• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.5
• /
• pp.432-436
• /
• 2019

In this study, we produced a light, flexible, wearable gas sensor by depositing MWCNTs (Multi-walled Carbon Nanotubes) into nylon. MWCNTs are widely used as a gas sensor material due to their excellent mechanical, electrical and physical characteristics. We produced a gas sensor to detect NOx gases by depositing nylon yarn in a MWCNT solution. The MWCNT solution was made by mixing 3 mg MWCNT in 5 ml of ethanol. Nylon yarn was placed in the manufactured solution and ultrasonic waves were applied using an ultrasonicator for 3 h, resulting in MCWNT deposition. The MWCNT-deposited nylon yarn was dried at room temperature for 24 h. The MWCNT-thin-film-coated nylon yarn was masked 1 mm apart, and gold was then deposited on the masked nylon yarn to create the gas sensor. The sensor then was installed in a chamber with a controlled atmospheric environment and exposed to NOx gas. The changing signal from the sensor was amplified to analyze its gas detection characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.483-486
• /
• 2000

In the recognition of the gases using the quartz crystal rnicrobalance (QCM) coated with the film materials, it is important to obtain the recognition ability of gases, and the stability of film coated above the QCM. Especially, the thickness of film coated above the QCM is decreased according with the using circumstance and time of QCM gas sensor. Therefore, the sensing chararcteristics of film is changed with these. In this paper, we coated the lipid GC materials varing with the blended amount of PVC(Po1y Vinyl Chloride) and solution (Tetra Hydrofan:THF) above QCM to obtain the stability of lipid PC film. QCM gas sensors coated with film materials were measured the frequency change in the chamber of stationary gas sensing system injected 1-hexane, ethyl acetate, ethanol and benzene of 20.4 respectively. Also, we measured the degradation characteristics of QCM gas sensor to show the properties of stability.

• Journal of Sensor Science and Technology
• /
• v.28 no.3
• /
• pp.171-176
• /
• 2019

The biomarkers related to the colorectal cancers and diseases were surveyed and summarized, and an optical electronic nose was researched and developed for their analysis. The prototyped sensor revealed that it could discriminate two gases: ethanol 2000 ppm and $CO_2$ 500 ppm. Furthermore, the sensor demonstrated the potential capability of estimation of $CO_2$ concentration with 95% confidence level. Based on the above experimental results, the developed optical electronic nose was tested with the mixtures of gases (Isopropyl Alcohol, Acetone, Methanol, and Toluene) and the biomarkers were successfully segregated using principal component analysis.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.1
• /
• pp.75-80
• /
• 2016

$In_2O_3$ nanowires were coated with $Co_3O_4$ nanoparticles to investigate the improvement of ethanol gas sensing performance compared with as-synthesized $In_2O_3$ nanowires. Scanning electron microscopy showed that the nanowires synthesized by VLS mechanism had diameters and lengths of approximately 50-100 nm and a few micrometers, respectively. $Co_3O_4$ nanoparticles produced by hydrothermal method was in the size range of a few to a few tens nm. As-synthesized and $Co_3O_4$ nanoparticles coated $In_2O_3$ nanowires sensors exhibited responses of 1.96% and 4.57%, respectively for the ethanol gas concentration of 200 ppm at $200^{\circ}C$. The underlying mechanism for the improved responses of $Co_3O_4$ nanoparticles coated $In_2O_3$ nanowires sensors is discussed.

• Journal of Sensor Science and Technology
• /
• v.16 no.1
• /
• pp.39-43
• /
• 2007

This paper presents characteristics of surface acoustic wave (SAW) gas sensor for detecting volatile gases such as acetone, methanol, and ethanol by measuring phase shift of output signal. A delay-line by combining with a center frequency of 200 MHz was fabricated on S-T Quartz substrates. Using gas chromatography column, the selectivity of the SAW gas sensor were introduced. Experimental results, which show the phase change of output signal under the absorption of volatile gas on sensor surface, were presented. This SAW gas sensor system may be well suited for a high performance electronic nose system.

