• Proceedings of the Korean Magnestics Society Conference
• /
• 2011.12a
• /
• pp.29-30
• /
• 2011

We have demonstrated the fabrication of sub 30 nm MTJ pillars with PMA characteristics. The multi-step IBE process performed at $45^{\circ}$ and $30^{\circ}$, using NER resulted in almost vertical side profiles. There deposition on the sidewalls of the NER prevented lateral etching of the resist hard mask allowing vertical MTJ side profile formation without any reduction in the lithographically defined resist lateral dimensions. For the 28nm STT-MTJ pillars, the measured TMR ratio was 13 % with resistance of 1 $k{\Omega}$, which was due to remaining redeposition layers less than 0.1 nm thick. With further optimization in multi-step IBE conditions, it will be possible to fabricate fully operating sub 30 nm perpendicular STT-MTJ structures for application to future non-volatile memories.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.4
• /
• pp.1993-1998
• /
• 2011

Semiconductor industry needs to have fine patterns in order to fabricate the high density integrated circuit. For nano-scale patterns, hard-mask is used to multi-layer structure which is formed by CVD (chemical vaporized deposition) process. In this work, we prepared single-layer hard-mask by using organic-inorganic hybrid polymer for spin-on process. The inorganic part of hard-mask was much easier etching than photo resist layer. Beside, the organic part of hard-mask was much harder etching than substrate layer. We characterized the optical and morphological properties to the hard mask films using organic-inorganic hybrid polymer, and then etch rate of photo resist layer and hard-mask film were compared. The hybrid polymer prepared from organic and inorganic materials was found to be useful hard-mask film to form the nano-patterns.

• The korean journal of orthodontics
• /
• v.20 no.3 s.32
• /
• pp.583-591
• /
• 1990

If the bond strength is sufficient to resist orthodontic force, orthodontic brackets can be bonded to restorations. Orthodontic brackets were bonded to composite resin and glass ionomer cement restorations with no-mix adhesive or glass ionomer cement. The shear bond strength of adhesives bonded to restorations was studied in vitro. Orthodontic brackets were bonded to 10 extracted natural teeth, 40 composite resin restorations and 40 glass ionomer restorations. The surfaces of composite resin restorations were roughened or applied with bonding agent (Scothbond) after surface roughening. The surfaces of glass ionomer cement restorations were conditioned with acid etching or applied with Scotchbond to etched surface. The adhesive was no-mix resin or glass ionomer cement. The shear bond strength was measured. The results were as follows: 1. Orthodontic brackets could be bonded to composite resin restorations effectively as they could be bonded to acid etched enamel with no-mix adhesive. The shear bond strength was sufficient to resist orthodontic force and was not affected by bonding agent greatly. 2. The shear bond strength of no-mix adhesive bonded to acid etched glass ionomer cement restorations was sufficient to resist orthodontic force. However. the fracture risk of glass ionomer cement restorations was increased during debonding. The bonding agent couldn't increase the shear bond strength greatly. 3. The shear bond strength of glass ionomer cement bonded to glass ionomer cement restorations was lower than that of no-mix adhesive. The shear bond strength was sufficient to resist orthodontic force and was greatly decreased by bonding agent. 4. The shear bond strength of glass ionomer cement bonded to composite resin restorations was too low to resist orthodontic force.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.326-329
• /
• 2005

As a flexible method to fabricate sub-micrometer patterns, Focused Ion Beam (FIB) instrument and Self-Assembled Monolayer (SAM) resist are introduced in this work. FIB instrument is known to be a very precise processing machine that is able to fabricate micro-scale structures or patterns, and SAM is known as a good etch resistance resist material. If SAM is applied as a resist in FIB processing fur fabricating nano-scale patterns, there will be much benefit. For instance, low energy ion beam is only needed for machining SAM material selectively, since ultra thin SAM is very sensitive to $Ga^+$ ion beam irradiation. Also, minimized beam spot radius (sub-tens nanometer) can be applied to FIB processing. With the ultimate goal of optimizing nano-scale pattern fabrication process, interaction between SAM coated specimen and $Ga^+$ ion dose during FIB processing was observed. From the experimental results, adequate ion dose for machining SAM material was identified.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1269-1271
• /
• 2008

