• 콘크리트학회논문집
• /
• 제14권6호
• /
• pp.843-850
• /
• 2002

프리스트레스트 콘크리트 부재의 해석이론에서 텐던의 직선이동(linear transformation)은 텐던 배치에 대한 해석을 간략화시켜주는 장점이 있어 빈번히 다루어지고 있다. 본 논문은 그동안 간과되기 쉬웠던 직선이동에 내재된 근사화 및 그 영향을 밝히는데 중점을 두고 있으며, 주로 등가하중법(equivalent load method)을 통하여 직선이동의 이론을 분석하였다. 텐던이 이동하더라도 똑같은 등가하중 시스템이 산출되는 것을 직선이동으로 볼 경우, 기존의 등가하중법 고유의 내재된 가정은 그러한 직선이동의 원리가 성립하도록 하고 있으며, 반면 근사화가 포함되지 않은 엄밀한 의미의 등가하중 시스템에서는 그러한 원리가 성립하고 있지 않다 또한, 자체평형의 성질로부터 유도된 등가하중법을 직선이동에 적용하는 방안을 모색하였으며, 기존의 결과와 약간 다른 등가하중 시스템을 산출하였다. 논의를 확장하여 격납구조물 벽체 원환텐던(circumferential tendon)의 편심배치 문제를 직선이동의 관점에서 분석하였다.

• East Asian mathematical journal
• /
• 제34권5호
• /
• pp.615-621
• /
• 2018

Let R be a ring with the unity 1, and let e be an idempotent of R. In this paper, we discuss some symmetric property for the set $\{(a_1,a_2,{\cdots},a_n){\in}R^n:a_1a_2{\cdots}a_n=e\}$. We here investigate some properties of those rings with such a symmetric property for an arbitrary idempotent e; some of our results turn out to generalize some known results observed already when n = 2 and e = 0, 1 by several authors. We also focus especially on the case when n = 3 and e = 1. As consequences of our observation, we also give some equivalent conditions to the commutativity for some classes of rings, in terms of the symmetric property.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.792-793
• /
• 2008

This paper deals with the temperature calculation using equivalent thermal network for surface mounted permanent magnet synchronous motor(SPMSM) under the steady-state condition. In the equivalent thermal network, heat sources are generated from copper loss and iron loss. Heat transfer consists of conduction, convection and radiation. However, radiation is neglected in this paper because its effect is much smaller than others. Although the heat transfer coefficient in conduction use material property, heat transfer coefficient in convection is difficult to measure due to the atmosphere and ambient condition. Temperatures of each region in SPMSM are measured by thermocouple in operating condition and the thermal resistances of convection are calculated by kirchhoff's current law(KCL) and experimental result. In order to verify the validation and reliability of the proposed equivalent thermal network, temperature which is calculated other load condition is compared with experimental results. Accordingly, temperatures of each region in other SPMSMs will be easily predicted by the proposed equivalent thermal network.

• 조명전기설비학회논문지
• /
• 제20권6호
• /
• pp.81-86
• /
• 2006

회로 전송선 배선 시 신호선은 직선의 형태와 방향을 바꾸기 위한 구부러지는 형태를 가진다. 차동 신호선의 정확한 등가회로는 이러한 전송선 구조의 시 공간 영역에서의 신호적 특성과 인접 신호선들 간의 영향을 평가할 수 있게 해준다. 이를 위해 기존의 몇 몇 CAD Tool들이 등가 회로 모델과 그 파라미터 값들을 추출 해주기도 하지만, 이는 큰 연산량과 시간을 요구한다. 본 논문에서는 구부러진 차동 신호선의 등가회로를 모델링하기 위해 기본적 모델인 RLC-모델의 파라미터 값을 유전 알고리듬을 이용하여 추출하는 방법을 제시한다. 본 방법에 의해 더욱 빠르게 물리적 구조를 갖는 차동 신호선의 등가회로를 모델링 할 수 있다.