• Journal of Sensor Science and Technology
• /
• v.27 no.4
• /
• pp.221-226
• /
• 2018

Misfueling accidents significantly damage the engines of both gasoline and diesel vehicles, and should be avoided by rapid and accurate fuel discrimination. Gasoline fuel contains bioethanol. Thus, the detection of ethanol vapor produced by gasoline can be used to distinguish between gasoline and diesel. In the present study, Pt-doped $SnO_2$ hollow nanospheres, Mg-doped $In_2O_3$ hollow microspheres, and Pt-doped ZnO nanostructures have been used as gas sensors to discriminate between gasoline and diesel fuels. All three sensors are able to detect and discriminate between gases evaporating from gasoline and diesel. Among the sensors, the Mg-doped $In_2O_3$ hollow microspheres show a significant gas response (resistance ratio = 4.97) quickly (~3 s) after exposure to gasoline-evaporated gas at $225^{\circ}C$, but did not show any substantial response to diesel-evaporated gas. This demonstrates that gasoline and diesel fuels can be discriminated using small and cost-effective oxide semiconductor gas sensors.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.5
• /
• pp.35-40
• /
• 2005

An experimental Investigation of the basic characteristics of a micro-cantilever sensor was performed by inspecting the amplitude and frequency characteristics of a commercial tuning fork (TF). Application of acetone and ethanol with a volume of $1{\mu}l$ on the tine of a vibrating tuning fork causes immediate response in its amplitude and frequency characteristics. It has been shown that the tuning fork has ability to recognize a chemical agent with high sensitivity. The theoretical sensitivity of mass loading is in the range of $\~0.1Hz/ng$. Quartz tuning forks are routinely made using standard microfabrication process, thus suggesting the possibility of microfabrication of micro quart sensors.

• Journal of Powder Materials
• /
• v.26 no.1
• /
• pp.28-33
• /
• 2019

The gas sensor is essential to monitoring dangerous gases in our environment. Metal oxide (MO) gas sensors are primarily utilized for flammable, toxic and organic gases and $O_3$ because of their high sensitivity, high response and high stability. Tungsten oxides ($WO_3$) have versatile applications, particularly for gas sensor applications because of the wide bandgap and stability of $WO_3$. Nanosize $WO_3$ are synthesized using the hydrothermal method. As-prepared $WO_3$ nanopowders are in the form of nanorods and nanorulers. The crystal structure is hexagonal tungsten bronze ($MxWO_3$, x =< 0.33), characterized as a tunnel structure that accommodates alkali ions and the phase stabilizer. A gas detection test reveals that $WO_3$ can detect acetone, butanol, ethanol, and gasoline. This is the first study to report this capability of $WO_3$.

• Journal of Sensor Science and Technology
• /
• v.25 no.3
• /
• pp.218-222
• /
• 2016

Pure and V-doped NiO porous structures were prepared by the evaporation-induced surfactant assembly and subsequent pyrolysis of assembled structures, and their gas sensing characteristics were investigated. Pure NiO porous structures showed negligible gas responses (S=$R_g/R_a$, $R_g$: sensor resistance in analytic gas; $R_a$: sensor resistance in air) to 5 ppm trimethylamine (S=1.17) as well as other interfering gases such as ethanol, p-xylene, toluene, benzene and formaldehyde (S=1.02-1.13). In contrast, the V-doped NiO porous structures exhibited a high response and selectivity to 5 ppm trimethylamine (S=14.5) with low cross-responses to other interfering gases (S=4.0-8.7) at $350^{\circ}C$. The high gas response of V-doped NiO porous structures to trimethylamine was explained by electronic sensitization, that is, the increase in the chemoresistive variation due to the decrease in the hole concentration. The enhanced selectivity to trimethylamine was discussed in relation to the interaction between basic trimethylamine gas and acidic V catalysts.

• Journal of Sensor Science and Technology
• /
• v.16 no.5
• /
• pp.349-354
• /
• 2007

This paper presents characteristics of surface acoustic wave (SAW) gas sensor for detecting volatile gases such as ethanol gas by measuring the phase shift of output signal. A delay-line with a center frequency of 400 MHz was fabricated on $128^{\circ}$ Y-Z $LiNbO_{3}$ substrates. Experimental results, which showed the phase change of the output signal under the absorption of volatile gas on sensor surface, were presented. The sensitivities of SAW delay lines coated with polyurethane films were greatly increased compared to those for uncoated devices. This SAW gas sensor system may be well suited for a high sensitivity electronic nose system.