We find some array mura are caused by S/D bridge or channel open in 4 mask process. The gray tone PR thickness non-uniformity is the main reason of these defects. By the adjustment of exposure and dry etch parameters, S/D bridge and channel open ratio drops by 10.87%.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.3
• /
• pp.55-60
• /
• 2020

The hard mask photo-resist strip inspection system for the semiconductor wafer manufacturing process inspects the position of the circuit pattern formed on the wafer by measuring the distance from the edge of the wafer to the strip processing area. After that, it is an inspection system that enables you to check the process status in real time. Process defects can be significantly reduced by applying a tester that has not been applied to the existing wafer strip process, edge etching process, and wafer ashing process. In addition, it is a technology for localizing semiconductor process inspection equipment that can analyze the outer diameter of the wafer and the state of pattern formation, which can secure process stability and improve wafer edge yield.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.8
• /
• pp.1436-1440
• /
• 2007

Beryllium copper has been known to be an important material for the various fields of industry because it can be used for mechanical and electrical/electronic components that are subjected to elevated temperatures (up to $400^{\circ}C$ for short times). Blade type tip for probing the cells of liquid crystal display(LCD) was fabricated using beryllium copper foil. The dry film resist was employed as a mask for patterning of the blade type tip. The beryllium copper foil was etched using hydrochloric acidic iron-chloride solution. The concentration, temperature, and composition ratio of hydrochloric acidic iron-chloride solution affect the etching characteristics of beryllium copper foil. Nickel with the thickness of $3{\mu}m$ was electroplated on the patterned copper beryllium foil for enhancing its hardness, followed by electroplating gold for increasing its electrical conductivity. Finally, the dry film resist on the bridge was removed and half of the nickel was etched to complete the blade type tip.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1343-1345
• /
• 1998

This work was carried out to develop a pattern on the nanometer scale using plasma polymerization and plasma etching. This study is also aimed at developing a resist for the nano process and a vacuum lithography process. The thin films of plasma polymerization were fabricated by the plasma polymerization of inter-electrode capacitively coupled gas flow system. After delineating the pattern at accelerating voltage of 30[kV], ranging the dose of $1-500[{\mu}C/cm^2$], the pattern was developed with dry type and formed by plasma etching.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.65 no.1
• /
• pp.57-65
• /
• 2016

This paper was analyzed the characteristics of piezoelectric inkjet print head using finite element method(FEM). It showed the bending node driving of piezoelectric and relation theory principle consider piezoelectric material characteristics and ink characteristics. From such result we were had the piezoelectric head design and manufacture. It got a this head characteristics through experiment, we confirmed that proper voltage control is possible to through ink drop control experiment of piezoelectric print head. This paper was obtained the suitable ink jetting characteristics that manufacture the control circuit and piezoelectric inkjet print head. This practice product was applied to improvement of PCB electric circuit pattern by etching resist ink that PCB manufactured to complex process over traditional 6 stages can be simpled to 1 stage by inkjet printing technology.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.17-20
• /
• 2000

We have enhanced the yield of 0.25 ${\mu}{\textrm}{m}$ T-gate $Al_{0.25}$G $a_{0.75}$As/I $n_{0.2}$G $a_{0.8}$As P-HEMT using three-layer E-beam lithography process and selective etching process. The three-layer resist structure (PMMA/copolymer/ PMMA=2000 $\AA$/3000 $\AA$/2000 $\AA$) and three developers (Benzene：IPA=1：1,Methanol：IPA =1：1,MIBK：IPA=1：3) were used for fabrication of a wide-head T-gate by the conventional double E-beam exposure technology. Also 1 wt% citric acid： $H_2O$$_2$：N $H_{4}$OH(200m1：4ml：2.2ml) solution were used for uniform gate recess. The etching selectivity of GaAs over $Al_{0.25}$G $a_{0.75}$As is measured to be 80. So these P-HEMT processes can be used in X-band MMIC LNA fabrication.ion.ion.ion.