• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.9
• /
• pp.647-653
• /
• 2007

In dynamic ice storage system(DISS), ice slurry is formed not only from solution freezing by mechanical removing parts but also supercooled solution. However, in order to perform continuous ice formation in the system without mechanical moving parts, supercooled aqueous solution should be formed stable through cooling heat exchanger and be dissolved uniformly in storage tank. In previous study, the time of ice slurry increased as the pressure of the cooling heat exchanger(PHX) increased. In this study, a cooling experiment of an ethylene glycol 7mass% solution was performed with various inlet temperature of the PHX, which has constant brine inlet temperature of $-7^{\circ}C$. The temperature in the storage tank maintained to freezing point of the solution. At results, the time of ice slurry formation increased as the supercooling degree decreased and the cooling rate increased.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.651-655
• /
• 2004

This paper studies the designing method and application for grommets, rubber material used to absorb vibration on the air conditioner compressor. The existing grommet with hardness 40 degrees, EPDM, has the high transmissibility on the compressor that causes additional structure born sound. The problem for EPDM is transformation over long time usage possibly due to its design in which stress is concentrated on a certain position. In order to resolve it, silicon material was previously used with the same design in some models. The vibration performance did improve, but the cost became high. Below are the major developments regarding improvements in compressor rubber material, vibration performance and durability through design change, and new grommet to attain cost reduction. 1 The optimum grommet design for stress even distribution through FEM methods. 2. Comparison for grommet material and design for improved transmissibility. 3. Assess for grommets durability and product applications.

• Elastomers and Composites
• /
• v.43 no.1
• /
• pp.1-7
• /
• 2008

Far-infrared vulcanization of ethylene-propylene-diene terpolymer(EPDM) compounds has been studied in comparison with hot air vulcanization. Vulcanization characteristics of EPDM compounds were measured by degree of curing and temperature of specimens in vulcanization process. As a result, degree of curing by far-infrared of EPDM compounds was shown to be higher value than that by hot air at the same vulcanization temperature. Especially, degree of curing by far-infrared on 3 mm thickness of EPDM compounds was increased by two times compared to that by hot air. While the increase of thermal conductivity of EPDM compounds highly improved degree of curing by far-infrared, that hardly improved degree of curing by hot air.

• Journal of Animal Science and Technology
• /
• v.48 no.6
• /
• pp.797-804
• /
• 2006

The present study was undertaken to investigate the post-thawed survivability of bovine embryo depending on different dose of ethylene glycol and sucrose. Ovaries were collected at local slaughterhouse and the cumulus-oocyte-complexes aspirated from ovaries were in vitro matured, fertilized and cultured at 39°C in an atmosphere of 5% CO2 incubator. For conventional slow-freezing, d 7 or 8 expanded blastocysts were collected. Embryos were equilibrated in 1.5 M and 1.8 M ethylene glycol(EG) with 0.1 M and 0.3 M sucrose in Dulbecco's phosphate-buffered saline(D-PBS) supplemented with 0.5% bovine serum albumin. Embryos were then loaded individually into 0.25ml-straw and placed directly into cooling chamber of programmable freezer precooled to 󰠏7°C, after 2 min, the straw was seeded, maintained at 󰠏7°C for 8 min, and then cooled to 󰠏35°C at 0.3°C/min, plunged and stored in liquid nitrogen for at least 3 days. For thawing, the straw containing embryos were warmed in air for 10 sec and exposed to 37°C water for 20 sec. Straws were then removed from 37°C water. Rates of blastocyst survive and hatching were evaluated at 24 to 72 h post-warming. No difference of the survivability was shown between 1.5 M and 1.8 M EG (71 and 70%, respectively). Addition of 0.1 M sucrose to 1.5 M and 1.8 M ethylene glycol in the freezing solution did not differ significantly embryo survival (74 and 77%, respectively), whereas survival rates was higher(89%) in freezing solution contained 0.3M sucrose to 1.8M EG compared with 0.3M sucrose to 1.5M EG group(71%). However, there was no difference in the overall total cell number between the two groups (122±1.8 vs 131±1.4, respectively). In conclusion, the results suggest that 0.3 M sucrose in 1.8 M EG may be optimal condition for freezing and thawing methods with in vitro produced embryos and may be applied to on-farm conditions for embryo transfer.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.9
• /
• pp.1027-1031
• /
• 2014

Free cooling system is used to reduce energy consumption of cooling system. Free cooling system is consisted of cooling group and dry-cooler in which heat exchange of chilled water and out air is conducted. Although this system has an excellent energy saving effect in place having cooling load regularly, data or material of design for free cooling system is lacked. In this study, characteristics analysis of free cooling system is conducted through software HYSYS with changing some facts. The main result is following as : Dry-cooler capacity is influenced by out air temperature, required chilled water temperature and LMTD(Logarithmic Mean Temperature Difference) of heat exchanger. As out air temperature is more low, dry-cooler capacity become increased. in addition, as required chilled water temperature is more high and LMTD is more low, the out air temperature range is widened for using dry-cooler. If out air temperature is below $0^{\circ}C$, antifreeze need to be used because freeze and burst can be occurred. In case of South Korea, antifreeze of 34% of ethylene glycol concentration is proper. When compressor load of R22, R134a and R407C is compared, considering environmental regulation and energy consumption, R134a is best working fluid.

