• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.905-908
• /
• 2007

The purpose of this work is to obtain fundamental data about fatigue crack detection of the welded exhaust flange by using the AE method. The acoustic emission method as a nondestructive evaluation is one of high technical test for realtime monitoring in the dangerous industry fields. Signal analysis of both AE sensor and accelerometer for fatigue crack failure are presented in this paper.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2005년도 제31회 KOSCO SYMPOSIUM 논문집
• /
• pp.104-109
• /
• 2005

This paper describes the effect of the split injection on combustion and emission characteristics in a common rail diesel engine at various operating conditions. The combustion pressures and exhaust emissions such as $NO_x$ and soot were measured at various split injection timings. The experimental apparatus of this study is composed of 4 cylinder engine installed with piezoelectric pressure sensor, EC dynamometer, and exhaust gas analyzer for the measurement of $NO_x$, CO, HC and soot emissions. Results show that the split injection has a great effect on reducing the rapid premixed combustion and $NO_x$ emissions.

• 대한기계학회논문집B
• /
• 제28권7호
• /
• pp.857-862
• /
• 2004

HCCI engines take advantage of high compression ratio and heat release rate, they exhibit high efficiency in compression ignition engines. HCCI engines also utilize a lean air/fuel ratio resulting in low emissions of NOx and particulate matter(PM). The objective of this research is to determine the effects of EGR rate on the combustion processes of HCCI. For this purpose, a 4-cylinder, compression ignition engine was converted into a HCCI engine, and a heating device was installed to raise the temperature of the intake air and also to make it more consistent. In addition, a pressure sensor was inserted into each of the cylinders to investigate the differences in characteristics among the cylinders.

• 한국컴퓨터정보학회논문지
• /
• 제24권4호
• /
• pp.169-176
• /
• 2019

Wireless sensor networks are used to monitor and control areas in a variety of military and civilian areas such as battlefield surveillance, intrusion detection, disaster recovery, biological detection, and environmental monitoring. Since the sensor nodes are randomly placed in the area of interest, separation of the sensor network area may occur due to environmental obstacles or a sensor may not exist in some areas. Also, in the situation where the sensor node is placed in a non-relocatable place, some node may exhaust energy or physical hole of the sensor node may cause coverage hole. Coverage holes can affect the performance of the entire sensor network, such as reducing data reliability, changing network topologies, disconnecting data links, and degrading transmission load. It is possible to solve the problem that occurs in the coverage hole by finding a coverage hole in the sensor network and further arranging a new sensor node in the detected coverage hole. The existing coverage hole detection technique is based on the location of the sensor node, but it is inefficient to mount the GPS on the sensor node having limited resources, and performing other location information processing causes a lot of message transmission overhead. In this paper, we propose an Adjacent Matrix-based Hole Coverage Discovery(AMHCD) scheme based on connectivity of neighboring nodes. The method searches for whether the connectivity of the neighboring nodes constitutes a closed shape based on the adjacent matrix, and determines whether the node is an internal node or a boundary node. Therefore, the message overhead for the location information strokes does not occur and can be applied irrespective of the position information error.

• 한국세라믹학회지
• /
• 제41권2호
• /
• pp.97-101
• /
• 2004

W $O_{x}$-based semiconductor type thin film gas sensor was fabricated for the detection of N $O_{x}$ by reactive d.c. sputtering method. The relative oxidation state of the deposited W $O_{x}$ films was approximately compared by the calculation of the difference of the binding energy between Ols to W4 $f_{7}$2/ core level XPS spectra in the standard W $O_3$ powder of known composition. As the annealing temperature increased from 500 to 80$0^{\circ}C$, relative oxygen contents and grain size of the sputtered films were gradually increased. As the results of sensitivity ( $R_{gas}$/ $R_{air}$) measurements for the 5 ppm N $O_2$ gas, the sensitivity was 110 and the sensor showed recovery time as fast as 200 s. The other sensor properties were examined in terms of surface microstructure, annealing temperature, and relative oxygen contents. These results indicated that the W $O_3$ thin film with well controlled structure is a good candidate for monitoring and controlling of automobile exhaust.haust.t.t.t.

• 센서학회지
• /
• 제6권5호
• /
• pp.369-375
• /
• 1997

$SnO_{2}$에 $V_{2}O_{5}/ThO_{2}/Pd$를 도핑하여 제조된 센서는 약 $500^{\circ}C$의 높은 센서 온도에서 CO에 대해 우수한 선택도와 안전성 및 빠른 응답특성을 보였다. 특히, $V_{2}O_{5}$를 약 3.0 wt.% 첨가하여 선택도에 있어서 CO 감도에 대해 $NO_{x}$, $C_{3}H_{8}$, $CH_{4}$ 및 $SO_{2}$같은 많은 간섭가스들의 영향이 적음을 알았다. 센서 제조는 $V_{2}O_{5}$(3.0 wt.%), $ThO_{2}$(1.5wt.%), Pd(1.0 wt.%)의 촉매물질과 함께 기존에 잘 알려진 후막기술을 이용하였다. 일반적으로 연소배가스처럼 $NO_{x}$와 CO가 혼합되어 있는 복합가스의 경우, $SnO_{2}$계 반도체 센서로는 CO만의 검지는 $NO_{x}$ 간섭 때문에 대단히 어렵다. 본 센서는 공연비제어를 요하는 자동차나 보일러 시스템의 연소배가스의 측정과 감시에 사용할 수 있을 것이다.

