• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.4C
• /
• pp.129-137
• /
• 2012

With the increase in infrastructure needs and tunnel construction, more complicated geometries have come to light, especially in cross tunnel design and construction. The major factors to influence existing tunnels are spacing between tunnels, relative position, size of the new tunnel, construction techniques, topographic and geologic conditions, structure, and alternative construction. In this study, settlement from an excavation for a new tunnel near an existing tunnel, settlement from a change in position of the new tunnel relative to an existing tunnel, and the distribution of deformations of the existing tunnel as a result of excavating the cross-location are analyzed through laboratory model tests. As the results, in condition of the new tunnels go through below the existing tunnel, not only analysed through the standard of the diameter of the tunnel, so it would need to set up to strengthen the field within each side of the 1D, but also determined the part of the cross in the existing and the new tunnel, should implement the reinforcement from the part of new tunnel to the existing tunneling influence of excavation.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.2
• /
• pp.193-202
• /
• 2018

This paper proposed a crack spacing calculation formulation which is an important parameter for calculating the crack width, that is the main factor for verification of serviceability limit states and durability performance evaluation of reinforced concrete members. The basic equation of average crack spacing is derived by considering the bond characteristics which is the governing equation for the analysis of cracking behavior in reinforced concrete members. In order to consider the effect of the cover thickness and concrete compressive strength, the crack spacing measured in 124 direct tensile tests performed by several researchers was analyzed and each coefficient was proposed. And, correlation analysis was performed from 80 specimen data where the maximum and average crack spacing were simultaneously measured, and a correlation coefficient that can easily predict the maximum crack spacing from the average crack spacing was proposed. The results of the proposed average crack spacing equation and maximum crack spacing correlation were compared with those current design code specification. The comparisons of proposed equations and the Korean design codes show that the proposed formulation for the average crack spacing and the maximum crack spacing improves the accuracy and reliability of prediction compared to the corresponding provisions of the Korean Concrete Structural Design Code and Korean Highway Bridge Design Code (Limit States Design).

• Journal of the Society of Disaster Information
• /
• v.16 no.1
• /
• pp.60-69
• /
• 2020

Purpose: Cavity growth process monitoring is to periodically monitor changes in common size and topography for general and observational grades to predict the rate of common growth. The purpose of this study is to establish a systematic cavity management plan by evaluating the general and observational class community in a non-destructive method. Method: Using GPR exploration equipment, the acquired surface image and the surrounding status image are analyzed in the GPR probe radargram in depth, profile, and cross section of the location. The exact location is selected using the distance and surrounding markings shown on the road surface of the initial detection cavity, and the test cavity is analyzed by calling the radar at the corresponding location. Result: As a result of monitoring tests conducted at a cavity 30 sites of general and observation grade, nine sites have been recovered. Changes in scale were seen in 21 cavity locations, and changes in size and grade occurred in 13 locations. Conclusion: The under road cavity is caused by various causes such as damage to the burial site, poor construction, soil leakage caused by groundwater leakage, waste and ground vibration. Among them, indirect factors could infer the effects of groundwater and localized rainfall.

• Toxicological Research
• /
• v.33 no.3
• /
• pp.225-231
• /
• 2017

National reference standards (NRSs) for biologics are established through potency estimation by a multi-center joint study of standard materials used in the approval process for national lot release and quality control of vaccines, blood products, and other biologics. In this study, a stability evaluation was conducted to determine whether the potency of NRSs for six blood products was being maintained at a consistent level in Korea. The present study conducted real-time stability tests via in-vivo/in-vitro bioassay on NRSs for blood coagulation factor VIII concentrate (2nd standard), antithrombin concentrate, prekallikrein activator, anti-hepatitis B immunoglobulin, blood coagulation factor IX concentrate, and anti-tetanus human immunoglobulin, as well as a trend analysis using cumulative annual results. The real-time stability test results showed that the mean potency of six NRSs was all within the control limit. In the trend analysis, the potency of NRS for blood coagulation factor VIII concentrate (2nd standard) showed a decreasing trend, while the potency of all other products had been stably maintained. The present study confirmed that the mean potency of NRSs for six blood products had been stably maintained in Korea. The findings of the present study establish a foundation that can ensure the quality of NRSs for biologics in Korea, and it is expected to make a major contribution to the supply of high-quality biologics.

