• Journal of the Korean Society of Safety
• /
• v.32 no.3
• /
• pp.8-14
• /
• 2017

This study examined the combustion and thermal characteristics of imported woods for building materials in Korea. Wooden specimens were confirmed by a cone calorimeter according to the KS F ISO 5660-1 standard. The combustion properties of the wooden specimens were measured in terms of the heat release rate (HRR), total heat released (THR), mass lose rate (MLR), and ignition time (time to ignition; TTI). The optical microscope was used for determine the anatomical characteristics of wood pit and structure. Also, the thermal properties were measured by thermogravimetric analysis (TGA) to determine the thermal stability of wooden specimens. The result of this experiment would be useful for fundamentals of guiding the combustion properties and thermal stability using wood application.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.4
• /
• pp.413-421
• /
• 2018

The pyroshocks can cause failure of electronics devices and structures. Metal-metal impact methods are utilized to simulate mechanical pyroshock, and to adjust the knee frquency of the SRS(Shock Response Spectrum) through resonant structures. In this paper, the major parameters of pyroshock simulation device which affect the SRS were examined. Through the Hertzian contact law and the modal characteristics of the resonant bar, it was found that the SRS is affected by the length and mass of a bar and various impact conditions such as velocity and mass of impactor. The characteristics due to the geometric parameters of a resonant bar was analyzed by performing FEA and also the resonant bar was designed and fabricated. Through the pyroshock simulation test, the characteristics of SRS due to the variation of impact parameters were examined.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.709-718
• /
• 2015

Traditional transmission planning usually caters for rated wind power output. Due to the low occurrence probability of nominal capacity of wind power and huge investment in transmission, these planning methods will leads to low utilization rates of transmission lines and poor economic efficiency. This paper provides a novel transmission expansion planning method for integrating large-scale wind power. The wind power distribution characteristics of large-scale wind power output and its impact on transmission planning are analyzed. Based on the wind power distribution characteristics, this paper proposes a flexible and economic transmission planning model which saves substantial transmission investment through spilling a small amount of peak output of wind power. A methodology based on Benders decomposition is used to solve the model. The applicability and effectiveness of the model and algorithm are verified through a numerical case.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.2
• /
• pp.69-74
• /
• 1999

This paper presents about a example of circuit design and characteristics of proposed circuit in the case of adopted the high frequency resonant Inverter of SEPP type using ZVS(Zero-Voltage-Switching) to the Induction heating load. The soft switching technology known as ZVS is used to reduce turn on and off loss at switching. Also, this paper realizes quantitative circuit analysis which has change the equivalent of Induction heating load to the electric circuit. According to the calculated characteristics value, a method of the circuit designs and operation characteristics of the Inverter is proposed. In addition, this paper proves the propriety of theoretical analysis through the experiment. The proposed inverter shows it can be practically used as power source system for induction heating Jar etc.

• Journal of Information Display
• /
• v.2 no.4
• /
• pp.29-33
• /
• 2001

The luminance and discharge characteristics of an AC PDP may be significantly affected by a small amount of impurity gas in working gas. Impurity gases such as $O_2$, O , C and $H_2$ can be mixed in the manufacturing and lor discharge processes. In this paper, a small amount of impurity gas in AC PDP are introduced intertimally and the relationship between the amount of impurity gas and the luminance/discharge characteristics are investigated. The luminous efficiency decreased seriously with the increase in the partial pressure of impurity gases, especially in $H_2$, $O_2$ and $CO_2$, Under the condition of the impurity gas ratio of 2x $10^{-3}$ for Ar, $N_2$, $H_2$, $CO_2$ and $O_2$, the luminous efficiency decreased to about 8%, 8%, 32%, 36% and 50%, respectively.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1818-1820
• /
• 2003

