• Nuclear Engineering and Technology
• /
• v.52 no.4
• /
• pp.827-834
• /
• 2020

Damage of tungsten due to helium ions of a PF device was studied. The tungsten was analyzed by SEM and AFM after irradiation. SEM revealed fine bubbles of helium atoms with diameters of a few nanometers, which join and form larger bubbles and blisters on the surface of tungsten. This observation confirmed the results of molecular dynamics simulation. SEM analysis after etching of the irradiated surface indicated cavities with depth range of 35-85 nm. The average fluence of helium ion of the PF device was calculated about 5.2 × 10¹⁵ cm^-2 per shot, using Lee code. Energy spectrum of helium ions was estimated using a Thomson parabola spectrometer as a function of dN/dE ∝ E^-2.8 in the energy range of 10-200 keV. The characteristics of helium ion beam was imported to SRIM code. SRIM revealed that the maximum DPA and maximum helium concentration occur in the depth range of 20-50 nm. SRIM also showed that at depth of 30 nm, all of the tungsten atoms are displaced after 20 shots, while at depth of higher than 85 nm the destruction is insignificant. There is a close match between SRIM results and the measured depths of cavities in SEM images of tungsten after etching.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.423.1-423.1
• /
• 2014

본 발표에서는 실리콘 이종접합 태양전지에서 중요한 실리콘 웨이퍼 표면/계면 제어에 대하여 발표한다. 다시 말하여, 실리콘 웨이퍼 기판 세정공정 변화에 따른 실리콘 웨이퍼 표면의 소수전하수명(minority carrier lifetime, MCLT) 및 태양전지 소자특성 변화에 대하여 연구하였다. 구체적으로, 실리콘 웨이퍼 클리닝 최초단계로써 KOH damage etching 공정을 도입할 때, 이후 클리닝 공정을 통일하여 적용한 웨이퍼 표면의 MCLT 및 상기 웨이퍼를 이용하여 플라즈마 화학기상증착법(PECVD)을 통하여 제작한 태양전지 소자 효율은 KOH etching 시간이 10분일 때 최대치에 도달한 후 감소하였다. 또한, RCA1, RCA2, Piranha로 이루어진 웨이퍼 클리닝 단계의 사이에, 또는 맨 마지막에 묽힌 불산용액(DHF, 5 %) 처리를 하여 표면 산화막 제거 및 수소종단처리를 하여 기판의 passivation 특성을 향상시키고자 할 때, 불산용액 처리 순서에 따른 웨이퍼 표면의 MCLT 및 태양전지 소자 효율을 비교하였다. 그 결과, 묽은불산용액을 클리닝 단계 사이에 적용하였을 때의 MCLT 및 태양전지 소자의 특성이 더 우수하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1224-1231
• /
• 2003

This paper reports on the air-gap type thin film bulk acoustic wave resonator(FBAR) using ultra thin wafer with thickness of 50$\mu\textrm{m}$. It was fabricated to realize a small size devices and integrated objects using MEMS technology for flexible microsystems. To reduce a error of experiment, MATLAB simulation was executed using material characteristic coefficient. Fabricated thin FBAR consisted of piezoelectric film sandwiched between metal electrodes. Used piezoelectric film was the aluminum nitride(AlN) and electrode was the molybdenum(Mo). Thin wafer was fabricated by wet etching and dry etching, and then handling wafer was used to prevent damage of FBAR. The series resonance frequency and the parallel frequency measured were 2.447㎓ and 2.487㎓, respectively. Active area is 100${\times}$100$\mu\textrm{m}$$^2$.Q-factor was 996.68 and K$^2$$\_$eff/ was 3.91％.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.101-102
• /
• 2006