• Toxicological Research
• /
• v.34 no.3
• /
• pp.191-197
• /
• 2018

In 2015, a candidate for the second national reference standard (NRS) of Gloydius snake venom was produced to replace the first NRS of Gloydius snake venom. In the present study, the potencies of the candidate were determined by a collaborative study, and the qualification of the candidate was estimated. The potencies of the candidate were determined by measuring the murine lethal titers and lapine hemorrhagic titers of venom against the regional working reference standard (RWRS) for antivenom using the methods described in the previous report for the first NRS of Gloydius snake venom. Three Korean facilities contributed data from a total of 30 independent assays. Subsequently, two foreign national control research laboratories contributed to this collaborative study. The results were calculated using the Reed-Muench method for lethality and determined using a mixed-effects model for hemorrhage. The general common potencies of the lethal and hemorrhagic titers were obtained from the results of the 30 tests performed at three Korean facilities. The results are expressed in micrograms for 1 test dose (TD) with a 95% confidence interval as follows: a lethal titer of $90.13{\mu}g/TD$ (95% confidence interval = $87.39{\sim}92.86{\mu}g$) and a hemorrhagic titer of $10.80{\mu}g/TD$ (95% confidence interval = $10.46{\sim}11.14{\mu}g$). In addition, the candidate preparation showed good quality evaluation according to the results of the quality estimation of the candidate and is judged to be suitable to serve as the Korean NRS for snake venom. In conclusion, the second NRS of Gloydius snake venom was established in this study and will be used for national quality control, including a national lot release test of Korean antivenom products.

• Korean Journal of Veterinary Research
• /
• v.46 no.4
• /
• pp.295-304
• /
• 2006

Residual materials such as veterinary drugs, environmental contaminants, and pesticides are affecting food safety. High resolution techniques and quality controls are needed to analyze these materials from part per million to part per trillion quantities in food. In order to achieve quality results, standardized methods and techniques are required. Our laboratories were prepared to obtain a certificate of accreditation for ISO/IEC 17025 in the analytical criteria of animal drugs, dioxins, pesticides, and heavy metals. ISO together with IEC has built a strategic partnership with the World Trade Organization with the common goal of promoting a free and fair global trading system. ISO collaborates with the United Nations Organization and its specialized agencies and commissions, particularly those involved in the harmonization of regulations and public policies including the World Health Organization and CODEX Alimentarius for food safety measurement, management and traceability. Our goal was to have high quality analysts, proper analytical methods, good laboratory facilities, and safety systems within guidelines of ISO/IEC 17025. All staff members took requirement exams. We applied proficiency tests in the analysis of veterinary drugs (nitrofuran metabolites, sulfonamide and tetracyclines), dioxins, organophosphorus pesticides, and heavy metals (Cd, Pb, As) to the Food Analysis Performance Assessment Scheme (FAPAS) at Central Science Laboratory, Department for Environment Food and Rural Affairs (DEFRA), England. The results were very satisfactory. All documents were prepared, including system management, laboratory management, standard operational procedures for testing, reporting, and more. The criteria encompassed the requirements of ISO/IEC 17025:1999. Finally, the Korea Laboratory Accreditation Scheme (KOLAS) accredited our testing laboratories in accordance with the provisions of Article 23 of the National Standards Act. The accreditation will give us the benefit of becoming a regional reference laboratory in Asia.

• Fire Science and Engineering
• /
• v.31 no.2
• /
• pp.17-23
• /
• 2017

The test methods using convection (flame) and radiation heat sources were compared to evaluate the thermal protective performance of the firefighter's protective clothing. In particular, the influence of the outer shell, mid-layer, and lining constituting the firefighter's protective clothing on the thermal protective performance was compared for convection and radiation heat sources. Tests for the thermal protective performance were carried out according to KS K ISO 9151 (convection), KS K ISO 6942 (radiation), and KS K ISO 17492 (convection and radiation). When tested under the same incident heat flux conditions ($80kW/m^2$), the heat transfer index ($t_{12}$ and $t_{24}$) for the radiation heat source was higher than that for the convection heat source. This means that radiation has a lesser effect than convection. For the convection heat source, the lining had the greatest effect on the thermal protective performance, followed by the mid-layer and the outer shell. On the other hand, for the radiation heat source, the effect on the thermal protective performance was great in the order of lining, outer shell, and mid-layer. Convection and radiation have fundamentally different mechanisms of heat transfer, and different heat sources can lead to different thermal protective performance results depending on the material composition. Therefore, to evaluate the thermal protective performance of the firefighter's protective clothing, it is important to test not only the convection heat source, but also the radiation heat source.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2009.06a
• /
• pp.84-85
• /
• 2009

