• Journal of Auto-vehicle Safety Association
• /
• v.6 no.2
• /
• pp.72-77
• /
• 2014

In the ongoing debates over the need to identify new sources of energy and to reduce the emissions of greenhouse gases. Hydrogen has emerged as one of the most promising alternatives due to its emissions from the vehicle being virtually zero. The governments have identified the development of regulations and standards as one of the key requirements for commercialization of hydrogen-fueled vehicles. Regulations and standards will helpful in overcoming technological barriers to commercialization. Developments of a technique for safety assessment of Hydrogen Fuel Cell Vehicle(HFCV) includes four tasks, research for regulation system and policy, hydrogen safety, vehicle operation safety and protection against high-voltage. The objective is to establish a technique for safety assessment and amend safety standards for HFCV and consequently reflect research results to vehicle management policy. We devised safety standards and evaluation techniques with regard to high-pressure gas and high voltage of hydrogen fuel cell vehicle. Korean Motor Vehicle Safety Standards(KMVSS) for HFCV was amended to June 10, 2014. including the results of the safety assessment technology for high-voltage and hydrogen characteristics.

• Journal of Korean Critical Care Nursing
• /
• v.2 no.1
• /
• pp.36-47
• /
• 2009

Purpose: This study was to determine ICU nurses noncompliance of critical care nursing standards in order to provide basic data for education aimed at improvement in practice and evaluation of quality of nursing care in ICU. Methods: Data was collected from 150 nurses who work for three educational hospitals which have more than 800 beds and located in Gyeonggi province using questionnaires from September 2007 to October 2007. Results: The highest categories of noncompliance of critical care nursing standards were admission care($2.71\pm.60$) and infection control($2.31\pm.70$). The main causes of noncompliance critical care nursing standards that nurses regarded as causes were lack of attention(80.7%). ICU nurses mainly reported their noncompliance to charge nurses(89.3%) within 30minutes (84.7%). The reasons they reported were to solve problems rapidly and correctly, to reduce a harm to patients, and to prevent making noncompliance again. The reasons they didn't report were that they thought it might be not a problem and there was no change of patients conditions. Conclusion: ICU nurses noncompliance of critical care nursing standards was determined, therefore it can be used for prevention of further noncompliance.

• Journal of Families and Better Life
• /
• v.31 no.6
• /
• pp.39-51
• /
• 2013

Because of the increasing demand for day care centers, The Korean government has enforced childcare accreditation. The government has created the evaluation certification system for child care facilities. But the system includes variable items, and the physical rules are not sufficient for ensuring security and quality amenities. So this study, through literature search, examined the rules of Child Care Centers in the U.S. and compared them with those in Korea focusing on the provision of security and amenities. The standards found in 4 U.S. states were investigated, and the results are as follows. The rule pertaining to the size of indoor activity spaces in C.C.C. allows the spaces to be smaller in Korea than in the U.S. There is no specific criterion for infants and toddlers in our standard. When comparing the standards of Korea with those of the United States, Korea's standards do not state specific rules about child care facilities such as indoor furniture, finishes and space planning. Additionally, the binding force ensuring compliance with the standards of physical facilities is weak. Thus, the ratings of child care standards for the physical environment should be presented in detail. And if a center does not comply with the criteria, stronger penalties will have to be imposed.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.46 no.1
• /
• pp.99-105
• /
• 2004

The present agricultural water quality standards are set by a policy goal. This is intended for water quality management of public water resources, but not for the use of water resources. These standards were not determined by considering the influence of water quality on the safety of agricultural produce and the growth, yield and quality of agricultural crops. Thus, this study was carried out to investigate the influence of irrigation water quality on the growth, yield, and grain quality of rice and acquire fundamental knowledges to set up irrigation water quality standards. The pot experiment was conducted with 4 treatments using irrigation waters with various total nitrogen concentrations (control, 1, 5, 10, 20mg/L) and replicated four times with randomized block design. The results of this study showed that plant height, number of tiller, plant dry weight, the uptake of N, P, and K, and rice protein contents tended to increase as the T-N concentration in irrigation water was increased. In addition, grain yield at T-N 20 mg/L was significantly higher than in the control, but the percentage of head rice was slightly lower due to the increase of green kernel and white belly/core kernel.

• Journal of the Korean Society of Safety
• /
• v.23 no.5
• /
• pp.30-34
• /
• 2008

To evaluate the mechanical properties of in-service materials, tensile properties measurement using small-scaled specimen has been carried out. Tensile testing specimens with various dimensions, including standard and sub-size specimen specified in ASTM and ISO and small-scaled specimen, were prepared. Tensile strain in small-scaled specimen was measured using micro-ESPI system set up in this study. This system was used in the specimen with the parallel length of 2 mm and in subsequently measuring the strain under tensile loading. From each type of tensile specimen, stress-strain curves were determined. The dimension effect of the tensile properties was investigated comparing the tensile results obtained from standard specimens and small-scaled specimens. It was shown that the tensile strength for the small-scaled specimen is lower by 15% than those for the standard specimen.