PZT thin films, which are the representative ferroelectric materials in ferroelectric random access memory (FRAM), have some serious problem such as the imprint, retention and fatigue which ferroelectric properties are degraded by repetitive polarization. BL T thin film capacitors were fabricated by plasma etching, however, the plasma etching of BLT thin film was known to be very difficult. In our previous study, the ferroelectric materials such as PZT and BLT were patterned by chemical mechanical polishing (CMP) using damascene process to top electrode/ferroelectric material/bottom electrode. It is also possible to pattern the BLT thin film capacitors by CMP, however, the CMP damage was not considered in the experiments. The properties of BLT thin films were changed by the change of polishing pressure although the removal rate was directly proportional to the polishing pressure in CMP process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.4
• /
• pp.261-266
• /
• 1998

In developing the high density memory device, the etching of fine pattern is becoming increasingly important. Therefore, definition of ultra fine line and space pattern and minimization of damage and contamination are essential process. Also, the high density plasma in low operating pressure is necessary. The candidates of high density plasma sources are electron cyclotron resonance plasma, helicon wave plasma, helical resonator, and inductively coupled plasma. In this study, planar type magnetized inductively coupled plasma etcher has been built. The density and temperature of Ar plasma are measured as a function of rf power, flow rate, external magnetic field, and pressure. The oxide etch rate and selectivity to polysilicon are measured as the above mentioned conditions and self-bias voltage.

• Current Photovoltaic Research
• /
• v.6 no.1
• /
• pp.27-30
• /
• 2018

The dependency of the electrical characteristics of silicon solar-cells on the depth of damaged layer induced by wire-sawing process was investigated. To compare cell efficiency with residual sawing damage, silicon solar-cells were fabricated by using as-sawn wafers having different depth of saw damage without any damaged etching process. The damaged layer induced by wire-sawing process in silicon bulk intensely influenced the value of fill factor on solar cells, degrading fill factor to 57.20%. In addition, the photovoltaic characteristics of solar cells applying texturing process shows that although the initial depth of saw-damage induced by wire-sawing process was different, the value of short-circuit current, fill-factor, and power-conversion-efficiency have an almost same, showing ~17.4% of cell efficiency. It indicated that the degradation of solar-cell efficiency induced by wire-sawing process could be prevented by eliminating all damaged layer through sufficient pyramid-surface texturing process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.363-363
• /
• 2008

The development of dry etching process for sapphire wafer with plasma has been key issues for the opto-electric devices. The challenges are increasing control and obtaining low plasma induced-damage because an unwanted scattering of radiation is caused by the spatial disorder of pattern and variation of surface roughness. The plasma-induced damages during plasma etching process can be classified as impurity contamination of residual etch products or bonding disruption in lattice due to charged particle bombardment. Therefor, fine pattern technology with low damaged etching process and high etch rate are urgently needed. Until now, there are a lot of reports on the etching of sapphire wafer with using $Cl_2$/Ar, $BCl_3$/Ar, HBr/Ar and so on [1]. However, the etch behavior of sapphire wafer have investigated with variation of only one parameter while other parameters are fixed. In this study, we investigated the effect of pressure and other parameters on the etch rate and the selectivity. We selected $BCl_3$ as an etch ant because $BCl_3$ plasmas are widely used in etching process of oxide materials. In plasma, the $BCl_3$ molecule can be dissociated into B radical, $B^+$ ion, Cl radical and $Cl^+$ ion. However, the $BCl_3$ molecule can be dissociated into B radical or $B^+$ ion easier than Cl radical or $Cl^+$ ion. First, we evaluated the etch behaviors of sapphire wafer in $BCl_3$/additive gases (Ar, $N_2,Cl_2$) gases. The behavior of etch rate of sapphire substrate was monitored as a function of additive gas ratio to $BCl_3$ based plasma, total flow rate, r.f. power, d.c. bias under different pressures of 5 mTorr, 10 mTorr, 20 mTorr and 30 mTorr. The etch rates of sapphire wafer, $SiO_2$ and PR were measured with using alpha step surface profiler. In order to understand the changes of radicals, volume density of Cl, B radical and BCl molecule were investigated with optical emission spectroscopy (OES). The chemical states of $Al_2O_3$ thin films were studied with energy dispersive X-ray (EDX) and depth profile anlysis of auger electron spectroscopy (AES). The enhancement of sapphire substrate can be explained by the reactive ion etching mechanism with the competition of the formation of volatile $AlCl_3$, $Al_2Cl_6$ or $BOCl_3$ and the sputter effect by energetic ions.

