• Journal of Korea Foundry Society
• /
• v.37 no.2
• /
• pp.38-44
• /
• 2017

Given that the conventional extrusion of high-strength Al alloys such as 7075 aluminum alloys is difficult due to their very low extrudability as compared to that of 6061 aluminum alloys, thixo-extrusion can be used to obtain a high-strength material easily at a lower extrusion pressure as compared to conventional extrusion. In this study, hot- and thixo-extruded 7075 aluminum alloys are prepared by a vertical forward extrusion process and their microstructures, hardness levels, and compressive properties are investigated. Hot-extruded alloy bars are assessed to obtain a microstructure elongated in the extrusion direction, whereas with thixo-extruded alloy bars, it was possible to obtain a microstructure having fine and equiaxed grains by dynamic recrystallization. The resulting isotropy and improved formability at the hot deformation temperature of the thixo-extruded alloy were attributed to the fine and equiaxed grains formed by the thixo-extrusion process.

• Corrosion Science and Technology
• /
• v.9 no.3
• /
• pp.109-115
• /
• 2010

Interstitial-free (IF) steels are widely used for car body material. However, a few types of streaky mark defect are commonly found on hot dip galvannealed (GA) IF steel sheets. In the present study, both the phase structure of a streaky mark defect and the microstructure of the substrate just below it were characterized by optical microscopy (OM) and scanning electron microscopy (SEM). It was found that the bright streaky mark area was composed of ${\delta}$ phase while the dark normal area was full of craters. More than half of the grains at the uppermost surface of the substrate just below the streaky mark defect are unrecrystallized grains which could result from lower finish rolling temperature during hot rolling and be kept stable during the annealing process, while almost all the grains in the normal area are equiaxed grains. In order to confirm the effect of the unrecrystallized grains on the coating morphology, hot dip galvannealing simulation experiments were carried out in IWATANI HDPS. It is proved that the unrecrystallized grains accelerate the Fe-Zn reaction rate during galvannealing and result in a flatter coating surface and an even coating thickness. Finally, a formation mechanism of the streaky mark defect on the hot dip galvannealed IF steel sheet was discussed.

• Journal of the Korean Ceramic Society
• /
• v.42 no.8 s.279
• /
• pp.525-531
• /
• 2005

Tailoring the microstructure and the composition of silicon nitride ceramics can have profound effects on their properties. Here it is shown that the grain growth behavior, in particular its anisotropy, is a function of the specific additives, which allow one to tune the microstructure from one consisting of more equiaxed grains to one with very elongated grains. Recent studies are discussed that provide an understanding of the atomic level processes by which these additives influence grain shapes. Next the microstructural (and compositional) parameters are discussed that can be used to modify the thermal conductivity, as well as fracture toughness of silicon nitride ceramics. As a result of the open <0001> channels in $\beta-Si_3N_4$, the c-axis conductivity can be exceptionally high. Thus, the formation of elongated c-axis grains, particularly when aligned can result in conductivity values approaching those of AlN ceramics. In addition, the controlled formation of elongated grains can also be used to significantly enhance the fracture toughness. At the same time, both properties are shown to be affected by the composition of the densification additives. Utilizing such understanding, one will be able to tailor the ceramics to achieve the properties desired for specific applications.

• Transactions of Materials Processing
• /
• v.13 no.5
• /
• pp.449-454
• /
• 2004

The annealing behavior of a 5083 Al alloy deformed at cryogenic temperature was investigated, focusing on the evolution of microstructures and mechanical properties. Especially, the effects of annealing temperature, $150~300^{\circ}C$, and time, 3∼60min., on microstructures and mechanical properties of the sheets received 85% reduction at cryogenic temperature were investigated. The optimization of the annealing conditions resulted in a mixture of equiaxed grains and elongated subgrains, exhibiting a good combination of uniform elongation and high strength.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.281-284
• /
• 2003

