• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.9-10
• /
• 2005

A study on the combustion and exhaust emissions characteristics by using Emulsion Fuel in Diesel Engine is performed experimentally. In this paper, the experiments are performed at engine speed 1800rpm, emulsion fuel ratio is 0%, 5%, 10%, 15%, 20%, 25%, and main measured items are specific fuel consumption, NOx and Soot emissions etc. The obtained conclusions are as follows. 1) Specific fuel consumption increase maximum 19.8% at low load, but is not effected at full load. 2) NOx emissions decrease 30% in case of emulsion fuel ratio 25% at full load. 3) Soot emission decrease 58.9% in case of emulsion fuel ratio 25% at full load.

• 한국분무공학회지
• /
• 제22권4호
• /
• pp.197-202
• /
• 2017

The objective of this study is to investigate the effects of low-temperature combustion (LTC) on the correlations of combustion characteristics and reduction of exhaust emissions in a small DI diesel engine with biodiesel fuel. In order to analyze the combustion, exhaust emission characteristics and distribution of nano size particles for biodiesel were investigated. In addition, to evaluate the effect of LTC on the combustion and emission characteristics, 30 and 50% of cooled-EGR rates were investigated. From these results, it revealed that the influence of LTC on the combustion characteristics showed that the ignition delay significantly increased and reduces peak heat release rate of premixed combustion by lowering reaction rate. With 50% EGR and advanced injection timing, soot and $NO_x$ emissions were simultaneously reduced.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2001년도 제17회 학술발표회 논문초록집
• /
• pp.61-67
• /
• 2001

Hybrid propulsion systems provide many advantages in terms of stable operation and safety. However, classical hybrid rocket motors have lower fuel regression rate and combustion efficiency compared to solid propellant rocket motor. The recent research efforts are focused on the improvement of volume limitation and regression rate in the hybrid rocket engine. The present study has numerically investigated the combustion processes in the hybrid rocket engine. The turbulent combustion is represented by the eddy breakup model and Hiroyasu and Nagle and Strickland-Constable model are used for soot formation and soot oxidation. Radiative heat transfer is modeled by finite volume method. To reduce the uncertainties for convective heat transfer near solid fuel surface having strong blowing effect, the Low Reynolds number k-$\varepsilon$ turbulent model is employed. Based on numerical results, the detailed discussion has been made for the turbulent combustion processes in the vortex hybrid rocket engine.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권1호
• /
• pp.37-45
• /
• 2010

본 논문에서는 박용 디젤엔진에서 NOx와 Soot의 배출량을 동시에 줄이기 위해 파일럿 분사의 특성을 알아보기 위해서 수치해석을 수행하였다. 수치해석결과의 압력 선도는 실험 결과와 일치시켜 1.6% 범위의 적은 오차에서 예측함으로써 수치해석의 신뢰성을 검증하였고 총 분사량이 고정된 상태에서 분사시기, 분사휴지 기간, 분사율을 주요 파라미터로 적용하였다. 파일럿 분사시기의 변화는 연료의 자발화와 열발생률에 영향을 주는 것을 결과로부터 알 수 있었다. 결과로부터 분사휴지기간이 $10^{\circ}$CA, 분사율이 0.022kg/s인 경우에 실린더의 압력 손실이 없는 범위에서 NOx와 Soot를 동시에 저감하는 결과를 얻을 수 있었다.

• 한국산학기술학회논문지
• /
• 제15권6호
• /
• pp.3383-3388
• /
• 2014

본 연구는 4실린더 커먼레일 디젤 기관에서 바이오디젤 혼합 연료와 순수한 디젤연료를 사용하여 EGR율을 변화시켰을 때 연소 및 배기 특성을 디젤 연료만을 사용하였을 경우와 비교하기 위하여 실험을 수행하였다. 본 연구에서는 일반적으로 많이 사용되고 있는 기관 회전 속도 2,000rpm에서 바이오디젤 혼합율 20%의 연료와 디젤 연료를 사용하여, EGR율에 다양하게 변화를 주어 실험을 하였다. 실험결과, 연소압력은 바이오디젤 혼합 연료와 디젤 연료 모두 EGR율이 증가할수록 감소하였으며, 도시 평균유효 압력은, 디젤 연료에 비하여 바이오디젤 혼합 연료가 더 높게 나타났다. 배출가스의 경우에, NOx는 EGR율이 증가할수록 디젤 연료에 비하여 바이오디젤 혼합 연료가 더 많이 배출되었다. 또한 NOx는 바이오디젤 혼합 연료와 디젤연료 모두 EGR율이 증가할수록 감소되었다. CO와 Soot, $CO_2$는 EGR율이 증가 할수록 증가하였으며, CO, Soot은 디젤 연료에 비해 바이오디젤 혼합 연료에서 더 작게 배출되었지만 $CO_2$는 더 많이 배출되었다.