• 한국가스학회지
• /
• 제22권2호
• /
• pp.78-83
• /
• 2018

이 논문은 디젤엔진 자동차의 EGR 및 공기 제어와 CPF 장치에 관련된 고장사례 연구이다. 첫 번째 사례는 엔진진공펌프 손상으로 인해 엔진오일이 EGR 밸브 내부 다이어프램 손상으로 인해 오일이 흡기로 유입되어 연소실로 들어가 불완전 연소함으로써 배기할 때 매연이 발생된 것으로 확인되었다. 두 번째 사례의 원인은 공기제어 장치인 스로틀 플랩(throttle flap)을 점검하였을 때 스로틀 플랩이 고착되어 흡입공기량 부족에 의해 매연이 발생된 것을 확인하였다. 세 번째 사례는, 배기가스 온도센서의 불량으로 인해 온도를 감지하지 못해 재생기능이 되지 않아 매연이 발생된 것으로 확인되었다. 따라서, 배기가스발생으로 인한 환경오염 문제가 발생하지 않도록 최적의 상태를 유지하도록 관리하여야 한다.

• 한국ITS학회 논문지
• /
• 제7권6호
• /
• pp.48-56
• /
• 2008

본 논문은 대기오염의 주범인 자동차 배기 가스량을 체크하고 차량내의 고장 유 무 진단 시스템 개발이다. 시스템 엔진 정보 추출을 위해 차량 CAN 통신을 이용하고 정보 전송을 위해 ZigBee를 통해 데이터 전송을 한다. 차량 CAN을 위해 차량에서 자체 제공되는 OBD-II 프로토콜을 사용하여 차량의 각종 센서 정보 및 O2 센서 값을 통해 차량 상태 정보 및 배기 가스양을 계산한다. 주행 중인 자동차 엔진 및 내부 고장에 잘 알지 못하는 일반 사용자를 위해 운행 중 실시간 차량의 자가진단 시스템 구축을 목적으로 하고 고장진단 프로토콜 전송을 위한 무선통신 인터페이스로 저 전력 저비용 ZigBee 통신 인터페이스를 구축한다. 자동차 그리고 진단 시스템의 통신을 위해 ZigBee 시스템을 통하여 효율적 저비용 통신 인터페이스를 구성하여 차량내의 엔진 및 각종 센서 정보 네트워크를 지원한다. 차량에서 전송되어 온 각종 센서정보는 ZigBee 기반을 통해 ZigBee 메인 컨트를 시스템에 전송된다. 차량에 이상이 생겼을 때 트러블 코드를 저장하고 자동차가 정비소에 갔을 때 정확한 판단을 하여 신속하게 처리 할 수 있게 해 주며 자동차에 대해서 잘 알지 못하는 운전자에게 정확한 정보를 제공한다. 또한 멀티미디어 시스템 기능을 추가하고 주행 중 무선 인터넷이 가능하도록 시스템을 확장한다. 마지막으로 주행 중 차량 자가진단을 위해 저 전력 임베디드 리눅스 시스템을 구축하고 실 실험을 통하여 구현하고 검증한다.

• 한국재료학회지
• /
• 제18권4호
• /
• pp.193-198
• /
• 2008

$WO_3$-doped $SnO_2$ thin films were prepared in a solution-deposition method and their gas-sensing characteristics were investigated. The doping of $WO_3$ to $SnO_2$ increased the response ($R_a/R_g,\;R_a$: resistance in air, $R_g$: resistance in gas) to $H_2$ substantially. Moreover, the $R_a/R_g$ value of 10 ppm CO increased to 5.65, whereas that of $NO_2$ did not change by a significant amount. The enhanced response to $H_2$ and the selective detection of CO in the presence of $NO_2$ were explained in relation to the change in the surface reaction by the addition of $WO_3$. The $WO_3$-doped $SnO_2$ sensor can be used with the application of a $H_2$ sensor for vehicles that utilize fuel cells and as an air quality sensor to detect CO-containing exhaust gases emitted from gasoline engines.

• 패션비즈니스
• /
• 제22권5호
• /
• pp.125-136
• /
• 2018

This study intended to develop a motorcycle safe vest that can be prepared against accidents by mounting a smart module (with built-in sensor) on the safe vest in order to emphasize safety among functional aspects of the motorcycle clothing. The research method investigated professional books, prior research, and Internet data to examine the characteristics of motorcycle wear and the theoretical examination of smart wear, and analyzed the functional characteristics of the design by reviewing smart jacket and vest design cases for motorcycles currently on the market. As a results of study an interface device sensor, which contains a sensor with IMU(Intertial Measurement Unit) and CPU(Central Processing Unit), was inserted into a motorcycle top in order to draw attention to the safety of motorcycle riders. The IMU sensor attached to the vest detected the tilting motion of the rider to either left or right side to obtain data on left or right direction, sudden stop, and so forth and displayed left or right turn signal and sudden stop sign on the backplate (back) through the LED module. As for charging the device to operate LEDs, a generator, which is designed to convert the heat energy in the exhaust into electric energy, was used to efficiently self-produce the power required to operate LEDs of the top while riding.