• Korea-Australia Rheology Journal
• /
• 제18권2호
• /
• pp.109-118
• /
• 2006

A finite-element method was employed to analyze axisymmetric unsteady motion of a deformable bubble near the wall. In the present study a deformable bubble in a Newtonian medium near the wall was considered. In solving the governing equations a structured mesh generator was used to describe the collapse of highly deformed bubbles with the Arbitrary Lagrangian Eulerian (ALE) method being employed in order to capture the transient bubble boundary effectively. In order to check the accuracy of the present FE analysis we compared the results of our FE solutions with the result of the collapse of spherical bubbles in a large body of fluid in which solutions can be obtained using a 1D FE analysis. It has been found that 1D and 2D bubble deformations are in good agreement for spherically symmetric problems confirming the validity of the numerical code. Non-spherically symmetric problems were also solved for the collapse of bubble located near a plane solid wall. We have shown that a microjet develops at the bubble boundary away from the wall as already observed experimentally. We have discussed the effect of Reynolds number and distance of the bubble center from the wall on the transient collapse pattern of bubble.

• 대한토목학회논문집
• /
• 제9권3호
• /
• pp.65-73
• /
• 1989

응력파의 영향을 받는 균열의 동적응력확대계수를 구하기 위해 동적에너지방출율에 관한 명시적인 표현식을 유도하고, 이를 이용하여 유한요소법에 적합한 수치계산방법을 제시한다. 새로운 운동학적 기술방법과 균열의 가상증분을 이용하여 균열선단의 유한한 영역에서 정의되는 체적적분식을 연속체 역학적인 정식화를 통하여 구하고, 이의 수치적분 유한영역의 모델링에 사용된 등매개변수특이요소 내에서 특이성을 만족하는 적합조건하에서 수행된다. 본 방법은 경로적분식을 이용하는 기존 방법들에 비해 보다 정확하고 안정된 결과를 제공하고 동시에 응력파의 영향을 적시에 조사할 수 있으며, 본 방법에 의해 개발된 유한요소모듈은 기존의 동적응력 해석프로그램에 용이하게 연결 설치할 수 있음을 보인다.

• 한국정밀공학회지
• /
• 제29권6호
• /
• pp.632-639
• /
• 2012

A fully coupled thermo-mechanical model is adopted to study the temperature distribution and the material deformation in friction stir welding(FSW) process. Rotational speed is most important parameters in this research. Three dimension results under different process parameters were presented. Result indicate that the maximum temperature is lower than the melting point of the welding material. The higher temperature gradient occurs in the leading side of the workpiece. The maximum temperature can be increased with increasing the tool angular velocity, rpm in the current numerical modeling. In this research ABAQUS Ver.6.7 is to analyze a fully coupled thermo-mechanical model. ALE(Arbitrary Lagrangian-Eulerian) finite element formulation is used for the large deformation in FSW process and using the Mass scaling for the analysis time efficiency.

• 대한기계학회논문집A
• /
• 제36권9호
• /
• pp.1073-1080
• /
• 2012

점진성형은 공구 운동으로 소재의 국부 소성변형 영역을 전체 소재에 확장시켜 목표 형상으로 변형시키는 냉간 성형공정이다. 본 논문에서는 점진성형의 유한요소해석 시 묘사기법에 관한 연구를 수행하였다. 고찰할 묘사기법으로 라그랑지언 묘사법과 ALE 묘사법을 선택하였다. 미끄럼 경계기법도 공구와 접촉표면에서 요소의 찌그러짐을 극복하기 위한 방법중의 한가지 경우로 고찰하였다. 묘사기법과 경계기법의 다양한 조합 중에 ALE 묘사법과 연계한 미끄럼 경계기법의 경우가 요소의 찌그러짐을 가장 완화 시켰다. 이 방법이 최종 단계 변형까지 점진성형 해석을 지속할 수 있도록 해주는 유일한 조합인 것으로 나타났다. 이에 반해, 라그랑지언 묘사법 및 순수 ALE 묘사법은 점진성형 해석 중에 요소의 찌그러짐이 극심하여 최종 변형 형상에 도달하기 오래 전에 해석이 중단되는 상태를 보였다.