The microstructural changes of Al-Zn-Mg-Cu alloy containing Sc during hot extrusion and post heat treatment is investigated. Two kinds of Al-Sc alloys with different alloying elements (B1, B2) are hot extruded to make I-shape bars at 380$^{\circ}C$, then the bars are solution treated at 480$^{\circ}C$ for 2hrs followed by artificial aging at 120$^{\circ}C$ for 24hrs. The interior microstructure of as extruded bar consists of elongated grains, however, fine equiaxed grains are mainly observed around surface. The microstructural gradient suggests that different restoration process can proceed during the hot extrusion. For B1 and B2, different grain growth behaviors are found around the surface during the post heat treatment. Rapid grain growth behavior around the surface is discussed related with the crystallographic orientation of the grain.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.163-167
• /
• 2003

The large deformation at cryogenic temperature would be one of the effective methods to produce large bulk UFG materials. The effects of annealing temperature 150∼300$^{\circ}C$, on microstructure and mechanical properties of the sheets received 85% reduction at cryogenic temperature were investigated. In comparison with those at room temperature. Annealing of 5083 Al alloy deformed 85%, at 200$^{\circ}C$ for an hour, results in the considerable increase of tensile elongation without the great loss of strength and the occurrence of equiaxed grains less than 300nm in diameter.

• Proceedings of the KWS Conference
• /
• 2003.11a
• /
• pp.253-255
• /
• 2003

Commercially pure 1050 aluminum alloy with ultra-fine grain sizes was produced by a friction stir process. The maximum temperature in the friction stir processed zone decreased almost linearly with the tool rotation speed. In the friction stir processed zone, dislocation density was very low and fine equiaxed grains were observed. The grain size decreased with tool rotation speed. It is noteworthy that, for 560 rpm, a grain size decreased to even the submicron level with only the single pass of friction stir process. These fine grains resulted in improvement in hardness of the friction stir processed zone.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.621-627
• /
• 1996

$SrBi_{2x}TaO_9$ ferroelectric thin films were prepared on platinized silicon substrates using MOD proces, and crystallization behavior of the films was investigated with variation of the annealing temperature and Bi content x. Crystalline phase of bismuth layered perovskite structure was formed even by baking the films at $800^{\circ}C$ for 5 minutes in air, and was not changed by annealing at temperatures raning from $700^{\circ}C$ to $900^{\circ}C$ for 1 hour in oxygen ambient. When $SrBi_{2x}TaO_9$ thin films ($0.8\lex\ie1.6$) were annealed at $800^{\circ}C$, Preferred orientation of the films along c-axis was observed with $x\ge1.2$. With increasing Bi content x, surface morphology of the films was changed from equiaxed grains to elongated grains.

• Transactions of Materials Processing
• /
• v.13 no.2
• /
• pp.137-141
• /
• 2004

The large deformation at cryogenic temperature is expected as one of the effective methods to produce large bulk ultrafine grained materials. The effects of annealing temperature, 150∼$300^{\circ}C$, on microstructures and mechanical properties of the sheets received 85% reduction at cryogenic temperature were investigated, in comparison with those at room temperature. Annealing of 5083 Al alloy deformed 85%, at $200^{\circ}C$ for an hour,. resulted in the considerable increase of tensile elongation without the great loss of strength and the occurrence of equiaxed grains less than 300nm in diameter.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.05a
• /
• pp.177-180
• /
• 2002

The effects of pressing temperatures on the formability and the microstructural evolution during equal channel angular pressing (ECAP) of lamellar Ti-6Al-4V alloy were investigated in this study. ECAP above isothermally 600$^{\circ}C$ was successful without producing any noticeable segments at the specimen surfaces after a single pass of pressing. After 4 passes of ECA pressing, lamellar microstructures were significantly refined revealing equiaxed grains of 0.3$\mu\textrm{m}$ in diameter consisting of high angle grain boundaries. Also these ultrafine grains were relatively stable with little grain growth when annealed up to 600$^{\circ}C$ for 1hour.