• Journal of the Korean Vacuum Society
• /
• v.6 no.2
• /
• pp.103-108
• /
• 1997

Silicon field emitter arrays (FEAs) have been fabricated by a novel method employing a two-step tip etch and a spin-on-glass (SOG) etch-back process using double layered thermal/tetraethylortho-silicate (TEOS) oxides as a gate dielectric. A partial etching was performed by coating a low viscous photo resist and $O_2$ plasma ashing on order to form the double layered gate dielectric. A small gate aperture with low gate leakage current was obtained by the novel process. The hight and the end radius of the fabricated emitter was about 1.1 $\mu\textrm{m}$ and less than 100$\AA$, respectively. The anode emission current from a 256 tips array was turned-on at a gate voltage of 40 V. Also, the gate current was less than 0.1% of the anode current.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.58-61
• /
• 2002

SBT thin films were etched at different content of Cl$_2$in Cl$_2$/Ar plasma. We obtained the maximum etch rate of 883 ${\AA}$/min at Cl$_2$(20%)/Ar(80%). As Cl$_2$ gas increased in Cl$_2$/Ar plasma, the etch rate decreased. The maximum etch rate may be explained by variation of volume density for Cl atoms and by the concurrence of two etching mechanisms such as physical sputtering and chemical reaction with formation of low-volatile products, which can be desorbed only by ion bombardment. The variation of volume density for Cl, F and Ar atoms and ion current density were measured by the optical emission spectroscopy and Langmuir probe. To evaluate the physical damage due to plasma, X-ray diffraction and atomic force microscopy analysis carried out. After etching process, P-E hysteresis loops were measured by ferroelectric workstation.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.04a
• /
• pp.87-96
• /
• 2000

The properties of polyimide for interlayer dielectric applications are investigated during plasma etching of aluminum on it. Chlorine-based plasma generally used for aluminum etching results in an increase in the (dielectric constant of polyimide, while $SF_6$ plasma exhibits a high polyimide etch rate and a reducing effect of the dielectric constant. The leakage current of polyimide is significantly suppressed after plasma exposure. An optimal combination of Al etch with $Cl_6$ plasma and polyimide etch with $SF_6$ plasma is expected to be a good tool for realizing multilevel metallization structures.

• Electrical & Electronic Materials
• /
• v.7 no.4
• /
• pp.294-299
• /
• 1994

CHF$_{3}$/CH$_{4}$Ar 플라즈마에 의해 형성된 산화막 식각 잔류물의 화학구조와 이 잔류물의 제거를 위한 세정방법을 x-ray photoelectron spectroscopy를 이용하여 조사하였다. 잔류무르이 구조는 CF$_{x}$-polymer와 Si-C, Si-O 결합으로 이루어진 SiO$_{y}$ C$_{z}$ 이었다. CF$_{4}$O$_{2}$ 플라즈마에 의한 silicon light etch는 산화막 식각 잔류물인 SiO$_{y}$ C$_{z}$ 층과 손상된 실리콘 표면을 제거하엿으며 NH$_{4}$OH-H$_{2}$O$_{2}$과 HF용액으로 완전히 제거되는 CF$_{x}$-polymer/SiO$_{x}$층을 남겼다. 100.angs.정도의 silicon light etch는 minority carrier life time과 thermal wave signal값을 초기 웨이퍼 수준까지 회복시켰으며 접합누설 전류도 거의 습식 식각 공정수준까지 감소시켰다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.417-420
• /
• 2004

The electrical effects of dry-etch on n-type GaN by an inductively coupled $Cl_2/CH_4/H_2/Ar$ plasma were investigated as a function of ion energy, by means of ohmic and Schottky metallization method. The specific contact resistivity(${\rho}_c$) of ohmic contact was decreased, while the leakage current in Schottky diode was increased with increasing ion energy due to the preferential sputtering of nitrogen. At a higher rf power, an additional effect of damage was found on the etched sample, which was sensitive to the dopant concentration in terms of the ${\rho}_c$ of ohmic contact. This was attributed to the effects such as the formation of deep acceptor as well as the electron-enriched surface layer within the depletion layer. Furthermore, thermal annealing process enhanced the ohmic and Schottky property of heavily damaged surface.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.1
• /
• pp.37-41
• /
• 2021