New approaches for detecting, preventing and remedying environmental damage are important for protection of the environment. Procedures must be developed and implemented to reduce the amount of waste produced in chemical processes, to detect the presence and/or concentration of contaminants and decontaminate fouled environments. Contamination can be classified into three general types: airborne, surface and structural. The most dangerous type is airborne contamination, because of the opportunity for inhalation and ingestion. The second most dangerous type is surface contamination. Surface contamination can be transferred to workers by casual contact and if disturbed can easily be made airborne. The decontamination of the surface in the nuclear facilities has been widely studied with particular emphasis on small and large surfaces. The amount of wastes being produced during decommissioning of nuclear facilities is much higher than the total wastes cumulated during operation. And, the process of decommissioning has a strong possibility of personal's exposure and emission to environment of the radioactive contaminants, requiring through monitoring and estimation of radiation and radioactivity. So, it is important to monitor the radioactive contamination level of the nuclear facilities for the determination of the decontamination method, the establishment of the decommissioning planning, and the worker's safety. But it is very difficult to measure the surface contamination of the floor and wall in the highly contaminated facilities. In this study, the poly(styrene-ethyl acrylate) [poly(St-EA)] core-shell composite polymer for measurement of the radioactive contamination was synthesized by the method of emulsion polymerization. The morphology of the poly(St-EA) composite emulsion particle was core-shell structure, with polystyrene (PS)as the core and poly(ethyl acrylate) (PEA) as the shell. Core-shell polymers of styrene (St)/ethyl acrylate (EA) pair were prepared by sequential emulsion polymerization in the presence of sodium dodecyl sulfate (SOS) as an emulsifier using ammonium persulfate (APS) as an initiator. The polymer was made by impregnating organic scintillators, 2,5-diphenyloxazole (PPO) and 1,4-bis[5-phenyl-2-oxazol]benzene (POPOP). Related tests and analysis confirmed the success in synthesis of composite polymer. The products are characterized by IT-IR spectroscopy, TGA that were used, respectively, to show the structure, the thermal stability of the prepared polymer. Two-phase particles with a core-shell structure were obtained in experiments where the estimated glass transition temperature and the morphologies of emulsion particles. Radiation pollution level the detection about under using examined the beta rays. The morphology of the poly(St-EA) composite polymer synthesized by the method of emulsion polymerization was a core-shell structure, as shown in Fig. 1. Core-shell materials consist of a core structural domain covered by a shell domain. Clearly, the entire surface of PS core was covered by PEA. The inner region was a PS core and the outer region was a PEA shell. The particle size distribution showed similar in the range 350-360 nm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.4
• /
• pp.1747-1754
• /
• 2013

We evaluate the impact of near work has on myopia and how they differ across generation. The study subjects were 201(83 males and 118 females) adults who live in Cheongju and Daejeon. Myopia was defined as more than or equal to (-)2.50D. The subjects were divided myopic and control group. The surveys and eye tests that are related to near work and refractive error were conducted and the relationship between the degree of myopia and near work was investigated. Then, the groups were divided into people in their 20s and 30s and the comparisons were made again. The survey results showed significant differences between myopic and control groups that depended on: hours spent in school and outdoor activities during high school period, degree of refractive error caused by level of exercises during the junior high school and high school years, refractive error based on the type of high schools, also hours spent in school and outdoor activities. When the same question was done on the group in their 20s and 30s, there was a different outcome in trends between the groups and refractive error depending on whether they exercised. The degree of near work is one of the environmental risk factors that affect myopia and must be considered when studying myopic progression. However, when discussing specific behavioral patterns in relations to myopia prevention, culture and visual environment of a given generation must also be considered.

• Journal of Preventive Medicine and Public Health
• /
• v.40 no.6
• /
• pp.505-511
• /
• 2007

Objectives : While cervical cancer is one of the leading cancers among women worldwide, there are a number of effective early detection tests available. However, the participation rates in cervical cancer screening among Korean women remain low. After the nationwide efforts in 1988 and thereafter to encourage participation in cervical cancer screening, few studies have investigated the effects of socioeconomic inequality on participation in cervical cancer screening. The purpose of this study was to investigate 1) the level of socioeconomic disparities in receiving cervical cancer screening by age group and 2) if there was an improvement in reducing these disparities between 1995 and 2001. Methods : Using data from the Korean National Health Status, Health Behavior and Belief Survey in 1995, the Korean National Health and Nutrition Examination Surveys from 1998 and 2001 (sample sizes of 2,297, 3,738, and 3,283), age-standardized participation rates were calculated according to education level, equivalized household income, and job status. Odds ratios and the relative inequality index (RII) were also calculated after controlling for age. Results : Women with lower education levels were less likely to attend the screening test, and the disparities by education level were most pronounced among women aged 60 years and older. The RIIs among women 60 years and older were 3.64, 4.46, and 8.64 in 1995, 1998, and 2001, respectively. Higher rates of participation were reported among those in the highest income category, which was more notable among the middle aged women (40s and 50s). An inconsistent trend in the rate of participation in cervical cancer screening by occupational level was found. Conclusions : Indicators of socioeconomic position seem to have varying impacts on the inequalities in the rates of participation in cervical cancer screening according to age group. These results demonstrate the need for more aggressive and age-based interventions and policy programs to eliminate the remaining inequalities.