• Journal of the Korean Association of Geographic Information Studies
• /
• v.13 no.1
• /
• pp.114-127
• /
• 2010

The purpose of this study is to find out cold and fresh air producing areas using climate-ecological functions in Changwon city, Gyeongsangnam-do, South Korea. The evaluation of climate-ecological functions were composed of the six factors: patch size with cold air generation and inflow functions, farmland and grassland ratio, mean slope degree, cross section types, mean slope length and roughness of bottom in valley. The analysis results of each evaluation factor in the study area were divided into 5 grades according to the capacity of cold air generation. The first-grade area with the highest factor values for cold air generation was take up 3.51% of the total study area, second grade was 13.48%, third grade was 31.65%, fourth grade was 27.28%, and fifth grade was 24.09%. According to the spatial distribution of cold air producing areas, the valleys around Mt. Bongnim, Changwon tunnel, and Anmin tunnel had higher evaluation grade. It will require the future research to establish the climate-ecological conservation areas and to construct the wind corridor based on the long-term microclimatic monitoring.

• Journal of the Korean GEO-environmental Society
• /
• v.4 no.4
• /
• pp.45-51
• /
• 2003

Grouting materials in rock is grouted as vein type along the fault surface by the other way for soil and allow a change of characteristics in rock faults as a result of that. Therefore the deformation characteristics of rock faults after grouting differ as a direction and characteristic of grouted fault and stress condition of field rock. Thereby it must be analyzed the effect for deformation of rock according to characteristics of rock faults and characteristics of grouting materials to accurately evaluate the reinforced effect by grouting. But grouting method used in field until present depends on experience of workers, and inspection for those effects are evaluated by measurement of elastic wave velocity, permeability tests and etc. in field. In this study, it was investigated that the effects for shear characteristics of maximum shear strength, residual shear strength and etc. by comparison and analysis of test results which were worked by direct shear tests of rock faults with changing a type of grouting materials and the grouting depth(t) for average width(a) of fault surface roughness when OPC(Ordinary Portland Cement) and Micro cement was grouted in fault surface of field rock to evaluate characteristicsof the shear deformation for rock fault surface of dam by grouting.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.12
• /
• pp.23-30
• /
• 2013

Bearing capacity of pile is governed by only skin friction in frozen ground condition, while it is generally governed both by skin friction and end bearing capacity in typically unfrozen ground condition. Skin friction force, which arises from the interaction between pile and frozen soils, is defined as adfreeze bond strength, and adfreeze bond strength is one of the most important key parameters for design of pile in frozen soils. Many studies have been carried out in order to analyze adfreeze bond strength characteristics over the last fifty years. However, many studies for adfreeze bond strength have been conducted with limited circumstances, since adfreeze bond strength is sensitively affected by various influence factors such as intrinsic material properties, pile surface roughness, and externally imposed testing conditions. In this study, direct shear test is carried out inside of large-scaled freezing chamber in order to analyze the adfreeze bond strength characteristics with varying freezing temperature and normal stress. Also, the relationship between adfreeze bond strength and shear strength of the frozen soil obtained from previous study was analyzed. The coefficient of adfreeze bond strength was evaluated in order to predict adfreeze bond strength based on shear strength, and coefficients suggested from this and previous studies were compared.

• Economic and Environmental Geology
• /
• v.39 no.6 s.181
• /
• pp.719-738
• /
• 2006

Simrad EM950 multibeam data and surficial sediment grab samples were acquired to correlate backscatter strength with surficial sediment properties in the eastern Yellow Sea which tidal sand ridges are dominantly developed. The study area is divided into the western sand ridge zone characterized by well sorted, fine sandy sediment, and the eastern non-sand ridge zone characterized by poorly sorted, medium sand with some gravels and shell fragments. In spite of minor difference in grain size between two zones, the variations of backscatter strength between two zones are distinct. Multibeam backscatter strength of study area shows good correlation with the grain size of surface sediment as well as the carbonate contents. High occurrence of carbonate shell fragments can increase grain size and bottom roughness. The dominance of higher backscatter strength in the eastern non-sand ridge zone may reflect the effects of coarse grain size and high shell fragments contents.

• Journal of the Korean Geosynthetics Society
• /
• v.17 no.2
• /
• pp.33-40
• /
• 2018

Characteristics of interface friction between cohesionless soils and geotechnical structure surfaces play an important role in the analysis of earth load and resistance on the structure. In general, geotechnical structures are mainly composed of either steel or concrete, and their surface roughnesses with respect to soil particle sizes influence the interface characteristics between soils and the structures. Accurate assessment of the interface friction characteristics between soils and structures is important to ensure the safety of geotechnical structures, such as mechanically stabilized earth walls reinforced with inextensible reinforcements, piles embedded into soils, retaining wall backfilled with soils. In this study, based on the database of high quality interface friction tests between frictional soils and solid surfaces from literature, equation representing peak interface friction angle is proposed. The influential factors of the peak interface friction angle are relative roughness between soil and solid surface, relative density of frictional soil, and residual (constant volume) interface friction angle. Futhermore, for the developed equation of the interface friction angle, its uncertainty was assessed statistically based on Goodness-of-fit test results.