• 한국광학회지
• /
• 제9권4호
• /
• pp.251-257
• /
• 1998

등가렌즈 변환을 렌즈군의 변환으로 확장하였으며, 보다 일반화된 변환법을 개발하였다. 새로운 변환법은 두꺼운 렌즈계에서 바로 두꺼운 렌즈계로의 변환이 가능하다. 등가렌즈 변환을 통하여 얇은 렌즈계는 서로 다른 두께를 가지면서도 근축 광학적 특성이 같고 수차특성이 유사한 여러 개의 두꺼운 렌즈계로 변환 될 수 있다. 예로서 telephoto 렌즈계의 설계변경에 등가렌즈 변환을 적용하여 보았으며, 앞부분 렌즈군의 축상두께를 원설계의 75%로 축소하였다. 등가렌즈 변환을 통하여 얻어진 수정설계의 초점거리는 원설계와 동일하였으며, 축상두께만을 변경시킨 경우에 비하여 수차특성의 변화가 적음을 확인할 수 있었다.

• Journal of Mechanical Science and Technology
• /
• 제20권9호
• /
• pp.1323-1338
• /
• 2006

An analytical method to estimate the coupled frequencies of the circular plate submerged in fluid is developed using the finite Fourier-Bessel series expansion and Rayleigh-Ritz method. To verify the validity of the analytical method developed, finite element method is used and the frequency comparisons between them are found to be in good agreement. For the perforated plate submerged in fluid, it is almost impossible to develop a finite element model due to the necessity of the fine meshing of the plate and the fluid at the same time. This necessitates the use of solid plate with equivalent material properties. Unfortunately the effective elastic constants suggested by the ASME code are found to be not valid for the modal analysis. Therefore in this study the equivalent material properties of perforated plate are suggested by performing several finite element analyses with respect to the ligament efficiencies.

• 한국기계가공학회지
• /
• 제8권2호
• /
• pp.69-75
• /
• 2009

This study is analyzed by impact simulation according to material property at terminal case of hand phone. Maximum equivalent stress or strain at plastic is 40 times as great as that at magnesium alloy. And the next greatest stress or strain is shown at aluminium alloy. The value of maximum equivalent stress is shown as 6.5 Mpa in case of plastic, magnesium alloy and aluminium alloy. Maximum shear strain at plastic is 40 times as great as that at magnesium alloy. And the next greatest strain is shown at aluminium alloy. The value of deformation or strain at magnesium alloy and aluminium alloy is not different.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1995년도 추계학술발표회논문집(1)
• /
• pp.429-436
• /
• 1995

This paper describes a methodology for determination of representative CANDU feeder geometry and the pressure drops between inlet/outlet header and fuel channel in the primary loop. A code, MEDOC, was developed based on this methodology and helps perform a calculation of equivalent feeder geometry for a selected channel group on the basis of feeder geometry data (fluid volume, mass flow rate, loss factor) and given property data pressure, quality, density) at inlet/outlet header. The equivalent feeder geometry calculated based on this methodology will be useful fur the transient thermohydraulic analysis of the primary heat transport system for the CANDU heavy water-cooled pressure tube reactor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 C
• /
• pp.1057-1059
• /
• 1999

A procedure to develop dynamic equivalent systems of the KEPCO power system in the year 2010 was proposed, and 3 different equivalent systems in which the number of generators are 39, 30, and 19 were developed in this paper. The static and dynamic property of the reduced systems was verified by the comparison of time-domain simulation for the original system and the reduced systems.

• 산업경영시스템학회지
• /
• 제37권1호
• /
• pp.157-164
• /
• 2014

The usage of corrugated cardboard for packing material is increasing in these days because it is light and easy to manufacture packing boxes. However, the structure analysis of packing boxes, made of cardboard, is not well carried. The reason can be deduced that its mechanical properties for structure analysis are not well known. The cardboards are made different shapes with various types of raw materials that are paper-based compound. In addition, the cardboards are considered to be orthotropic material. This research finds mechanical properties of triple layered cardboard which is composed of outer liner and inner liner. The moduli of elasticity and of shear for liners are found from tension test and T-Peel test. The mechanical properties of the cardboard are calculated using the super position method and equivalent evaluation method.