• Convergence Security Journal
• /
• v.7 no.1
• /
• pp.45-53
• /
• 2007

Finite failure NHPP models presented in the literature exhibit either constant, monotonic increasing or monotonic decreasing failure occurrence rates per fault. In this paper, Goel-Okumoto and Yamada-Ohba-Osaki model was reviewed, proposes the hyper-exponential distribution reliability model, which maked out efficiency application for software reliability. Algorithm to estimate the parameters used to maximum likelihood estimator and bisection method. For model determination and selection, explored goodness of fit (the error sum of squares). The methodology developed in this paper is exemplified with a software reliability random data set introduced by of Weibull distribution (shape 0.1 & scale 1) of Minitab (version 14) statistical package.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.7A
• /
• pp.623-631
• /
• 2010

In this paper, various of pilot-assisted channel estimation techniques for 3GPP LTE downlink are tested under multipath Rayleigh fading channel. At first, the conventional channel estimation techniques are applied with linear zero-forcing (ZF) equalizer, such as one dimensional least square (1-D LS) linear interpolation, two dimensional (2-D) wiener filter, the time and frequency dimension separate wiener filter and maximum likelihood estimator (MLE). Considering the practical implementation, we proposed two channel estimation techniques by combining time-dimension wiener filter and MLE in two manners, which showed a good tradeoff between system performance and complexity when comparing with conventional techniques. The nonlinear decision feedback equalizer (DFE) which can show a better performance than linear ZF equalizer is also implemented for mitigating inter-carrier interference (ICI) in our system. The complexity of these algorithms are calculated in terms of the number of complex multiplications (CMs) and the performances are evaluated by showing the bit error rate (BER).

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.10 no.3
• /
• pp.1-9
• /
• 2014

The inverse Rayleigh model distribution and Rayleigh distribution model were widely used in the field of reliability station. In this paper applied using the finite failure NHPP models in order to growth model. In other words, a large change in the course of the software is modified, and the occurrence of defects is almost inevitable reality. Finite failure NHPP software reliability models can have, in the literature, exhibit either constant, monotonic increasing or monotonic decreasing failure occurrence rates per fault. In this paper, proposes the inverse Rayleigh and Rayleigh software reliability growth model, which made out efficiency application for software reliability. Algorithm to estimate the parameters used to maximum likelihood estimator and bisection method, model selection based on mean square error (MSE) and coefficient of determination($R^2$), for the sake of efficient model, were employed. In order to insurance for the reliability of data, Laplace trend test was employed. In many aspects, Rayleigh distribution model is more efficient than the reverse-Rayleigh distribution model was proved. From this paper, software developers have to consider the growth model by prior knowledge of the software to identify failure modes which can helped.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.12
• /
• pp.4967-4986
• /
• 2015

Multi-hop relaying communications have great potentials in improving transmission performance by deploying relay nodes. The benefit is critically dependent on the accuracy of the channel state information (CSI) of all the transmitting links. However, the CSI has to be estimated. In this paper, we investigate the channel estimation problem in one-way multi-hop MIMO amplify-and-forward (AF) relay system, where both the two-hop and three-hop communication link exist. Traditional point-to-point MIMO channel estimation methods will result in error propagation in estimating relay links, and separately tackling the channel estimation issue of each link will lose the gain as part of channel matrices involved in multiple communication links. In order to exploit all the available gains, we develop a novel channel estimation model by structuring different communication links using the PARAFAC and PARATUCK2 tensor analysis. Furthermore, a two-stage fitting algorithm is derived to estimate all the channel matrices involved in the communication process. In particular, essential uniqueness is further discussed. Simulation results demonstrate the advantage and effectiveness of the proposed channel estimator.