• 한국자동차공학회논문집
• /
• 제5권3호
• /
• pp.54-65
• /
• 1997

To quantify the LII signals from soot particle of flames in diesel engine cylinder, a new method has been proposed for correcting LII signal attenuated by soot particles between the measuring point and the detector. It has been verified by an experiment on a laminar jet ethylene-air diffusion flame. Being proportional to the attenuation, the ratio of LII signal at two different detection wavelengths can be used to correct the measured LIIsignal and obtain the unattenuated LII signal, from which the soot volume fraction in the flame can be estimated. Both the 1064-nm and frequency-doubled 532-nm beams from the Nd : YAG laser are used. Single-shot, one-dimensional(1-D) line images are recorded on the intensified CCD camera, with the rectangular-profile laser beam using 1-mm-diameter pinhole. Two broadband optical interference filters having the center wavelengths of 647 nm and 400 nm respectively and a bandwidth of 10 nm are used. This two-wavelength correction has been applied to the ethylene-air coannular laminar diffusion flame, previously studied on soot formation by the laser extinction method in this laboratory. The results by the LII measurement technique and the conventional laser extinction method at the height of 40 nm above the jet exit agreed well with each other except around outside of the peaks of soot concentration, where the soot concentration was relatively high and resulting attenuation of the LII signal was large. The radial profile shape of soot concentration was not changed a lot, but the absolute value of the soot volume fraction around outside edge changed from 4ppm to 6.5 ppm at r=2.8mm after correction. This means that the attenuation of LII signal was approximately 40% at this point, which is higher than the average attenuation rate of this flame, 10~15%.

• Journal of Mechanical Science and Technology
• /
• 제16권6호
• /
• pp.851-860
• /
• 2002

In this study, it was attempted to obtain the fundamental data for the formation and oxidation of soot from a diesel engine. Combustion of spray injected into a cylinder is complex phenomenon having physical and chemical processes, and these processes affect each other. There are many factors in the mechanism of the formation and oxidization of soot and it is necessary to observe spray combustion microscopically. In order to observe with that view, free fuel droplet array was used as an experimental object and the droplet array was injected into an atmospheric combustion chamber with high temperature. Ambient temperature of the combustion chamber, interdroplet spacing, and droplet diameter were selected as parameters, which affect the formation and oxidation of soot. In this study, it was found that the parameters also affect ignition delay of droplet. The ambient temperature especially affected the ignition delay of droplet as well as the flame temperature after self-ignition. As the interdroplet spacing that means the local equivalence ratio in a combustion chamber was narrow, formation of soot was increased. As diameter of droplet was large, surface area of the droplet was also broad, and hence evaporation of the droplet was more active than that of a droplet with relative small diameter.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 1998년도 제17회 KOSCI SYMPOSIUM 논문집
• /
• pp.103-110
• /
• 1998

This experiment is performed to investigate the effects of the emulsion on the flame temperature and soot formation in a diesel engine. The two-color method is used to measure the flame temperature for combustion of emulsified diesel in the Rapid Compression and Expansion Machine(RCEM). The concentration of soot is estimated via calculation of the KL factor. The solenoid valve, elecronic controller and needle lift sensor are used to control the exact injection timing and duration under various operating conditions. According to the results the soot concentration is reduced with the increasing W/O while the temperature reduced. The pressure data and the flame images captured by a high speed camera show that the ignition delay of emulsified diesel increase the duration of premixed combustion. The sizes of water drops are measured to be about 10${\mu}m$ by a microscope.

• 대한기계학회논문집A
• /
• 제39권12호
• /
• pp.1199-1206
• /
• 2015

본 연구는 경유와 바이오디젤(대두유) 혼합연료의 디젤엔진 배기특성을 조사하였고, 연료 혼합비는 BD(biodiesel)3, BD5, BD20, BD50 및 BD100이며, 분사압력 조건을 400 bar, 600 bar, 800 bar, 1000 bar 및 1200 bar로 변화시켰다. 그리고 연료 혼합비 및 분사압력에 따른 엔진배출물인 NOx와 Soot의 정량적인 분석을 위해 통계학에 기초한 피어슨 상관계수와 스피어만 상관계수를 이하였다. 본 연구의 결과로서 실험변수인 혼합비와 분사압력에 대한 NOx 및 Soot 발생량의 피어슨 상관계수는 -0.811이며, 스피어만 상관계수는 -0.884로 NOx와 Soot 발생량 관계가 선형적이며, 이것은 trade-off관계를 나타낸다. 또한 각각의 분사압력 조건에서 피어슨 상관계수가 음의 상관 관계를 나타내며 이것은 NOx와 Soot 배출관계가 반비례적인 것을 나타낸다.

• Journal of Mechanical Science and Technology
• /
• 제20권9호
• /
• pp.1436-1448
• /
• 2006

This paper describes the effects of injection rate shaping on the combustion, fuel consumption and emission of $NO_x$ and soot of a medium duty diesel engine. The focus is on the influence of four different injection rate shapes, square type 1, square type 2, boot and ramp, with a variation of maximum injection pressure and start of injection (SOI). The experiments were carried out on a 1 liter single cylinder research diesel engine equipped with an amplifier-piston common rail injection system, allowing the adjustment of the injection pressure during the injection event and thus injection rate as desired. Two strategies to maintain the injected fuel mass constant were followed. One where rate shaping is applied at constant injection duration with different peak injection pressure and one strategy where rate shaping is applied at a constant peak injection pressure, but with variable injection duration. Injection rate shaping was found to have a large effect on the premixed and diffusion combustion, a significant influence on $NO_x$ emissions and depending on the followed strategy, moderate or no influence on soot emission. Only small effects on indicated fuel consumption were found.