• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.94-99
• /
• 2000

When operating NC lathe, gear box which is equipped with gear train and spindle sometimes generates loud noise and excessive vibrations. In order to identify their causes, In this study, torsional and lateral vibration characteristics including critical speeds of the gear train-spindle system are first analyzed by using torsional and lateral vibration models of the gear train and shafts. Natural frequencies and modes of the gear box structure are also analyzed by impulse hammer test. Furthermore, measured vibration and noise signals are analyzed and compared with theoretical analysis results. At last it is concluded that the cause of the excessive mise and vibration is the resonance between gear meshing frequency including its side bands, shaft bending and torsional vibration frequencies, and the natural frequencies of th gear box structure. Consequently the noise and vibration levels are greatly reduced by avoiding resonance between them through the redesign of the gear module.

• 한국소음진동공학회논문집
• /
• 제22권2호
• /
• pp.156-162
• /
• 2012

This paper presents differences of road traffic noise maps were generated by using the draft map and two digital maps with different versions. As a first step, the calculation of the areas of excessive noise exposure was made for the draft map and each digital map version. Subsequently, the areas of excessive noise exposure were compared so as to determine how different from each other. Then, comparison of the populations exposed to excessive noise was also conducted in the same way. It was found that the most accurate noise map was obtained when using the combination of the draft map containing all attribute information and the digital map Ver 2.0. This result indicates that more information on the height and the number of floors of the individual building is required in order to obtain more accurate population exposed to excessive noise, thus creating a more accurate noise map.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2017년도 특별논문집
• /
• pp.14-18
• /
• 2017

The Lashing bridge and radar mast of ship are upright structures so they are generally exposed to excessive vibration. Recently, the use of low speed main engines for improving fuel efficiency has been increasing, and the excitation frequencies of the main engine are moving to the low frequency band. If the excitation frequencies are coincident with the natural frequencies of the local structure, excessive vibration occurs during main engine operating condition. The modal test is to experimentally determine resonance frequency, mode shape, and damping, which are vibration characteristics of a mechanical structure under dynamic external force. Through this study, the vibration characteristics of the structure are obtained by modal tests and the low vibration measure is applied to the local structures.

• 동력기계공학회지
• /
• 제5권3호
• /
• pp.64-72
• /
• 2001

This paper describes an optimal design technology in a segment type vertical guide bearing for vertical rotating machinery. Segment type vertical guide bearings have widely used for vertical rotating machinery, however bearing problems, such as excessive vibration and temperature rise, frequently take place in the actual machine. Such excessive vibration magnitude and/or abnormal bearing metal temperature rise result in serious damage and economic losses. Thus the segment type vertical guide bearing should be designed to get optimal characteristics in order to maintain stable operation without bearing failure due to abnormal vibration and/or abnormal bearing metal temperature. The preload ratio is the most important parameter in designing the segment type vertical guide bearing. Because adjustment of the bearing preload by changing the bearing clearance could easily control both the bearing stiffness and the cooling effect. In the paper, the influence of the preload effects on the bearing metal temperature and the bearing stiffness has been investigated both theoretically and experimentally in order to find out an optimum preload ratio. Results show that the segment type vertical guide bearing has an optimum preload ratio at which the bearing stiffness reaches a masimum value while the bearing metal temperature is minimized.

• Earthquakes and Structures
• /
• 제10권6호
• /
• pp.1451-1465
• /
• 2016

The effectiveness of base isolation (BI) systems for mitigation of seismic vibration of bridges have been extensively studied in the past. It is well established in those studies that the performance of BI system is largely dependent on the characteristics of isolator yield strength. For optimum design of such systems, normally a standard nonlinear optimization problem is formulated to minimize the maximum response of the structure, referred as Stochastic Structural Optimization (SSO). The SSO of BI system is usually performed with reference to a problem of unconstrained optimization without imposing any restriction on the maximum isolator displacement. In this regard it is important to note that the isolator displacement should not be arbitrarily large to fulfil the serviceability requirements and to avoid the possibility of pounding to the adjacent units. The present study is intended to incorporate the effect of excessive isolator displacement in optimizing BI system to control seismic vibration effect of bridges. In doing so, the necessary stochastic response of the isolated bridge needs to be optimized is obtained in the framework of statistical linearization of the related nonlinear random vibration problem. A simply supported bridge is taken up to elucidate the effect of constraint condition on optimum design and overall performance of the isolated bridge compared to that of obtained by the conventional unconstrained optimization approach.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2005년도 특별논문집
• /
• pp.216-221
• /
• 2005

Many tanks such as a fresh water tank, an aft peak tank and oil tanks are arranged in the engine room and aft part areas of the ship. By added mass effect of the fluid inside the tanks, the natural frequency will be changed according to filling height of the tank. For this reason, there is possibility of occurrence of excessive vibration by resonance between natural frequencies of local structure and excitation frequencies of the propeller or main engine. Therefore, calculation of natural frequencies is required for structure for many types of tank which are contacting with water or oil to consider added mass effect for anti-resonance design at design stage. In this study, a case of structure damage on the fresh water tank for 2600 TEU container vessel is introduced. In addition, natural frequency analysis and vibration measurement have been performed to investigate vibration characteristics for excessive vibration control.

• 소음진동
• /
• 제5권1호
• /
• pp.67-73
• /
• 1995

In earth moving construction equipment used for rough and dangerous works, seat suspension system is the only means for reducing the vibration transmitted to the operator. Thus ISO(International Organization for Standardization) 7096 suggests a recommendation for the vibration characteristics of the seat suspension system in order to protect the human beings from excessive vibrationl. In this research, a new mechanical type seat suspension system is designed and a mathematical model, effective design parameters of the seat suspension system are determined and concept design strategy is presented.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 가을 학술발표회 논문집
• /
• pp.362-369
• /
• 2002

This paper mainly propose the new passive vibration control device, named BRV(the bridge reduced vibration), for reducing excessive traffic-induced vibration of bridges and for measuring performance of BRV numerical example was simulated. The purpose of BRV is mainly on reducing vertical acceleration and displacement of bridge. In BRV we can control the stiffness and damping coefficient to accept the performance we want. The result of simulation showed that the vertical acceleration and displacement was effectively diminished. It would be concluded that BRV can be used to improve the serviceability of bridge and fatigue life etc.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.706-711
• /
• 2001

A dynamic vibration absorber(DVA) is developed to reduce the excessive focusing vibration of an optical disc drive(ODD) originated from the resonance of an wobble disc. We design the material properties of the DVA by FEM model such as Young's modules, damping coefficient, shapes and dimensions, analyze its dynamic characteristics and provide its design guide line for suppressing the vibration of an optical disc drive. To examine the performance. of the DVA, the vibration of the wobble disc and the feeding system is measured by using a laser vibrometer and the noise level is checked by using microphone. The result shows that the proposed DVA reduces the vibration and. the noise in an optical disc drive.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.688-694
• /
• 2001

The 84m discharge line of moisture separator reheater(MSR) in Kori-2 had been suffered by excessive vibration from the beginning of power generation. In 1993, a complementary measure was taken to reduce the vibration level by adding several supports in the MSR pipeline. However, the piping vibration was beyond the allowable limit and an appropriate countermeasure was required to prevent the fatigue failure of the pipeline from the abnormal vibration. In this study, the vibrational characteristics of MSR pipeline and the countermeasure for abnormal vibration was investigated. Among the several vibration reduction methods, piping layout change by smoothing the pipeline was applied to the MSR pipeline in Kori-2. Applying the countermeasure, the vibration level was found to dramatically reduce from 17cm/sec to l.0cm/sec at the full-power operation condition.