• Ecology and Resilient Infrastructure
• /
• v.5 no.1
• /
• pp.25-34
• /
• 2018

This study presents prediction and historical analysis of the long-term bed elevation change in the Mankyung-gang River. The study area is a 25 km long reach including middle and lower courses of the Mankyung-gang River. HEC-RAS program was used for numerical predictions, and values of roughness coefficients were calibrated. Then, predictions were made in the two periods, seven years from 1986 to 1993 and twelve years from 1993 to 2005. Simulation results were compared with two sets of measured data for bed elevations. Four sediment transport formulas, namely MPM's, Toffaleti's, MPM-Toffaleti's, and Yang's formula, were tested. Simulation results showed that none of the four sediment transport formulas predicted the bed elevation change in the period of 1986 - 1993. This is related to the fact that dredging work was performed in the upstream reach in the period of 1986 - 1993, and sediment was deposited in this part severely later. However, it was found that MPM-Toffaleti's formula predicted properly the bed elevation change for the period of 1993 - 2005.

• Economic and Environmental Geology
• /
• v.42 no.4
• /
• pp.357-366
• /
• 2009

Since weathering weakens the rock fabric and exaggerates any structural weakness, it affects mechanical properties as well as physical and chemical properties of rock. Weathering leads to a decrease in density, strength, friction angle and cohesion, and subsequently it affects negatively on the stability of rock slope. The purpose of the study is to investigate the changes of the rock slope stability caused by discontinuities which have different weathering grades. For that, the discontinuity samples which are divided into two different weathering grades are obtained from the field and tested their mechanical properties such as JCS, JRC and residual friction angle. In order to evaluate the effects on the stability of slope due to weathering, the deterministic analysis is carried out. That is, the factors of safety for planar failure are calculated for rock masses which have two different weathering grades, such as fresh and weathered rock mass. However, since the JRC and friction angle values are widely scattered and the deterministic analysis cannot consider the variation, the factors of safety cannot represent properly the stability of the rock slope. Therefore, the probabilistic analysis has been used to consider the scattered values. In the deterministic analysis, the factors of safety for the fresh discontinuity and weathered discontinuity are 1.25 and 1.0, respectively. The results indicate the fresh discontinuities are stable for planar failure and the weathered discontinuities are marginally stable. However, the probabilities of failure for the fresh discontinuity and weathered discontinuity are 25.6% and 45.9%, respectively. This shows that both discontinuities are analyzed as unstable in the probabilistic analysis.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.775-784
• /
• 2009

Weathered foliation could act as a critical failure plane because this type of plane tend to have low roughness and long extensions. A big constructed slope at $\bigcirc\bigcirc$ road construction site was failed due to the block movement along a fault zone which is parallel to foliation. Tectonic activity reactivated a fault zone parallel to foliation, and the fault clay within the shear zone metamorphosed retrogressively to chrolite. The failed block moved when the block weigh lost the balancing with the resisting force of the retrogressively metamorphosed chrolite. Evaluating the three dimensional distribution of the foliation was critical for establishing a plan for the stabilization of the slope. For this purpose, 10 boreholes were drilled as a lattice distribution, and the BIPS analyses are performed at each boreholes. The fractures measured in the boreholes are projected into 15 cross sections and their distributions are analysed, using Fracjection software. The projection analyse show that the strike of the foliation gets dipper towards left side of the slope. This geometry indicates that there are more failure block geometry at left side of the slope. Potential failure planes are searched using the projection method, and these information are provided for further support design.

• Journal of Korea Water Resources Association
• /
• v.38 no.11
• /
• pp.917-925
• /
• 2005

LSIV (Large Scale Image Velcocimetry) Is one of the image-based velocity measurement techniques. Since it measures surface velocities, it gives simple and inexpensive way to measure velocity, compared to other methods. Because of these advantages, there have been many studies to apply LSIV to the river discharge measurement in the field. Measuring the discharge by using LSIV requires a method which converts a surface velocity to a mean velocity In the present study, experiments and analysis of vortical velocity profile of open-channel flow in various conditions were performed to develop methods which estimate a mean velocity from a surface velocity. The result of this experiment reveals that velocity-dip phenomena occur at free-surface layer in open channel flow and Froude number affects more than bed roughness does. Two methods for estimating the mean velocity were proposed. One is to correct the wake law's profiles by using the difference of surface velocity from the mean velocity, and the other is to use the ratio of mean and surface velocities. The result of applying these methods in an experiment shows that they are quite accurate having an error of approximately $6\%$ only.

• Journal of Korea Water Resources Association
• /
• v.50 no.8
• /
• pp.521-535
• /
• 2017

Acoustic Doppler Current Profilers (ADCPs) have been widely utilized for assessing streamflow discharge, yet few comprehensive studies were conducted to evaluate discharge uncertainty in consideration of individual uncertainty components. It could be mostly because it was not easy to determine which uncertainty framework can be appropriate to rigorously analyze streamflow discharge driven by ADCPs. In this regard, considerable efforts have been made by scientific and engineering societies to develop a standardized theoretical framework for uncertainty analysis in hydrometry. One of the well-established UA methodology based on sound statistical and engineering concepts is Guide to the Expression of Uncertainty Measurement (GUM) adopted widely by various scientific and research communities. This research fundamentally adapted the GUM framework to assess individual uncertainty components of ADCP discharge measurements, and subsequently provided results of a customized experiment in a controllable real-scale artificial river channel. We focused particularly upon sensitivities of uncertainty components in the GUM framework driven by ADCPs direct measurements such as depths, edge distance, submerged depth, velocity gap, sampling time, repeatability, bed roughness and so on. Section-by-Section method for ADCP discharge measurement was applied for uncertainty analysis for this study. All of measurements were carefully compared with data using other instrumentations such as ADV to evaluate individual uncertainty components.