• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.12
• /
• pp.691-699
• /
• 2004

SRM(Switched Reluctance Motor) drives require the accurate position information of the rotor. These informations are generally provided by a tacho generator or digital shaft-position encoder These speed sensors lower the system reliability and require special attention to noise. This paper describes a new approach to estimating SRM speed from measured terminal voltages and currents for speed sensorless control. The described method is based on the sliding mode observer. The rotor speed and position observers are estimated by the adaptation law using the real and estimated currents. However, the conventional adaptive sliding mode observer based on the variable structure control theory has some disadvantages that the estimated values including the high-frequency chattering and the steady state error generated due to the infinite feedback gain chosen and the discontinuous control input. To reduce the chattering and steady state error, an integrator is also inserted in the sliding mode observer strategy. The described adaptive sliding mode observer decreases the vibration to the switching hyper-plane of the sliding mode by adding integrator. The described methodology incorporates the Lyapunov algorithm to drive the rotor speed and the stator resistance such that it can overcome the problem of sensitivity in the face of SRM parameter variation. Also, without any mechanical information. The rotor speed of SRM is obtained form adaptive scheme. The described method is verified through the simulation and experiment.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.2
• /
• pp.574-592
• /
• 2016

Range-free localization algorithm computes a normal node's position by estimating the distance to anchors which know their actual position. In recent years, reliable anchor selection research has been gained a lot of attention because this approach improves localization accuracy by selecting the only subset of anchors called reliable anchor. The distance estimation accuracy and the geometric shape formed by anchors are the two important factors which need to be considered when selecting the reliable anchors. In this paper, we study the relationship between a relative position of three anchors and localization error. From this study, under ideal condition, which is with zero localization error, we find two conditions for anchor selection, thereby proposing a novel anchor selection algorithm that selects three anchors matched most closely to the two conditions, and the validities of the conditions are proved using two theorems. By further employing the conditions, we finally propose a novel range-free localization algorithm. Simulation results show that the proposed algorithm shows considerably improved performance as compared to other existing works.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.51 no.6
• /
• pp.258-266
• /
• 2002

This paper proposes the methodology of the image processing algorithm that estimates the pose of the inner-pipe crawling robot. The inner-pipe crawling robot is usually equipped with a lighting device and a camera on its head for monitoring and inspection purpose of defects on the pipe wall and/or the maintenance operation. The proposed methodology is using these devices without introducing the extra sensors and is based on the fact that the position and the intensity of the reflected light from the inner wall of the pipe vary with the robot posture and the camera. The proposed algorithm is divided into two parts, estimating the translation and rotation angle of the camera, followed by the actual pose estimation of the robot . Based on the fact that the vanishing point of the reflected light moves into the opposite direction from the camera rotation, the camera rotation angle can be estimated. And, based on the fact that the most bright parts of the reflected light moves into the same direction with the camera translation, the camera position most bright parts of the reflected light moves into the same direction with the camera translation, the camera position can be obtained. To investigate the performance of the algorithm, the algorithm is applied to a sewage maintenance robot.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2008.09a
• /
• pp.68-75
• /
• 2008

This paper describes the design and implementation of a low cost inertial navigation system(INS) using an inertial measurement unit(IMU), a digital compass, GPS, and an embedded system. The system has been developed for a transporter that load and unload ship blocks in a shipbuilding yard. When the transporter would move from place to place, they would periodically pass under obstructions that would obscure the GPS signal. This increases the error when estimating the position. Thus the INS has been used to improve position accuracy. INS is also capable of providing continuous estimates of the transporter's position and orientation. Even though IMU is typically very expensive, this INS is made of "low cost" components and the indirect Kalman filtering algorithm.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.3
• /
• pp.445-450
• /
• 2015

In the moving target problem, the velocity information of the moving target is very important as well as the high accuracy position information. To solve this problem, active researches are being conducted recently with combine the Time Difference of Arrival (TDOA) and Frequency Delay of Arrival(FDOA) measurements. However, since the FDOA measurement is utilizing the Doppler effect due to the relative velocity between the target source and the receiver sensor, it may be difficult to use the FDOA measurement if the moving target speed is not sufficiently fast. In this paper, we propose a method for estimating the position and the velocities of the target by using only the TDOA measurements for the low speed moving target in the indoor environment with sensor network. First, the target position and heading angle are obtained from the estimated positions of two attached transmitters on the target. Then, the target angular and linear velocities are also estimated. In addtion, we apply the Instrumental Variable (IV) technique to compensate the estimation error of the estimated target velocity. In simulation, the performance of the proposed algorithm is verified.

• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 2001.04b
• /
• pp.79-80
• /
• 2001

This study was conducted to estimate rooting and shooting in single-node cuttings (SNC) of roses 'Rote Rose' and 'Teresa' to several conditions: growth stage, node position, and leaf area of cutting, so that single-stemmed roses (SSR) could be used in rose factory system. There was no effects of growth stage of flowering shoots far cutting on the rooting and shooting of SNC in both of the two cultivars. However, the node position and leaf area of cuttings significantly affected the rooting and shooting of SNC: the speed was accelerated with larger leaf area and upper node cuttings, but the rate showed little difference as above 95%. Based on above results, rooting and shooting in SNC was forced by leaf area mainly, followed by node positions. On the other hand, flowering rate of shoots from SNC was improved mainly with larger leaf area in cuttings. Shoots of 45cm-longer, qualified for rose factory system, increased with lower node and larger leaf area significantly. Therefore, it could be said that the potential growth of shoots from SNC would be influenced mainly by leaf area, followed by node position on cutting.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.1
• /
• pp.248-254
• /
• 2013

In location finding system using spaced multi-sensor, there is the phenomenon that the position estimation accuracy is degraded by the location of signal sources and the sensors. This phenomenon is called GDOP(Geometric Dilution Of Precision) effect. and to minimize these effects, research is needed on how. In this paper, I will describe how to minimize GDOP effect, estimating possibility of GDOP using AOA(angle of arrival) information of spaced multi sensors, and removing sensor error factor in position estimation.

• Journal of the Korea Society of Computer and Information
• /
• v.15 no.1
• /
• pp.111-118
• /
• 2010

The proposed algorithm to be explained in this paper is the localization technique using directional antenna. Here, it is assumed that anchor node has the ability to transfer the azimuth of each sector using GPS modules, sector antenna, and the digital compass. In the conventional sensor network, the majority of localization algorithms were capable of estimating the position information of the sensor node by knowing at least 3 position values of anchor nodes. However, this paper has proposed localization algorithm that estimates the position of nodes to continuously move with sensor nodes and traveling nodes. The proposed localization mechanisms have been simulated in the Matlab. The simulation results show that our scheme performed better than other mechanisms (e.g. MCL, DV-distance).

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.6
• /
• pp.143-148
• /
• 2022

It is very important for metaverse, mobile robot, and user location services to analyze the images continuously taken using a mobile smartphone or robot's monocular camera to estimate the camera's location. So far, PnP-related techniques have been applied to calculate the position. In this paper, the camera's moving direction is obtained using the essential matrix in the epipolar geometry applied to successive images, and the camera's continuous moving position is calculated through geometrical equations. A new estimation method was proposed, and its accuracy was verified through simulation. This method is completely different from the existing method and has a feature that it can be applied even if there is only one or more matching feature points in two or more images.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.4 no.1
• /
• pp.101-110
• /
• 2004

The robots that will be needed in the near future are human-friendly robots that are able to coexist with humans and support humans effectively. To realize this, humans and robots need to be in close proximity to each other as much as possible. Moreover, it is necessary for their interactions to occur naturally. It is desirable for a robot to carry out human following, as one of the human-affinitive movements. The human-following robot requires several techniques: the recognition of the moving objects, the feature extraction and visual tracking, and the trajectory generation for following a human stably. In this research, a predictable intelligent space is used in order to achieve these goals. An intelligent space is a 3-D environment in which many sensors and intelligent devices are distributed. Mobile robots exist in this space as physical agents providing humans with services. A mobile robot is controlled to follow a walking human using distributed intelligent sensors as stably and precisely as possible. The moving objects is assumed to be a point-object and projected onto an image plane to form a geometrical constraint equation that provides position data of the object based on the kinematics of the intelligent space. Uncertainties in the position estimation caused by the point-object assumption are compensated using the Kalman filter. To generate the shortest time trajectory to follow the walking human, the linear and angular velocities are estimated and utilized. The computer simulation and experimental results of estimating and following of the walking human with the mobile robot are presented.