• 한국수자원학회논문집
• /
• 제52권5호
• /
• pp.313-323
• /
• 2019

대심도 터널은 기 개발된 도시의 부족한 배수관망 능력을 보강하기 위하여 지하에 설치하는 대규모 도시홍수 배제 시설물로 역 사이펀 관로 형태를 하고 있는 시설물이다. 대심도 터널과 같은 구조에서는 하류에서 발생한 불규칙 단파에 의하여 터널의 수리적 안정성에 문제가 발생한다. 본 연구에서는 국내 최초로 건설 중인 '신월 빗물저류배수시설'의 수리적 안정성에 불규칙 단파가 미치는 영향을 알아보기 위하여 다양한 홍수유입 시나리오에 대하여 수리모형실험을 실시하였다. 본 연구에서 수행한 수리모형실험 결과 하류에서 발생한 불규칙 단파가 상류로 이동하면서 관 내 포집되어 압축상태인 공기덩어리를 밀어내는데, 이 공기덩어리가 상류 수직유입구를 통하여 급배기 되는 과정에 수직유입구를 질식시키고 홍수유입을 차단하여 월류가 발생하는 것으로 판단된다. 또한 불규칙 단파의 이동속도를 분석한 결과 불규칙 단파가 이동하면서 에너지를 전달하고 이때 관 내 압력 상승 및 불규칙 단파의 속도 증가분이 발생하는 것으로 판단된다. 대심도 터널의 수리적 안정성에 중요한 역할을 하는 불규칙 단파의 크기 및 속도 예측을 위한 추가 연구가 필요할 것으로 판단된다.

• Ocean and Polar Research
• /
• 제42권2호
• /
• pp.171-178
• /
• 2020

R/V EARDO, commissioned in 1992, has successfully carried out ocean research campaigns in Korean jurisdictional and adjacent waters, including continental margins and coastal zones within the Korean Exclusive Economic Zone (EEZ), for 29 years. However, it will soon be reaching the end of its useful service life. A replacement for R/V EARDO is urgently needed to ensure the safety of vessel itself and its crews, and efficient ship operation and maintenance, as well as to meet modern scientific mission requirements (SMRs). Basic specifications for a replacement ship have been devised and reviewed over the past nine months. A test of the proposed hull form was also performed. The total tonnage of the proposed vessel is approximately 740 tons, and the overall length and width are 62.0 and 11.6 m, respectively. The new ship will thus be 73% larger than the current R/V EARDO; in particular, the research workspace will be 4.4 times larger. The major design priorities are the propulsion system, efficiency of radiated noise and vibration control, and the dynamic positioning system. An environmentally friendly emission system, meeting International Maritime Organization (IMO) Tier III regulations, will be installed in the third exhaust pipe. Various wet and dry lab spaces as well as 32 different scientific instruments have also been considered in the ship design.

• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.88-97
• /
• 2012

To measure the traffic pollutants with high temporal and spatial resolution under real conditions, a mobile emission laboratory (MEL) was designed. The equipment of the mini-van provides gas phase measurements of CO, NOx, CO2 and THC (Total hydrocarbon), and number density & size distribution measurements of fine and ultra-fine particles by a fast mobility particle sizer (FMPS) and a condensation particle counter (CPC). The inlet sampling port above the bumper enables the chasing of different type of vehicles. This paper introduces the technical details of the MEL and presents data from the experiment in which a MEL chases a city bus fuelled by diesel, DME and Bio-diesel. The dilution ratio was calculated by the ratio of ambient NOx and tail-pipe NOx. Most particles from the bus fuelled by diesel were counted under 300 nm and the peak concentration of the particles was located between 30 and 60 nm. However, most particles in the exhaust of the bus fuelled by DME were nano-particles (diameter: less than 50 nm). The bus fuelled by Bio-diesel shows less particle emissions compare to diesel bus due to the presence of the oxygen in the fuel.

