• 한국의류학회지
• /
• 제27권1호
• /
• pp.123-133
• /
• 2003

The specific objectives of the study were as follows: 1) To investigate the composition system (design, usability and interactivity) of web sites of textile exchange of B to B 2) To examine and valuate contents and marketing (announcement, satisfaction and variety of contents) of web sites of textile exchange of B to B. The data were collected from search engine, portal sites of evaluation, direct contact, interview over the phone with web master of concerned web sites and the result of analytical valuation of web sites. The results of this study were as fellows: 1) The Dongsung trading intended to mainly use their homepage as a inside communication place by intranet network. The Daechang trading was mainly using their homepage as a tool of expansion of their outside export market. The etextiler was selling their web solutions through homepage. The texcom was offering the web place and useful informations to trading companies in Asia. 2) The texcom consisted text with little image to speed up for loading and navigation for usability of users. The Dongsung trading made intranet network for communication and exchange of informations of company inside. The etextiler offered a booking menu to inquiry in homepage. The Daechang trading tried to give good impression from the introduction page at homepage.

• 한국자동차공학회논문집
• /
• 제7권8호
• /
• pp.34-42
• /
• 1999

In late 1997, the portion of registered light-duty diesel vehicle was 25.3% and its emission rate was 17.1% in Korea. Especially, diesel particulate matters(DPM) and NOx are hazardous air pollutants to human health and environment in urban area. The reduction technologies of exhaust emissions from diesel engines are improvement of engine combustion, fuel quality and development of diesel exhaust after treatment , In this study , a light-duty diesel oxidation catalyst(DOC) that is one of the diesel exhaust after treatment was made for performance evaluation and the emission characteristics were tested on CVS-75 mode. And the analysis of the particle size distribution with scanning mobility particle 100, 67.6% and 66.7, 10.0% for Pt and Pt-V catalyst .And for Pt catalyst, the PM increased 7.8% because of increasing sulfate but Pt-V catalyst reduced the PM to 23.0% . Test results of particle size distribution showed that peak values of number and mass densities are respectively 100∼200nm their distribution trend independent of vehicle speed.

• 한국자동차공학회논문집
• /
• 제8권5호
• /
• pp.20-27
• /
• 2000

Characteristics of two favorite injection tools for gasoline direct injection application were compared. An air-assisted fuel injector (AAFI) and a high-pressure swirl injector (HPSI) were designed and fabricated for prototype development, and the characterization strategies and processes for both injection tool have been arranged in parallel. Characterization works were carried out mainly through measurements, and in some cases, computational fluid dynamic analysis was utilized. In this paper, overall characteristics defined as flow rate, spray pattern, penetration, internal spray structure and drop size distribution, was discussed. The AAFI was found to be advantageous in flexibility of fuel flow rate, and the HPSI in stability and precision. Spray shape factor was introduced to describe the development of intermittent sprays from both injectors. Axial penetration appeared to be almost linear in the case of the AAFI while its speed continuously decreased with time in the HPSI.

• 한국자동차공학회논문집
• /
• 제18권4호
• /
• pp.1-7
• /
• 2010

Large quantity of bending deformation as well as irregular rotating torque fluctuation are the main struggles of the balance shaft module during a high speed rotation. Since two issues are much sensitive to the location of both supporting bearing and unbalance mass at a balance shaft, it is recommended to construct a design strategy on balance shaft at the early stage so as to save developing time and effort before approaches to the detailed design process. In this paper, an optimal design formulation is proposed to minimize the elastic strain energy due to bending as well as the kinematic energy of polar moment of inertia in rotation. Case studies of optimal design are conducted for different mass ratio as well as linear combination of objective function and its consequence reveals that global optimum of balance shaft model is existed over possible design conditions. Simulation shows that best locations of both supporting bearing and unbalance are globally 20% and 80%, respectively, over total length of a balance shaft.

• Journal of Biosystems Engineering
• /
• 제40권2호
• /
• pp.95-101
• /
• 2015

Purpose: During the start-up period, the response time of a hydraulic system increases in the winter because of the increased oil viscosity caused by the cold weather. The problems of delayed tractor starting and excessive wear of the clutch disk occur for these reasons. Therefore, this study develops an analysis model using the commercial hydraulic analysis program AMESim to examine the characteristics of delays in power shuttle starting at different oil temperatures. Methods: In the experiment, a tractor was stationary on a flat surface with the engine running at a constant speed of 1,080 rpm. The forward lever was then pressed to activate the power shuttle at three different oil temperatures, and the pressure changes were measured. The pressure on the forward clutch control valve was measured by a pressure gauge installed on the hydraulic line supplied to the transmission from the main valve. An analysis model was also developed and verified with actual tests. Results: The trend of the simulated pressures of the power shuttle is similar to that of the measured pressures, and a constant modulation period was observed in both the simulation and test results. However, the difference found between the simulation and test results was the initial pressure required to overcome the initial force of the clutch spring. Conclusions: This study also examines the characteristics of the delayed startup of the power shuttle at different oil temperatures through simulations.

