• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2011년도 춘계학술대회 및 Fine pattern PCB 표면 처리 기술 워크샵
• /
• pp.205-206
• /
• 2011

Cu thin films for electromagnetic wave shielding were prepared on PET film and Ni-coated PET film by using Dry and Wet coating method, such as evaporation method, DC sputtering method and copper sulfate($CuSO_4$). After that, Zn thin film and Ni thin film were prepared onto the Cu thin films by using evaporation dry process and Ni electro plating wet process as a finishing treatment, respectively. The result of conductivity test and corrosion resistance test revealed Cu thin films which were formed with bigger grain size and high Cu composition rate have superior properties. Zn thin film by dry evaporation process and Ni thin film by wet electro plating process on Cu thin films were largely contributed to corrosion resistance. However, Ni thin film by wet process made conductivity of all specimen worse, the other hand, Zn thin film by dry process made it better to improve condictivity of specimens just prepared by dry process.

• 한국표면공학회지
• /
• 제54권3호
• /
• pp.133-138
• /
• 2021

Ternary Ti-X-N coatings, where X = Al, Si, Cr, O, etc., have been widely used for machining tools and cutting tools such as inserts, end-mills, and etc. Ti-Al-N-O coatings were deposited onto silicon wafer and WC-Co substrates by a cathodic arc evaporation (CAE) technique at various negative substrate bias voltages. In this study, the influence of substrate bias voltages during deposition on the microstructure and mechanical properties of Ti-Al-N-O coatings were systematically investigated to optimize the CAE deposition condition. Based on results from various analyses, the Ti-Al-N-O coatings prepared at substrate bias voltage of -80 V in the process exhibited excellent mechanical properties with a higher compressive residual stress. The Ti-Al-N-O (-80 V) coating exhibited the highest hardness around 30 GPa and elastic modulus around 303 GPa. The improvement of mechanical properties with optimized bias voltage of -80 V can be explained with the diminution of macroparticles, film densification and residual stress induced by ion bombardment effect. However, the increasing bias voltage above -80 V caused reduction in film deposition rate in the Ti-Al-N-O coatings due to re-sputtering and ion bombardment phenomenon.

• Tribology and Lubricants
• /
• 제8권1호
• /
• pp.63-69
• /
• 1992

In order to gain better understanding of wear behaviors of TiN-coated boron cast iron, tests and analyses were conducted with block-on disc type tribometer. TiN layer of thickness $2 \mu m$ and $4 \mu m$, coated by cathodic arc evaporation process, were experimentally investigated with the variation of applied load and sliding speed under dry sliding condition. Wear characteristics were expressed in terms of the three-dimentional wear map as well as the wear rate vs sliding speed and load. Comparisons of wear and friction characteristics between coated cast irons and uncoated cast irns were also made. Wear mechanism of TiN layer was explained in view of surface interaction between the mating surfaces. The thicker coating exhibited higher hardness and adhesion strength. the significance of stresses at the surface and in the subsurface was briefly discussed in relation to the wear behavior.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.618-620
• /
• 1997

A $50{\times}50{\mu}m^2$ aluminum micromirror array is fabricated using shadow evaporation process. The fabrication process is very simple with use of shadow evaporation process, and the micromirror array has a high fill-factor. The static and dynamic characteristics such as deflection angle vs. applied voltage, step response, and frequency response are measured using a contact free optical measurement technique. The downward threshold voltage was 8 V, step response time was $13.5{\mu}s$ when 32 V step voltage applied, and a resonance observed at 11kHz. The lifetime of micromirror with anti-stiction coating was tested and micromirror operated successfully over 200 million cycles of touch-down operations.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 춘계학술대회 논문집 디스플레이 광소자 분야
• /
• pp.169-172
• /
• 2005

공정시 플라스틱 기판의 변형을 방지하기 위해 PC(Polycarbonate) 기판을 약 12시간 동안 pre-annealing시킨 다음 SiN(silicon nitride)와 PI(Poly-imide)를 각각 Sputter와 Spin-Coater를 이용하여 Coating하였다. 완성된 PC 기판위에 Themal Evaporation으로 Calsium을 증착한 뒤 Al을 올렸다. Calsium 증착 된면에 삼성 코닝의 글래스를 UV resin으로 부착 시킨 다음 상온에서 투습률을 측정하였다. 측정 간격은 12시간으로 하였으며 Calsium Test 의 정확도 향상을 위해 CCD Camera로 측정하여 컴퓨터로 분석하였다. 그래픽 저장 파일은 저장시 이미지 손실을 방지하기 위해 Bitmap방식을 그대로 사용 하였으며 정확도 향상을 위한 분석 프로그램은 MicroSoft 사의 Visual C++로 작성하였다. 화상 처리 면적은 컴퓨터 시스템의 처리 속도를 감안하여 70*70 으로 하였다.