• 한국전산유체공학회지
• /
• 제9권3호
• /
• pp.49-56
• /
• 2004

A heated and expanded helium is used to pressurize liquid propellants in propellant tanks of propulsion system of liquid propellant launch vehicles. To produce a heated and expanded helium, an hot-gas heat exchanger is used by utilizing heat source from an exhausted gas, which was generated in a gas generator to operate turbine of turbo-pump and dumped out through an exhaust duct of engine. Both experimental and numerical approaches of hot-gas heat exchanger design were conducted in the present study. Experimentally, siliconites - electrical resistance types - were used to simulate the full heat condition instead of an exhausted gas. Cryogenic heat exchangers, which were immersed in a liquid nitrogen pool, were used to feed cryogenic gaseous helium in a hot-gas heat exchanger. Numerical simulation was made using commercially utilized solver - Fluent V.6.0 - to validate experimental results. Helically coiled stainless steel pipe and stainless steel exhausted duct were consisted of tetrahedron unstructured mesh. Helium was a working fluid Inside helical heat coil and regarded as an ideal gas. Realizable k-』 turbulent modeling was adopted to take turbulent mixing effects in consideration. Comparisons between experimental results and numerical solutions are Presented. It is observed that a resulted hot-gas heat exchanger design is reliable based on the comparison of both results.

• 대한기계학회논문집B
• /
• 제39권2호
• /
• pp.177-182
• /
• 2015

디젤 엔진과 산업용 보일러에서의 질소산화물(NOX) 배출은 환경오염을 유발시키는 주요물질 중의 하나이다. 이러한 질소산화물 발생을 저감시키기 위한 방법으로 후처리 기술 중의 하나인 우레아 선택적 촉매 환원(Urea-SCR)기술이 널리 사용되고 있다. 본 연구에서는 선박용 디젤엔진의 배기가스 조건을 모사한 실험실 스케일의 실험장치를 통해 우레아 수용액의 열분해 특성에 대해 고찰하였다. 40 wt. %의 우레아 농도를 가진 우레아 수용액을 사용하였고, 모사가스의 온도와 유속변화, 우레아 수용액의 유량에 따른 총 전환율 뿐만 아니라 암모니아($NH_3$)와 이소시안산(HNCO)의 전환율 차이를 알아보았다. $210^{\circ}C$와 $250^{\circ}C$ 모사가스 온도에서 체류시간에 따라 암모니아의 전환율이 이소시안산의 전환율보다 높게 나타남을 확인하였다.

• 한국추진공학회지
• /
• 제18권2호
• /
• pp.86-92
• /
• 2014

나로우주센터에 구축되는 연소기 연소시험설비(CCTF)에는 한국형발사체(KSLV-II)에 적용된 터보펌프식 엔진의 가스발생기 시험시 생성되는 연료과잉가스를 연소시키기 위한 후연소시스템이 포함되어 있다. 후연소시스템은 $O_2$와 $CH_4$ 가스를 공급받아 연료과잉가스를 소모시킨다. 본 연구는 연소기 연소시험설비의 상세설계 자료를 바탕으로 후연소시스템의 가스공급시스템에 대해 AMESim 상용프로그램을 이용하여 해석하였다. 그 결과 상세설계에 적용된 레귤레이터, 공급배관, 오리피스크기 등으로 가스사용량을 예측하고, 상세설계의 타당성을 검증하였다.

• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.65-72
• /
• 2011

In this study, the numbers, sizes of particles from a single cylinder direct injection spark-ignition (DISI) engine fuelled with gasoline and LPG are examined over a wide range of engine operating conditions. Tests are conducted with various engine loads (2~10bar of IMEP) and fuel injection pressures (60, 90, and 120 bar) at the engine speed of 1,500 rpm. Particles are sampled directly from the exhaust pipe using rotating disk thermodiluter. The size distributions are measured using a scanning mobility particle sizer (SMPS) and the particle number concentrations are measured using a condensation particle counter (CPC). The results show that maximum brake torque (MBT) timing for LPG fuel is less sensitive to engine load and its combustion stability is also better than that for gasoline fuel. The total particle number concentration for LPG was lower by a factor of 100 compared to the results of gasoline emission due to the good vaporization characteristic of LPG. Test result presents that LPG for direct injection spark ignition engine help the particle emission level to reduce.

