• ETRI Journal
• /
• 제44권5호
• /
• pp.759-768
• /
• 2022

A novel energy harvesting technique that uses conducted electromagnetic interference as an energy source is presented. Conducted EMI generated from fluorescent light using a switched-mode power supply was measured and modeled as an equivalent voltage source. Two types of rectifier circuits-a bridge rectifier and a voltage doubler-were used as the harvesting devices for conducted EMI source. The matching networks were designed based on the equivalent model, and the harvested power was improved. The implemented energy harvester produces a regulated power over 68.9 mW and current over 15.1 mA while a regulated voltage can be selected between 3.3 V and 5 V. The proposed system shows the highest harvesting power indoor environment and can provide enough power for the Internet of Things devices.

• Journal of Electrochemical Science and Technology
• /
• 제13권2호
• /
• pp.167-176
• /
• 2022

Electrochemical impedance spectroscopy (EIS) is a unique non-destructive technique employed to analyze various devices in different energy storage applications. It characterizes materials and interfaces for their properties in heterogeneous systems employing equivalent circuits as models. So far, it has been used to analyze the performance of various photovoltaic cells, fuel cells, batteries, and other energy storage devices, through equivalent circuit designing. This review highlights the diverse applications of EIS in fuel cells and specific parameters affecting its performance. A particular emphasis has been laid on the challenges faced by this technique and their possible solutions.

• 전기의세계
• /
• 제25권5호
• /
• pp.75-78
• /
• 1976

The most difficult problem encountered in impulse test of transformer is the determination of exact fauly for coil layer short. This paper is to establish one of improved standards in the above case by means of wave form analysis, based on the equivalent circuits and experimental investigation. During the fault occurs, the local oscillation in fault circuit is applicable where as the reflection wave is utilized to the main circuit. The result current wave form at neutral impeadance point is similar to the wave form by impulse test and has the singular wave form respectively.

• 전자공학회논문지D
• /
• 제35D권1호
• /
• pp.49-58
• /
• 1998

In this paper, a new equivalent circuit model for quantum-well laser diode (LD) is proposed. The model includes carrier transport effects in the SCH region, and rprovides, in a stable and accurate manner, large-and small-signal responses of laser diode output power as function of injected currents. SPICE simulation was performed using the circuit model and results are presented for L-I characteristics, pulse and frequency responses under various conditions. It is expencted that the new equaivalent circuit model will find useful applications for designing and analyzing OEIC, LD driver circuits, and LD packaging.

• Journal of Power Electronics
• /
• 제8권3호
• /
• pp.239-247
• /
• 2008

This paper presents the design of 1 kW prototype high frequency link boost half bridge inverter-fed DC-DC power converters with bridge voltage-doublers suitable for small scale PEM fuel cell systems and associated control schemes. The operation principle of this converter is described using fuel cell modeling and some operating waveforms. The switching mode equivalent circuits are based on simulation results and a detailed circuit operation analysis at soft-switching conditions.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2002년도 학술대회논문집
• /
• pp.111-116
• /
• 2002

With the proliferation of nonlinear loads such as personal computers in an educational office building, high neutral harmonic currents have been observed. High neutral currents in three-phase four-wire distribution power systems can cause overloaded neutral conductors, overloaded transformers, voltage distortion, common mode noise, and malfuntion of protective equipment. On-site measurements of harmonic currents and voltages were made and the corresponding equivalent circuits was developed. The circuit model under study was simulated numerically and graphically through the use of the software MATLAB.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 연구회 합동 학술발표회 논문집
• /
• pp.49-54
• /
• 1998

This paper describes a simulation model to analyze the dynamic performance of Unified Power Flow Controller, which adjust flexibly the active and reactive power flow through the ac transmission line. The basic operation was analyzed in detail using equivalent circuits and the design of control system was developed using vector control method. A simulation model with EMTP code was conceived to evaluate the performance of the Unified power Flow Controller. The simulation results show that the developed simulation model is very effective to analyze the dynamic performance of the Unified Power Flow Controller.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.428-432
• /
• 1998

A passive energy recovery snubber for high-power-factor boost rectifier, in which the main switch is implemented with a MOSFET, is described in terms of the equivalent circuits that are operational during turn-on and turn-off sequences. The main switch combined with proposed snubber can be turned on with zero current and turned off at limited voltage stress. The high-power-factor boost rectifier with proposed snubber is implemented, and the experimental results are presented to confirm the validity of proposed snubber.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.254-258
• /
• 2001

This paper proposes a new induction heating system composed of a hyristor PWM rectifier with a resonant commutation circuit. The operation of proposed system as first analyzed by a theoretical approach with equivalent circuits. And its verification was performed by computer simulations with EMTP. The proposed system can provide a solution for the power factor problem of the existing high-power induction heating system. which uses the line-commutated thyristor bridge in rectifier side.

• 전자공학회논문지D
• /
• 제34D권6호
• /
• pp.1-10
• /
• 1997

By using the boundary element method, the cahracterization and the circuit modelling of the coplanar waveguide (CPW) discontinuities are performed bvia quasi-static approximation. The capacitive equivalent circuits are obtained by developing the 3-D boundary element method with collocation method. On the triangular patch, the numerical scheme employed the linear basis functions and the analytic solutions of the integrals on the singular points. The capacitive discontinuities of gaps, end-gaps, and open-ends are characterized and the results compared with the conductor backed coplanar waveguides.