• Membrane Journal
• /
• v.23 no.1
• /
• pp.92-99
• /
• 2013

In this study the nanofiltration (NF) membrane treatment of a sulfuric acid waste solutions containing copper ion ($Cu^{+2}$) discharging from the etching processes of the printed circuit board (PCB) manufacturing industry has been studied for the recycling of acid etching solution. SelRO MPS-34 4040 NF membrane from Koch company was tested to obtain the basic NF data for recycling of etching solution and separation efficiency (total rejection) of copper ion. NF experiments were carried out with a dead-end membrane filtration laboratory system. The pure water flux was increased with the increasing storage time in sulfuric acid solution and lowering pH of acid solution because of the enhancement of NF membrane damage by sulfuric acid. The permeate flux of acid solution was decreased with the increasing copper ion concentration. Total rejection of copper ion was decreased with the increasing storage time in sulfuric acid solution and copper ion concentration, and lowering the pH of acid solution. The total rejection of copper ion was decreased from initial 37% to 15% minimum value.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.222.2-222.2
• /
• 2016

트랜지스터 응용 등에 관한 연구가 활발해 지면서 에너지 밴드갭이 0 eV에 가까운 그래핀 이외의 밴드 갭 조절이 가능한 MoS2 (molybdenum disulfide), BN (boron nitride), Bi2Te3 (bismuth telluride), WS2 (tungsten disulfide) 등과 같은 이차원 Transition Metal DiChalcogenides (TMDC) 물질이 반도체 물질로 각광받고 있다. 특히 MoS2의 경우 단결정 덩어리 상태에서는 약 1.3 eV의 밴드갭을 가지나 두께가 줄어들어 두 층일 경우에는 약 1.65 eV, 단일층이 되면 약 1.9 eV의 밴드갭을 가져 박막 층수에 따라 에너지 밴드갭 조절이 가능한 것으로 알려져있다. 하지만 두께 조절이 가능하면서 대면적, 고품질을 가지는 MoS2 박막 합성은 아직 제한적이라 할 수 있으며 새로운 방법 및 물질에 대한 연구가 지속적으로 이루어 지고 있다. 따라서 본 연구에서는 다양한 층수를 지니는 MoS2 합성을 위해 나노 두께의 MoS2 박막을 CF4 plasma 를 이용하여 layer etching 진행하고 CF4 plasma 100초 etching 진행한 2 layer 두께의 MoS2를 기준으로 H2S plasma를 이용하여 treatment 진행하였다. 물리적, 화학적 분석은 Raman spectroscopy, XPS(X-ray Photoelectron Spectroscopy), AFM (Atomic Force Microscopy) 등을 이용해 진행하였고 이를 통해 MoS2 layer 감소 및 damage recovery 등을 확인하였다.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.2
• /
• pp.41-47
• /
• 1999

In this paper, we report 3D-simulations of a plasma etching process by employing cell-removal algorithm takes into account the mask shadow effect os well as spillover errors. The developed simulator haas an input interface to take not only an analytic form but a Monte Carlo distribution of the ions. The graphic user interface(GUI) was also built into the simulator for UNIX environment. To demonstrate the capability of 3D-SURFILER(SURface proFILER), we have simulated for a typical contact hole structure with 36,000($30{\times}40{\times}30$) cells, which takes about 20 minutes with 10 Mbytes memory on sun ultra sparc 1. as an exemplary case, we calculated the etch profile during the reactive ion etching(RIE) of a contact hole wherein the aspect ratio is 1.57. Furthermore, we also simulated the dependence of a damage parameter and the evolution of topography as a function of the chamber pressure and the incident ion flux.