• 한국자동차공학회논문집
• /
• 제21권5호
• /
• pp.34-39
• /
• 2013

The gear shifting timing of a manual transmission vehicle is influencing fuel economy. This paper focuses on an gear shifting indicator of an city bus with manual transmission, which can improve fuel economy. The shift indicator is supposed to collect the vehicle data during driving, calculate and compare fuel economy with and without gear shifting, and indicate the proper gear shifting timing. The H/W and S/W of the shift indicator are developed and tested on city bus in this research. The experiments are carried out on real road by 3 different drivers and the results show the improvement of fuel economy from 6.0% to 21.4%. The average engine torque and speed are reduced due to early gear shifting and the usage of highest gear is increased. The results of chassis test are also performed and show 7.5% improvement of fuel economy.

• 전력전자학회논문지
• /
• 제23권1호
• /
• pp.47-58
• /
• 2018

A solar array simulator (SAS) consists of an engine that generates a setpoint according to panel characteristics, a power stage that provides the actual output, and a controller. Particularly, if the control method is not suitable due to the nonlinearity of the solar panel output curve depending on the irradiation amount and the temperature, and the variation of the curve factor depending on the various panel materials, then the panel simulation function cannot be performed properly. Current and voltage mode controls are usually used for the conventional control method. However, these control methods deteriorate the control performance near the maximum power point; thus, a hybrid control method using two or more controllers has been investigated. In this study, we analyze the hybrid control method using three controllers divided into different areas. The design equation of the controller is derived based on the small signal modeling of each controller, and the simulation performance of the solar array simulator verifies its stability and response speed.

• 한국분무공학회지
• /
• 제2권2호
• /
• pp.8-15
• /
• 1997

Combustion chamber systems using spray impinged on walls have been studied for improving combustion characteristics in high speed direct injection diesel engines. The fuel spray injected in a small combustion chamber may be easily impinged and deposited on the wall. The fuel deposit has been considered as the cause for unburned emission due to difficulty of fuel-air mixing. In this paper w-shaped combustion chamber which has four raised pips on the side wall is introduced and discussed by comparing with conventional chamber with no pips. The computer code employing new spray-wall interaction model in general non-orthogonal grids is used in here. The model is applied into the new chamber shape with raised pips. In this chamber system four-hole nozzle is used, and the sprays injected from the each hole impact on lands raised from the chamber wall surface. After impacting, the sprays break up into much smaller drops and distribute over all the chamber space, instead of distributing just near the wall surface in conventional omega-shape. The results showed the potential of the w-shaped chamber employing pips for dispersing droplets so as tn avoid the fuel deposit regions.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제28회 춘계학술대회논문집
• /
• pp.245-249
• /
• 2007

본 연구에서는 모델 기반(Model-Based) 성능진단에 신경회로망을 적용하였고, SIMULINK를 이용하여 PW206C 터보축 엔진의 모델링을 수행하였다. 비행 고도, 비행 마하수, 가스발생기 회전수에 따른 다양한 운용영역의 성능데이터를 base로 하여 압축기, 압축기터빈, 동력터빈의 성능 저하에 대한 학습 데이터를 획득하고 역전파(Back Propagation Network)를 이용하여 훈련 하였다. 설계점 및 탈설계 영역에서 압축기, 압축기터빈, 동력터빈의 단일 손상 탐지를 수행한 결과 손상된 구성품을 잘 탐지함을 확인할 수 있었다.

• 한국추진공학회지
• /
• 제18권4호
• /
• pp.50-60
• /
• 2014

초공동현상을 이용한 고속 수중 운동체와 함께 이를 가능하게 하는 기술로써 해수흡입 램젯 추진에 대한 연구가 여러 나라에서 진행되고 있다. 본 연구에서는 해수 흡입 램젯 엔진을 추진기관으로 하는 수중 운동체의 개념 설계를 진행하였다. 가동 환경을 확인하여 임무 작동 조건을 설정하였으며, 해당 조건 내에서 초공동현상 이론과 유체역학적 지식을 통해 운동체에 작용하는 항력을 예측하였다. 이로부터 필요 추력을 산출하여 추진기관의 대략적인 사이징과 부분별 성능해석을 수행하였으며, 설계한 추진기관의 추력 및 비추력 성능을 확인하였다.