• 보존과학연구
• /
• 통권29호
• /
• pp.65-90
• /
• 2008

This study examines the status and the physical features of Paraloid B-72 layers with examination of microstructure and analysis of organic matters. Paraloid B-72 layers were coated on samples from the colour layer of outer wall painting in Mireuk hall in Geumsan temple. On the basis of the previous examination result, it has made the samples which are similar to outer wall in Mireuk hall in Geumsan temple. The samples can be divided into two, one; 5% Paraloid B-72 coating and another is without coating. Then samples have been experimented under the compulsive environments of infrared radiation and immersion, thereafter compared the results of the damages and physical features between two samples. As a result of the comparison, the sample with Paraloid B-72 had more serious cracks, exfoliations and peeling layers than that of without Paraloid B-72. Otherwise, in the examination of ultraviolet radiation, the sample with Paraloid B-72 coating showed weaker physical properties, less density in structure of colour layer and less hardness in surface of colour layer than the sample without coating. The percentage of moisture content after the ultraviolet radiation was higher in the sample without Paraloid B-72 than the sample with Paraloid B-72 coating. Observing the conditions before the ultraviolet radiation, the sample with Paraloid B-72 coating demonstrated lower rate in moisture evaporation rate than the sample without Paraloid B-72. As a consequence, in examination of this samples, the change of physical features are increased in the sample with Paraloid B-72 coating than that without Paraloid B-72 when compulsive environment of heat, moisture and ultraviolet rays for a short term are imposed.

• 전자공학회논문지
• /
• 제52권5호
• /
• pp.206-213
• /
• 2015

함정용 전자광학추적장비의 센서부에서 해수면반사파에 의해 발생하게 되는 영상추적간섭 현상을 최소화하고자 전방향성, 점진적인 굴절률 및 표면 요철구조를 갖는 산화아연에 플루오르화마그네슘을 코팅한 반사방지막을 전자빔 증착 장비를 통해 제작하였다. 최적화된 산화아연에 플루오르화마그네슘을 코팅한 반사방지막은 기존의 산화아연 반사방지막과 비교하여 점진적인 굴절률 변화에 따라 표면 프레넬 반사를 최소화하고 이를 통해 전자광학추적장비의 영상추적간섭 현상을 제거하는 장점이 있다. 본 실험을 통해, 산화아연에 플루오르화마그네슘을 코팅한 반사방지막이 다양한 전자광학장비의 반사방지막으로써 적용이 가능함을 확인하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.101-104
• /
• 1998

A new planar-type micro gas sensor was designed and fabricated on silicon substrate and the operating characteristics of the sensor were investigated. The thin sensitive film of the sensor was fabricated by spin-coating of the SnO$_2$ sol solution which was synthesized by hydrothermal method. The spin-coating method for preparation of sensing layer was adopted to improve the long-term stability of the fabricated sensing film instead of physical methods such as rf sputtering and thermal evaporation. The fabricated microsensor showed a fairly good sensing performance for CO gas in air at 250$^{\circ}C$ The sensitivity(S=Ra/Rg) was shown to be about 5 to 2000ppm CO with heating power of 50mW.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.984-987
• /
• 2002

In this study, It is to synthesize PPV-copolymer and to make polymer electroluminesence device in single layer of ITO/PPV -copolymer/metal. and then it has been realized basic characteristics for display device through analysis and recognized application possibility by luminous material. PPV-copolymer is used spin coating method and electrode is evaporated of vacuum deposition method by changing materials. The result of experiment, The PPV-copolymer used this study emitted blue color, could be discovered a change of emttion characteristic by electrode material.

• Transactions on Electrical and Electronic Materials
• /
• 제4권3호
• /
• pp.15-18
• /
• 2003

Aluminum oxide ($Al_2O_3$) materials were coated conformally on ZnO nanorods by atomic layer deposition (ALD). The ZnO nanorods were first synthesized on a Si(100) substrate from ball-milled ZnO powders by a thermal evaporation procedure. $Al_2O_3$ films were then deposited on these ZnO nanorods by ALD at a substrate temperature of $300^{\circ}C$ using trimethylaluminum (TMA) and distilled water ($H_2O$). Transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM) images of the deposited ZnO nanorods revealed that amorphous $Al_2O_3$ cylindrical shells surround the ZnO nanorods. These TEM images illustrate that ALD has an excellent capability to coat any shape of nanorods conformally.