• Journal of Magnetics
• /
• v.2 no.1
• /
• pp.16-21
• /
• 1997

Those were investigated, the crystallographic, morphological, and magnetic properties of barium ferrite film (SiO2/Si substrate) prepared by sol-gel dip coating. Appropriate sol was prepared by dissolvin barium and iron nitrate in ethylene glycol at 80$^{\circ}C$. To obtain the films, thermally oxidized p-type silicon substrate with (111) of crystallographic orientation were dipped into the sol, dried at 250$^{\circ}C$ to remove organic material, and heated at 800$^{\circ}C$ for 3 hours in air for the crystallization of barium ferrite. It was found that the particles of barium ferrite formed on the substrate exhibited needle-like shape placing parallel to the substrate and its c-axis is long axis direction. There was tendency that the coercive force in horizontal direction to the substrate was higher than that in vertical direction to it. This tendency was profound in large thickness.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2154-2159
• /
• 2007

The potential of using a double-faced wall stagnation flow burner in mass production of carbon nanotubes was evaluated experimentally and computationally. With nitrogen-diluted premixed ethylene-air flames established on the Nickel-coated stainless steel double-faced wall, the propensities of carbon nanotube formation were experimentally determined using SEM and FE-TEM images and Raman spectroscopy, while the flame structure was computationally predicted using a 3-dimensional CFD code with a reduced reaction mechanism. The uniformity and yields of synthesized carbon nanotubes were evaluated in terms of the flame stretch rates. Results show substantial increase of area on the wall surface where uniform carbon nanotubes are synthesized with using the double-faced wall stagnation flow burner due to enhanced uniformity of temperature distribution along the wall surface and support the potential of using a double-faced wall stagnation flow burner in mass production of carbon nanotubes.

• Magazine of the Korea Concrete Institute
• /
• v.4 no.3
• /
• pp.157-166
• /
• 1992

해수환경하의 콘크리트 구조물은 동결융해의 반복에 의한 물리적인 침식과 해수중에 용존하는 각종의 이온들의 침투로 인한 화학적 침식에 의해 현저한 성능저하현상을 나타내는 것으로 알려져있다. 본 연구는 포졸란계 혼합재인 플라이 애쉬, 슬래그, 슬리카 흄과 폴리머계 혼합재인 Ethylene Vinyl Acetate(EVA), Styrene-Butadiene Rubber(SBR)를 사용하여 제조한 콘크리트 경화체의 해수환 경하에서 동결융해 저항성에 미치는 혼합재의 종류 및 첨가량의 영향, W/C의 영향을 비교 검토한 실험적 연구이다. 콘크리트의 동결융해 저항성을 위해서는 공기연행이 필수적이며, 공기연행시킨 경우 W/C가 낮을수록 동결융해 저항성이 우수하였다. 해수중에서의 동결융해 저항성은 슬래그분말을 첨가할 때 우수하였으며, 폴리머계 혼합재에서는 EVA가 우수한 결과를 나타내었다.

• Journal of Mechanical Science and Technology
• /
• v.14 no.6
• /
• pp.699-703
• /
• 2000

Experiments were carried out to investigate the characteristics of the hydrocarbon (HC) emissions and to reduce cold start hydrocarbons in gasoline engines. An HC adsorber was, used and it coated was by Pd/Rh catalyst with zeolite on a honeycomb monolith. The HCs were efficiently trapped at temperatures below $100^{\circ}C by physical adsorption. After adsorption, they were reduced gradually by the catalytic oxidation of Pd/Rh catalysts as the adsorber temperature increased above $100^{\circ}C. Increasing amounts of methane, ethylene and n-butane were emitted as the fuel-air mixture became richer and the engine speed decreased. As the temperature of adsorber increased, high-number carbons into low-number carbons. Thus, the C4 concentration decreased significantly during the first 30 seconds, and the C2 concentration increased continuously.

• Journal of Korean Society for Atmospheric Environment
• /
• v.14 no.2
• /
• pp.153-160
• /
• 1998

The concentrations of volatile organic compounds (VOCs) in the atmosphere were measured from the Yochon Industrial Estate and compared with those from Tongkwangyang and Seoul. The first important phenomenon observed in the air of Yochon was high concentrations of alkenes and in particular, ethylene and propene. For most dominant species, their means and standard deviations were high simultaneously. Concentrations of several major aliphatic species exhibited a similar pattern of diurnal variation, however, with different species combination on each day. Concentrations of several hazardous aromatic species also exhibited a similar pattern of diurnal variation on the same day, which was different from that observed in the diurnal variation of major aliphatic species. It was interpreted that some species were intermittently released from relevant processes. It was also understood that high concentrations and variations of VOC species in Yochon were localized and not related to high average concentrations of ozone in Yochon and Tongkwangyang areas.