• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.1
• /
• pp.35-42
• /
• 2012

This paper is about the implementation of low cost WiMAX remote radio head system with Ethernet instead of optical link. We deployed a simplified frame structure on the data frames transmitted between a basestation and remote radio heads in order to maximize Ethernet link utilization which shows relatively lower maximum throughput compared to that of optical links. In addition, a synchronization mechanism was applied on a basestation and remote radio heads placed on remote sites in order for simultaneous data transmission and reception in all remote radio heads which are essential for proper communication with terminals. These schemes are implemented with FPGA. The results of experiment with a WiMAX Femtocell show that our remote radio head systems efficiently deliver radio frames with proper timing.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.8
• /
• pp.1172-1179
• /
• 2010

In this paper, we analyze and design requirements of Network Function block and System Function block of MiTS network protocol based on Light-Weight Ethernet, also implement and test the protocol and library files. Light-Weight Ethernet Protocol consists of Network Function block and System Function block. NF receives and sends datagram based on UDP multi-casting communication. SF processes messages after distinguished Sentence and Binary Image Data.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.5
• /
• pp.1111-1116
• /
• 2005

The necessity of the home network have been enlarged gradually according to the distribution of ultra-high speed internet, the expansion of a digital information equipment and the change of a life pattern. In this paper, we proposed the embedded ethernet module that could be operate on eight bit system, but it could control home appliance with full ethernet speed. The embedded ethernet module consists of 8051 MCU and Hardware TCP/IP. In this module, we construct simple web server and port remote control program for I/O device control. We verified through internet that the developed embedded ethernet module could control and check home appliances anywhere and anytime. We expect the developed ethernet module can build up niche market at home network. And it will be helpful to activate home network market.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.780-783
• /
• 2009

The application of MOST150 technology has been required to satisfy the demand for the automotive infotainment system and the higher bandwidth requirements caused by the increase of the multimedia processing capacity. The Ethernet technology applied gateway was implemented for an efficient transmission of multimedia, a vehicle diagnosis, an external communication, a data processing between the MOST150 and the CAN communication method applied to many existing vehicles. The new algorithm and application were suggested in order to efficiently perform the data processing between other types of communication systems. The existing MOST150 frame is mainly composed of the Control Channel, the Legacy Packet Channel(async) and the Synchronous /Isochronous Channels and performs the data processing through these sequential channels. With the sense of this process, this study suggested the new algorithm that the Mapping method of the IETF's QoS Management was applied to the MOST150 technology for the efficient QoS.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.9
• /
• pp.1674-1680
• /
• 2009

This paper proposes an autonomous fault determination, fault zone isolation and fault restoration strategy based on the ethernet communication as a new attempt to solve the problem the of the existing central control method. In proposed method, The FRTU(Feeder Remote Terminal Unit)s on the feeder determines autonomously where the faulted zone is by exchanging the voltage and current information with neighbor FRTUs based on the network communication, and then separates the faulted zone in an nil-voltage status to make the protective device to reclose successively. In particular, the minimization of outage time and relational load balancing is archived by each interconnection switch which determines autonomously the load zone to be allocated among those zones after the sound outage zones was separated individually. Finally, to show effectiveness of the proposed fault restoration strategy, the several fault cases are simulated for the test distribution system, and the load balancing index of the proposed solution is compared with all of feasible solutions.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.6
• /
• pp.744-749
• /
• 2013

The protection switching technology is widely adopted in the fiber-optical transmission equipments based on TDM(Time Division Multiplexing), such as PDH, SDH/SONET. A variety of protection switching algorithms for Ethernet networks and the progress of standardization are summarized in the document. There are several kinds of protection switching algorithms for Ethernet networks, such as STP, RSTP, MSTP and etc. However, since Ethernet signal move through detour route, it causes much time to recover. Accordingly, it is difficult to secure a usability of Ethernet networks and QOS(Quality of Service). Also, if the protection switching protocol standardized by IEEE and ITU-T is used, it remains a inherent network switching time for protection. Therefore, a specific protection switching algorithm for Ethernet are needed for seamless and stable operation of Ethernet networks service for Distribution Automation System(DAS). A reliable protection algorithm with no switching delay time is very important to implement Self-healing service for DAS. This study of FPGA based protection switching algorithm for Ethernet networks shows that in case of faults occurrence on distribution power network, immediate fault isolation and restoration are conducted through interaction with distribution equipments using P2P(Peer to Peer) communication for protection coordination. It is concluded that FPGA based protection switching algorithm for Ethernet networks available 0ms switching time is crucial technology to secure reliability of DAS.

• International Journal of Control, Automation, and Systems
• /
• v.3 no.4
• /
• pp.591-600
• /
• 2005

In this paper, we discuss real-time control of networked control systems (NCSs) and practical issues in the choice of the communication networks for this purpose. An appropriate integration of control systems, real-time environments, and network communication systems allows the optimization of the quality-of-control (QoC) in NCSs. We compare several prevailing network types that may be used in control applications to offer a guideline of choosing a proper network. A real-time operating environment is also presented as an important ingredient of NCS design. To evaluate its feasibility and effectiveness, a real-time NCS containing a ball magnetic levitation (Maglev) setup is implemented via an Ethernet. Based on the experimental results, it is concluded in this paper that real-time control via Ethernet is a practical and feasible solution to NCS design.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1117-1120
• /
• 2002

In general, standard TCP/IP (transmission control protocol-internet protocol), which is called TCP/IP, is using as the communication basis protocol between any collections of networks that is connected. In this paper, using this TCP/IP implementation of remote system and suitable program for long distance communication is proposed. This system can make system, which basic Ethernet and TCP/IP used system, to mini modeling, so all module that is using here can be used. Therefore, intention of this paper is to reduce expenses, to effective manage for plant and to increase of productivity as linking each plant of several factories to TCP/IP and Ethernet, and then many control plant and manager minimize the needed course.

• Journal of Energy Engineering
• /
• v.14 no.2 s.42
• /
• pp.112-116
• /
• 2005

This paper describes the implementation of DCS communication network that provides high bandwidth and reliability. The network for DCS in this paper adopts the Reflective Memory (RM) architecture and Fast Ethernet physical media that have 100 Mbps bandwidth. Also, This network uses Ring Enhancement Device (RED) which is invented to reduce the time delay of each node. The DCS network that is introduced in this paper is named as ERCNet (Ethernet based Real-time Control Network). This paper describes the architecture and working algorithms of ERCNet and performs numerical analysis. In addition, the performance of ERCNet is evaluated by experiment using the developed ERCNet network.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.4 no.4
• /
• pp.293-300
• /
• 2009

In this paper, we describe a method for synchronization protocol method used in control system based on network and IEEE 1599 synchronization method which used for implementation of synchronization technology of advanced industrial Ethernet. We also implement and perform the experiment for synchronization technology of EtherCAT communication which is one of the industrial Ethernet technology used IEEE 1599 synchronization technology based on time. And we describe an evaluation for experiment result, improve the problem and future plan.