• Journal of Biomedical Engineering Research
• /
• v.43 no.3
• /
• pp.147-152
• /
• 2022

This research is to measure real-time temperature distribution inside a tissue-mimicking phantom for the safety and effectiveness evaluations of focused ultrasound (FUS) device capable of linear scanning stimulation. Since the focusing area of the FUS stimulation device is smaller than diameter of conventional thermal probe and keeps moving, it is impossible to monitor temperature distribution inside the phantom. By using the phantom with a thin film temperature sensor array inserted, real-time temperature change caused by the FUS device was measured. The translation of the measured temperature peak was also tracked successfully. The present phantom had been experimentally proven to be applicable to validate the performance and safety of the therapeutic ultrasound devices.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.60 no.2
• /
• pp.179-185
• /
• 2024

The model ship of this study, the Baek-Kyung fisheries training ship of Pukyong National University, has a length between perpendiculars of 85 meters, making it not subject to the IMO maneuverability standards. However, understanding the maneuvering characteristics of the vessel is essential for safe navigation. In this regard, this study was conducted to analyze the results from the sea trials of the model ship conducted in accordance with the IMO maneuverability standards. The results of the turning tests met the standards well while in the zig-zag tests, the first overshoot angle exceeded the standard in the 10°/10° test; however, such results met with a difference of 1.8° in the 20°/20° test. Additionally, using the course-stability discrimination formula, the calculated value was -0.0051, indicating unstable course-stability. The results of the stopping tests met the standards well. It is hoped that the analyzed maneuvering characteristics of the model ship from the study results will contribute to the safety of ship navigation.

• International Commerce and Information Review
• /
• v.13 no.1
• /
• pp.179-196
• /
• 2011

This study aims to measure the relative importance of trade insurance using AHP developed by Thomas Saaty of Pennsylvania in early 1970s. Moreover, it provides help in the development of a comprehensive strategy of trade insurance. To obtain priority of trade insurance in its functions, this study discovered significance and relative importance of two evaluation standards and four individual evaluation items. Of the two evaluation standards, importance of credit exposure was 63%. It was discovered that it was more important than political means (37%). Of the four individual evaluation items, importance of banking supplementation was 60%. It was more important than credit investigation of overseas traders (40%). Importance of trade promotion policy was 69%, which was more important than removal of anxiety in trade (31%). As a result of comparing priorities of the f tire evaluation items, priority of banking supplementation was 38% followed by trade promotion policy means (26%), credit investigation of overseas traders (25%) and removal of anxiety in trade (12%).

• Journal of Biomedical Engineering Research
• /
• v.41 no.6
• /
• pp.256-263
• /
• 2020

The importance of quality control has been emphasized to maintain safety of patients and satisfaction of medical service with medical devices used in clinic. Accordingly, objective evaluation method and standards consistently has been brought up for demand to replace outdated medical devices in appropriate time and to maintain the quality of medical service. Though many studies made suggestions methods to determine what medical devices to be replaced first, these methods were difficult in practice for its complex evaluation criteria and long time to evaluate. Therefore, in this study, a simple evaluation method is developed to identify and prioritize medical devices that are ought to be replaced. For the development of this simple evaluation method, four major characteristics of technology, safety, finance, and user satisfaction, which are considered in clinics to evaluate medical device replacement, and 14 minor attributes are distinctively selected. Each characteristic is assessed in binary form of "YES" or "NO" to minimize its subjective nature. Using this method to evaluate sampled medical devices belonging to four different characteristics, devices are suggested to be replaced in the current financial year or in the following financial year, or re-evaluated by the end of this financial year. Such results of evaluation can amend the subjective nature of existing evaluation method and give objective standards more promptly.

• Journal of radiological science and technology
• /
• v.45 no.2
• /
• pp.127-134
• /
• 2022

In order to overcome the image quality limitations of the conventional C-arm, a flat panel detector (FPD) is used to enhance spatial resolution, detective quantum efficiency, frame rate, and dynamic range. Three-dimensional (3D) visualized information can be obtained from C-arm computed tomography (CT) equipped with an FPD, which can reduce patient discomfort and provide various medical information to health care providers by conducting procedures in the interventional procedure room without moving the patient to the CT scan room. Unlike a conventional C-arm device, a C-arm CT requires different basic safety and essential performance evaluation criteria; therefore, in this study, basic safety and essential performance evaluation criteria to protect patients, medical staff, and radiologists were derived based on International Electrotechnical Commission (IEC) standards, the Ministry of Food and Drug Safety (MFDS) standards in Korea, and the rules on the installation and operation of special medical equipment in Korea. As a result of the study, six basic safety evaluation criteria related to electrical and mechanical radiation safety (leakage current, collision protection, emergency stopping device, overheating, recovery management, and ingress of water or particulate matter into medical electrical (ME) equipment and ME systems: footswitches) and 14 essential performance evaluation criteria (accuracy of tube voltage, accuracy of tube current, accuracy of loading time, accuracy of current time product, reproducibility of radiation output, linearity and consistency in radiography, half layer value in X-ray equipment, focal size and collimator, relationship between X-ray field and image reception area, consistency of light irradiation versus X-ray irradiation, performance of the mechanical device, focal spot to skin distance accuracy, image quality evaluation, and technical characteristic of cone-beam computed tomography) were selected for a total of 20 criteria.