• Journal of Advanced Marine Engineering and Technology
• /
• 제40권9호
• /
• pp.780-785
• /
• 2016

선박의 연료로 이용되는 중유는 지구 온난화를 일으키는 유해가스를 배출한다. 이를 저감하기 위해 친환경선박으로 표현되고 있는 녹색선박이 등장하게 되었고, 천연가스를 연료로 하는 액화천연가스(LNG) 연료 선박이 대표적인 사례이다. 본 논문에서는 LNG 선박에 사용되는 극저온 환경에서 고압 하중을 받는 기화기와 출입구 배관의 구조 건전성을 ASME 코드에 따라 평가하고 실용화한 최초의 사례이다. 기화기와 배관은 유한요소법을 사용하여 구조해석을 수행하였다. 기화기는 등가응력을 바탕으로 ASME Section VIII Division 2에 제시된 허용응력과 비교하여 건전성 평가를 수행하였고, 배관은 성분별 응력을 조합하여 ASME B31.3에 제시된 허용응력과 비교 및 건전성 평가를 수행하였다. 각 하중에 대한 구조물들의 응력 결과는 허용응력 범위 이내에 있으므로 구조적 건전성을 유지하는 것으로 평가되었다.

• 한국수소및신에너지학회논문집
• /
• 제31권2호
• /
• pp.169-176
• /
• 2020

There is a growing interest in hydrogen energy utilization since an alternative energy development has been demanded due to the depletion of fossil fuels. Hydrogen is produced by the reforming reaction of natural gas and biogas, and the electrolysis of water. An solid oxide electrolyte cell (SOEC) is reversible system that generates hydrogen by electrolyzing the superheated steam or producing the electricity from a fuel cell by hydrogen. If the water can be converted into steam by waste heat from other processes it is more efficient for high-temperature electrolysis to convert steam directly. The reasons are based upon the more favorable thermodynamic and electrochemical kinetic conditions for the reaction. In the present study, steam at over 180℃ and 3.4 bars generated from a boiler were converted into superheated steam at over 700℃ and 3 bars using a cylindrical steam superheater as well as the waste heat of the exhaust gas at 900℃ from a solid refuse fuel combustor. Superheated steam at over 700℃ was then supplied to a high-temperature SOEC to increase the hydrogen production efficiency of water electrolysis. Computational fluid dynamics (CFD) analysis was conducted on the effects of the number of 90° elbow connector for piping, insulation types and insulation layers of pipe on the exit temperature using a commercial Fluent simulator. For two pre-heater injection method of steam inlet and ceramic wool insulation of 100 mm thickness, the highest inlet temperature of SOEC was 744℃ at 5.9 bar.

• Nuclear Engineering and Technology
• /
• 제53권5호
• /
• pp.1436-1445
• /
• 2021

To obtain the dynamic characteristics of reactor secondary circuit under transient conditions, the system analysis program was developed in this study, where dynamic models of secondary circuit were established. The heat transfer process and the mechanical energy transfer process are modularized. Models of main equipment were built, including main turbine, condenser, steam pipe and feedwater system. The established models were verified by design value. The simulation of the secondary circuit system was conducted based on the verified models. The system response and characteristics were investigated based on the parameter transients under emergency shutdown and overload. Various operating conditions like turbine emergency shutdown and overspeed, condenser high water level, ejector failures were studied. The secondary circuit system ensures sufficient design margin to withstand the pressure and flow fluctuations. The adjustment of exhaust valve group could maintain the system pressure within a safe range, at the expense of steam quality. The condenser could rapidly take out most heat to avoid overpressure.