We report on the formation of anodic aluminum oxide (AAO) film using sulfuric acid containing cerium salt. When the temperature of the sulfuric acid containing cerium salt changes from 5 ℃ to 20 ℃, the current density and the thickness growth rate increase. The surface morphology of the AAO film change according to the temperature of the electrolytes. And that affected the breakdown voltage and the plasma etch rate. The breakdown voltage per unit thickness was the highest at 15 ℃, and the plasma etch rate was the lowest at 10 ℃ at 2.80 ㎛/h.

• Korean Journal of Materials Research
• /
• v.10 no.5
• /
• pp.369-374
• /
• 2000

In order to investigate the effects of addition of 1M sulfuric acid to the etching solution or 1M hydrochloric acid on the etching behavior of aluminum foil for electrolytic capacitors, the changes in the density of etch pit, the length and diameter of etch tunnels and the capacitance were analyzed using SEM, TEM, LCR meter etc. Sulfate ion as a corrosion inhibitor was contributed to the increase of the surface area comparing with chloride ion. By adding sul-furic acid the density of etch pit and the length of etched tunnel increased and the diameter of the tunnel decreased, resulting in the increase of capacitance. It was also shown that the capacitance decreased when the current density was below $0.9A/\textrm{cm}^2$, while remarkably increased in the other case.

• New & Renewable Energy
• /
• v.4 no.2
• /
• pp.74-80
• /
• 2008

To improve the blue responses of screen-printed single crystalline silicon solar cells, we investigated an emitter etch-back technique to obtain high emitter sheet resistances, where the defective dead layer on the emitter surface was etched and became thinner as the etch-back time increased, resulting in the monotonous increase of short circuit current and open circuit voltage. We found that an optimal etch-back time should be determined to achieve the maximal performance enhancement because of fill factor decrease due to a series resistance increment mainly affected by contact and lateral resistance in this case. To elucidate the reason for the fill factor decrease, we studied the resistance analysis by potential mapping to determine the contact and the lateral series resistance. As a result, we found that the fill factor decrease was attributed to the relatively fast increase of contact resistance due to the dead layer thinning down with the lowest contact resistivity when the emitter was contacted with screen-printed silver electrode.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.390-393
• /
• 2008

To improve the blue responses of screen-printed single crystalline silicon solar cells, we investigated an emitter etch-back technique to obtain high emitter sheet resistances, where the defective dead layer on the emitter surface was etched and became thinner as the etch-back time increased, resulting in the monotonous increase of short circuit current and open circuit voltage. We found that an optimal etch-back time should be determined to achieve the maximal performance enhancement because of fill factor decrease due to a series resistance increment mainly affected by contact and lateral resistance in this case. To elucidate the reason for the fill factor decrease, we studied the resistance analysis by potential mapping to determine the contact and the lateral series resistance. As a result, we found that the fill factor decrease was attributed to the relatively fast increase of contact resistance due to the dead layer thinning down with the lowest contact resistivity when the emitter was contacted with screen-printed silver electrode.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.3
• /
• pp.106-109
• /
• 2011

We investigated the etching characteristics of titanium nitride (TiN) thin film in $BCl_3$/Ar inductively coupled plasma. The etching parameters were the gas mixing ratio, radio frequency (RF) power, direct current (DC)-bias voltages and process pressures. The standard conditions were as follows: total flow rate = 20 sccm, RF power = 500 W, DC-bias voltage = -100 V, substrate temperature = $40^{\circ}C$, and process pressure = 15 mTorr. The maximum etch rate of TiN thin film and the selectivity of TiN to $Al_2O_3$ thin film were 54 nm/min and 0.79. The results of X-ray photoelectron spectroscopy showed no accumulation of etch byproducts from the etched surface of TiN thin film. The TiN film etch was dominated by the chemical etching with assistance by Ar sputtering in reactive ion etching mechanism, based on the experimental results.