• The Korean Journal of Applied Statistics
• /
• v.23 no.2
• /
• pp.263-274
• /
• 2010

Business survey index(BSI) is an economic forecasting index made on the basis of the past achievement of the company and enterpriser's plan and decision for the future. Even the index is very popular in economic situations, only a little research result is known to the public. In the paper we investigate statistical properties of BSI. We define population BSI in the finite population and estimate it unbiasedly. Also we derive the variance of the estimated BSI and its unbiased estimator. In addition, confidence interval of the estimated BSI is proposed. We asserte that confidence interval of the estimated BSI is more reasonable than the relative standard error.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.3
• /
• pp.530-543
• /
• 2013

This paper describes a control scheme of speed sensorless fuzzy direct torque control (FDTC) of permanent magnet synchronous motor for electric vehicle (EV). Electric vehicle requires fast torque response and high efficiency of the drive. Speed sensorless FDTC In-wheel PMSM drives without mechanical speed sensors at the motor shaft have the attractions of low cost, quick response and high reliability in electric vehicle application. This paper presents a new approach to estimate the speed of in-wheel electrical vehicles based on Model Reference Adaptive System (MRAS). The direct torque control suffers in low speeds due to the effect of changes in stator resistance on the flux measurements. To improve the system performance at low speeds, a PI-fuzzy resistance estimator is proposed to eliminate the error due to changes in stator resistance. High performance sensorless drive of the in-wheel motor based on MRAS with on line stator resistance tuning is established for four motorized wheels electric vehicle and the whole system is simulated by matalb/simulink. The simulation results show the effectiveness of the new control strategy. This proposed control strategy is extensively used in electric vehicle application.

• Journal of Korean Institute of Industrial Engineers
• /
• v.40 no.3
• /
• pp.283-290
• /
• 2014

In the flat panel display industry, to meet production target quantities and the deadline of production, the scheduler and dispatching systems are major production management systems which control the order of facility production and the distribution of WIP (Work In Process). Especially the delivery time is a key factor of the dispatching system for the time when a lot can be supplied to the facility. In this paper, we use survival analysis methods to identify main factors of the delivery time and to build the delivery time forecasting model. To select important explanatory variables, the cox proportional hazard model is used to. To make a prediction model, the accelerated failure time (AFT) model was used. Performance comparisons were conducted with two other models, which are the technical statistics model based on transfer history and the linear regression model using same explanatory variables with AFT model. As a result, the mean square error (MSE) criteria, the AFT model decreased by 33.8% compared to the statistics prediction model, decreased by 5.3% compared to the linear regression model. This survival analysis approach is applicable to implementing the delivery time estimator in display manufacturing. And it can contribute to improve the productivity and reliability of production management system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.4
• /
• pp.268-277
• /
• 2009

This paper presents an DTC-PWM (Direct Torque Control-Pulse Width Modulation) of PMSM (Permanent Magnet Synchronous Motor). The proposed DTC-PWM method combines a conventional DTC and PWM approach for switching signal generation. The actual torque is estimated by the torque estimator in conventional method, but the switching signal is generated by PWM method according to the switching rules and torque error. A effective voltage vector and zero vector are used to generate the switching signals and asymmetric switching method is applied. A simple calculation of PWM without any complex determination of space vector can assure the constant switching frequency with an constant torque and flux. The proposed torque control scheme for PMSM is verified by experimental results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.10
• /
• pp.27-34
• /
• 2006

This paper proposes a new method of on-line estimation for rotor resistance of the induction motor in the indirect vector controlled drive, using artificial neural network (ANN). The back propagation algorithm is used for training of the neural networks. The error between the desired state variable of an induction motor and actual state variable of a neural network model is back propagated to adjust the weight of a neural network model, so that the actual state variable tracks the desired value. The performance of rotor resistance estimator and torque and flux responses of drive, together with these estimators, are investigated variations rotor resistance from their nominal values. The rotor resistance are estimated analytically, using the proposed ANN in a vector controlled induction motor drive.

• Convergence Security Journal
• /
• v.7 no.2
• /
• pp.1-8
• /
• 2007

Finite failure NHPP models presented in the literature exhibit either constant, monotonic increasing or monotonic decreasing failure occurrence rates per fault (intensity function). In this paper, intensity function of Goel-Okumoto model was reviewed, proposes Kappa (2) and the Burr distribution, which maked out efficiency application for software reliability. Algorithm to estimate the parameters used to maximum likelihood estimator and bisection method. For model determination and selection, explored goodness of fit (the error sum of squares) The methodology developed in this paper is exemplified with a software reliability real data set introduced by NTDS (Naval Tactical Data System)