod-end part was very large.

• Structural Engineering and Mechanics
• /
• 제60권4호
• /
• pp.655-665
• /
• 2016

This paper aims to develop models to accurately predict the behavior of fresh concrete exposed to vibration using artificial neural networks (ANNs) model and regression model (RM). For this purpose, behavior of a full scale precast concrete mold was investigated experimentally and numerically. Experiment was performed under vibration with the use of a computer-based data acquisition system. Transducers were used to measure time-dependent lateral displacements at some points on mold while both mold is empty and full of fresh concrete. Modeling of empty and full mold was made using both ANNs and RM. For the modeling of ANNs: Experimental data were divided randomly into two parts. One of them was used for training of the ANNs and the remaining part was used for testing the ANNs. For the modeling of RM: Sinusoidal regression model equation was determined and the predicted data was compared with measured data. Finally, both models were compared with each other. The comparisons of both models show that the measured and testing results are compatible. Regression analysis is a traditional method that can be used for modeling with simple methods. However, this study also showed that ANN modeling can be used as an alternative method for behavior of fresh concrete exposed to vibration in precast concrete structures.

• 수산해양기술연구
• /
• 제32권1호
• /
• pp.1-6
• /
• 1996

Towing tension of the model nets were determined by the load cell(O~20kg, 20DBBP) in front of W$T_mA$ = 1.57 . $V^1.86$ (unit: kg, mlsec) $T_mB$= 1.58 . $V^1.90$ 2. The towing tension of the full scale net was almost coincided with the results obtained by the model experiment. The towing tension(T) can be expressed as a function of the towing veJocity(V) as T=479$V^1.75$(unit: kg, k't)

• Geomechanics and Engineering
• /
• 제24권1호
• /
• pp.29-42
• /
• 2021

The utilization of buildings can be improved by extending them vertically. However, the added load of the extension might require building foundations to be underpinned; otherwise, the loads on the foundations might exceed their bearing capacity. In this study, a preloading method was presented aiming at transferring partial loads from existing piles to underpinning piles. A pneumatic-type model preloading device was developed and used to carry out centrifuge experiments to evaluate the load-displacement behavior of piles, the pile-soil interaction during preloading, and the additional loading caused by vertical extension. The results showed that the preloading devices effectively transfer load from existing piles to underpinning piles. In the additional loading test of group piles, the load-sharing ratio of a pile increased with its stiffness. The load-sharing ratio of a preloaded micropile was less than that of a non-preloaded micropile as a result of the reduction in axial stiffness caused by preloading before additional loading. Therefore, a slight reduction of the load-sharing capacity of an underpinning pile should be considered if the preloading method is applied. Further, two full scale preloading devices was developed. The devices preload underpinning piles and thereby produce reaction forces on a reaction frame to jack existing piles upward, thus transferring load from the existing piles to the underpinning piles. Specifically, screw-type and hydraulic-jack type devices were developed for the practical application of foundation underpinning during vertical extension, and their operability and load transfer effect verified via full-scale structural experiments.

• 수산해양기술연구
• /
• 제47권4호
• /
• pp.281-289
• /
• 2011

The purpose of this study is to identify the flow resistance of the bottom trawl net. The bottom trawl net being used in the training ship of Chonnam National University was selected as a full-scale net, and model nets such as 1/10, 1/25 and 1/50 of the actual net were made. Total resistance of the net part, the height of the net mouth and the flow resistance of components of the net such as wing, bag and cod-end part was measured, converted into full-scale and compared. Additionally, the model rule of Tauti (1934), which has been most frequently used in fishing net modeling experiments, was applied to interpret flow resistance and scale effect of model experiment was investigated. Presumed that the flow resistance R is $R=kS{\upsilon}^2$ against the flow velocity of each net ${\upsilon}$, resistance coefficient k was calculated by substituting R, ${\upsilon}$ and S of the net. From the result, it was found that k decreases exponentially when u increases which makes $k=c{\upsilon}^{-m}$. Whereas m of each net is ranged between 0.13-0.16 and there was not significant difference between nets. c does not show big difference in 1/10 and 1/25 model and the value itself was relatively bigger than in 1/50 model. The height of the net mouth of 1/25 and 1/50 model net h decreases exponentially according as ${\upsilon}$ increases to make $h=d{\upsilon}^{-n}$. Whereas d and n values were almost same in two nets. Additionally, when resistance of cod-end, wing and bag part in 1/25 and 1/50 model nets, both nets showed big resistance in bag part when flow is 1m/s as more than 60%. Wing and cod-end part showed almost same value or wing part had little bit larger value. On the other hand, when reviewing the reasons why both models showed difference in 1/50 model while c value against the resistance coefficient k did not show big difference in 1/10 and 1/25 model, it is inferred that the difference occurred not from material difference but from the difference in net size according to scale. It was judged that they are the scale effects concomitant to the model experiments.