• 한국해양공학회지
• /
• 제32권3호
• /
• pp.177-183
• /
• 2018

This study simulated ice load and the motion response of a moored semi-submersible rig in pack-ice conditions using a finite element method. Ice flows of random size and shape were modeled, and interactions for ice-sea, ice-structure, ice-ice were simulated using a simplified method. Parameters for the simplified method such as drag force coefficient and the pressure-penetration relation were obtained based on the result of detailed analysis using the coupled Eulerian-Lagrangian method. The mooring lines were modeled by spring elements based on their stiffness. As a result of the simulation over 1,400 seconds, the force and motion response of the rig were obtained and validated using discrete elements and compared with the results found by the Krylov State Research Centre.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제8권2호
• /
• pp.137-152
• /
• 2016

This paper studied the dynamic response of a new gasbag-type floating bridge under the effect of a moving load. The arbitrary Lagrangian-Eulerian (ALE) method was used to simulate the movement of seawater and air, and the penalty-based method was used to study the coupling between gasbags and fluid. A three-dimensional finite element model of the floating bridge was established, and the numerical model was verified by comparing with the experimental results. In order to prevent resonance, the natural frequencies and flexural mode shapes were analyzed. Based on the initial state analysis, the dynamic responses of the floating bridge subjected to different moving loads were investigated. Vertical displacements and radial deformations of gasbags under different loads were compared, and principal stress distributions of gasbags were researched while driving. The hinge forces between adjacent modules were calculated to ensure the connection strength. Besides, the floating bridge under wave impacting was analyzed. Those results can provide references for the analysis and design of this new floating bridge.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2007년도 정기 학술대회 논문집
• /
• pp.783-788
• /
• 2007

Many researches have been studied several vibration control device such as TMD and TLD to reduce the influence of wind or seismic waves for high-rise buildings. TLD provides some advantages such as easy installation and low maintenance cost. However, because of the difficulties in evaluating the characteristics of TLD, the dynamic characteristics of TLD must be investigated by experiment or analysis. In this study, the dynamic response analysis of structure with TLD was carried out to verify the vibration control ability of the proposed TLD for high-rise building. The parameter of interest was chosen by the height of the water level and the frequency of input seismic wave in the same shape of water tank.

• 반도체디스플레이기술학회지
• /
• 제9권3호
• /
• pp.29-34
• /
• 2010

Nanoimprint lithography (NIL) is an emerging technology enabling cost effective and high throughput nanofabrication. To successfully imprint a nanometer scale patterns, the understanding of the mechanism in nanoimprint forming is essential. In this paper, a numerical analysis of polymer flow in thermal NIL was performed. First, a finite element model of the periodic mold structure with prescribed boundary conditions was established. Then, the volume of fluid (VOF) and grid deformation method were utilized to calculate the free surfaces of the polymer flow based on an Eulerian grid system. From the simulation, the velocity fields and the imprinting pressure for constant imprinting velocity in thermal NIL were obtained. The velocity field is significant because it can directly describe the mode of the polymer deformation, which is the key role to determine the mechanism of nanoimprint forming. Effects of different mold shapes and various thicknesses of polymer resist were also investigated.

• 한국전산구조공학회논문집
• /
• 제36권6호
• /
• pp.355-364
• /
• 2023

폭발 수치해석 기법 중 Arbitrary Lagrangian-Eulerian(ALE)는 구조물의 파괴뿐만 아니라 폭발 이후 충격파의 전파 과정까지 관찰할 수 있는 장점이 있다. 그러나 동적 해석 시 유한요소 모델의 격자망 크기가 일정 수준 이하로 감소하게 되면 해석 결과의 신뢰도가 부정확해진다. 본 연구에서는 ALE 수치해석 기법을 활용하여 대기의 격자망 크기가 해석의 정확도에 미치는 영향을 조사한다. 다양한 조건의 격자망 크기와 폭발 중량을 갖는 대기 중 폭발모델을 구축하고, 폭발 중심으로부터 거리에 따른 폭발압력을 관찰한다. 수치해석과 실험에서 얻은 최대 폭발압력 결과에 대해 평균 제곱 오차를 계산하여 최적의 격자망 크기를 제안하고, 제안된 크기를 바탕으로 폭발물 중량과 대기의 최적 격자망 크기에 대한 상관관계를 분석한다. 본 연구는 다양한 중량을 가진 폭발물 해석에서 최적의 격자망 크기를 제공함으로써 신뢰성이 향상된 폭발 수치해석 모델 개발에 도움이 될 것으로 기대한다.

• Structural Engineering and Mechanics
• /
• 제13권6호
• /
• pp.653-670
• /
• 2002

In order to ensure the structural dynamic stability of moving liquid-storage containers, the flow motion of interior liquid should be appropriately suppressed by means of mechanical devices such as the disc-type elastic baffle. In practice, the design of a suitable baffle requires a priori the parametric dynamic characteristics of storage containers, with respect to the design parameters of baffle, such as the installation location and inner-hole size, the baffle number, and so on. In this paper, we intend to investigate the parametric effect of the baffle parameters on the transient dynamic behavior of a cylindrical fuel-storage tank in an abrupt vertical acceleration motion. For this goal, we employ the ALE (arbitrary Lagrangian-Eulerian) kinematic description method incorporated with the finite element method.