In this study, we developed friendly-environment device through various applications of pulse power system and studied research about pulse energy transfer characteristics. We have studied the mutual relation between characteristics of the load impedance and consumed power of the pulse power system. The consumed power means electrical power from the wall plug. For changing the load impedance, we could change elecrode length. As results, we can get electrical characteristics between pulse generator and load. When the pulse energy was triggered the microbes, caused waste water, they were almost removed in the waste water.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.2
• /
• pp.257-262
• /
• 2007

In this paper the experiments of breakdown characteristics by temperature change of $SF_6$ gas($GSF_6$), and $SF_6$ liquid ($LSF_6$) in model GIS (Gas Insulated Switchgear) are described. From the experiment's results, the breakdown characteristics classify the vapor stage of $SF_6$ according to Paschen's law, in which the gas & liquid coexisted stage of voltage value increases, resulting in much deviation and the breakdown of voltage ($V_B$) low stage as the interior of the chamber gets filled with a mixture of $SF_6$ that is not liquefacted and remaining air that cannot be ventilated. The ability of $LSF_6$ insulation is higher than the high-pressurized $SF_6$ gas. The breakdown characteristics of $LSF_6$ were produced by bubble formed evaporation of $LSF_6$ and bubbles caused by high electric emission. It is considered in this paper that the results are fundamental data for electric insulation design of superconductor and cryogenic equipments machinery that will be studied and developed in the future.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.223-224
• /
• 2005

In this paper, multiple regression analysis of the electrical characteristics for $HfO_2$ thin films grown by metal organic molecular beam epitaxy (MOMBE) was investigated. The electrical properties, such as, the accumulation capacitance and the hysteresis index, are the main factors to determine the characteristics of $HfO_2$ thin films. The input factors on the process are the substrate temperature, Ar gas flow, and $O_2$ gas flow. For statistical analysis, the design of experiments was carried out and the effect plots were used to analyze the manufacturing process. This methodology can predict the electrical characteristics of the thin film growth mechanism related to the process conditions.

• Journal of the Korean institute of surface engineering
• /
• v.52 no.2
• /
• pp.72-77
• /
• 2019

To study the characteristics of AC driven OLED, we fabricated the fluorescent OLEDs and analyzed the electroluminescence characteristics of OLEDs with AC negative voltage. The luminance and the current density of the OLED decreased, and the number and size of the dark spots increased in proportion to the duration time and level of the applied AC negative voltage. The current efficiency of the OLED was improved when high AC negative voltage was applied within a short time. When the AC negative voltage of 10 V was applied for 1 minute, the efficiency was improved by 12.4%. Also, the degradation of luminance and current efficiency due to the duration of light emission was improved in the case of OLED applied for 1 minute with 10 V AC negative voltage. These are expected as a result of the improvement of the leakage current characteristics by eliminating the short-circuit region formed by the defect of the OLED at the AC negative high voltage. As a result, the continuous application of AC negative voltage reduced the luminance and the current density of OLED, but the temporary application of AC negative voltage with the proper time and voltage could improve the efficiency and lifetime of OLED.

• Geomechanics and Engineering
• /
• v.18 no.4
• /
• pp.417-426
• /
• 2019

Gangue filling in the goaf is an effective measure to control the surface subsidence. However, due to the obvious deformation of gangue compression, the filling effect deserves to be further studied. To this end, the deformation of coal gangue filling in the goaf is analyzed by theoretical analysis, large-scale crushed rock compression test, and field investigation. Through the compression test of crushed rock, the deformation behaviour characteristics and energy dissipation characteristics is obtained and analysed. The influencing factors of gangue filling and predicted amount of main deformation are summarized. Besides, the predicted equation and filling subsidence coefficients of gangue are obtained. The gangue filling effect was monitored by the movement observation of surface rock. Gangue filling can support the roof of the goaf, effectively control the surface subsidence with little influence on the ground villages. The premeter and equations of the main deformation in the gangue filling are verified, and the subsidence coefficient is further reduced by adding cemented material or fine sand. This paper provides a practical and theoretical reference for further development of gangue filling.