• 한국대기환경학회지
• /
• 제7권1호
• /
• pp.31-40
• /
• 1991

This study shows the correlation between $NO_x$ emission in the exhaust gas and various operation factors of dual fuel engine for Co-generation system. General tendency was shown that the thermal efficiency was lowered by the change of operation factors. However these were not confirmed on this experiment. Increasing T4 temperature (exhaust gas temperature at turbo-charger inlet) reduces $NO_x$ emission rate. The higher T4 temperature requires lower excess air as the excess air ratio is controlled by T4 temperature on gas mode operation. Another tendency was that $NO_x$ emission rate is reduced in case of increasing boost air temperature, quantity of pilot oil or bypassing flue gas through the exhaust gas boiler. The diameter of the fuel injection nozzle was changed smaller than design value and the injection timing was readjusted. Thus $NO_x$ emission rate could be reduced as retarding injection timing and changing hole diameter of fuel injection nozzle, however maxium engine out-put was decreased by changing fuel nozzle on the diesel mode operation.

• 해양환경안전학회지
• /
• 제24권6호
• /
• pp.834-840
• /
• 2018

본 연구에서는 선박용 엔진을 활용하여 E2, E3 사이클 시험 결과로부터 연료 내 황 함유량 변화에 따른 대기오염물질 배출 특성을 조사하였다. 테스트를 위해 사용된 엔진은 360 PS의 엔진(Doosan L126TIH engine)을 활용하였고, 동력계로는 Horiba-Schenck사의 400급 동력계인 W400을 사용하였다. 엔진에서 발생되는 대기오염물질 계측을 위해서는 오스트리아 AVL사의 FTIR과 SPC 장비를 배기라인 후단에 장착해서 사용하였다. 실험 결과로는 E2, E3 사이클 모두에서 연료 내 황 함유량이 증가할수록 THC와 CO의 단위 출력 당 배출량은 감소하고 입자상물질은 증가하였다. 연료의 황 함유량이 증가할수록 동점도가 증가되어 엔진의 연료소모율이 좋아지는 것을 확인하였다. 이는 본 연구에 사용된 엔진의 경우 연료 분사압력이 일정한 상태에서 동점도 증가에 따른 분무입자의 평균입경이 커짐에 따른 연소상태가 개선되었기 때문이라 생각되어진다. 질소산화물의 경우 이번 연구에서는 황함유량의 변화에도 배출량에서는 큰 변화를 보이지 않았다.

• Tribology and Lubricants
• /
• 제30권1호
• /
• pp.21-28
• /
• 2014

Damage to the cylinder liner of large ship engines, such as scuffing on the surface, can occur very easily because it is operated in a corrosive environment. This scuffing may be due to oil film destruction and corrosive wear caused by water and sulfur included in the fuel, abrasive impurities, and poor lubricants. Thus, a method for monitoring the condition and diagnosing the failure of the cylinder liner and piston ring is needed. In this study, a reciprocating friction and wear test was carried out with a cast iron specimen, which simulated an engine cylinder in a corrosive atmosphere. The lubricants used were base oil, stirred oil with distilled water, a NaCl solution, and dilute sulfuric acid. The friction coefficient and frequency spectrum were measured using a load cell and acceleration sense in each experimental condition. We then used these results to diagnose the failure of the cylinder liner.

• 한국산학기술학회논문지
• /
• 제10권11호
• /
• pp.3048-3053
• /
• 2009

소형엔진은 매우 열악한 환경에서 작동하기 때문에 엔진으로 흡입되는 공기를 정화하는 흡기시스템은 매우 중요한 설계인자이다. 크랭크 실로부터 유입되는 블로바이 가스의 오일입자를 포집하기 위하여 장착되는 그리드는 제작과 장착이 어렵고 오일입자의 포집효율이 열악한 문제점이 있다. 본 연구는 이러한 소형엔진에 적용되는 흡기시스템을 개선하기 위하여 신규 모델을 해석적인 방법으로 개발하였다. 신규로 제안된 모델은 그리드를 삭제하고 블로바이홀의 위치를 변경하였다. 신규 모델의 오일입자 포집효율은 기존 대비 약 5배 향상되었으며, 그리드 삭제로 인하여 소형엔진 흡기시스템 제작 원가의 약 10%를 절감하였다.

• Corrosion Science and Technology
• /
• 제14권2호
• /
• pp.54-58
• /
• 2015

A heavy oil of low quality has been mainly used in the diesel engine of the merchant ship as the oil price has been significantly jumped for several years. Thus, a combustion chamber of the engine has been often exposed to severely corrosive environment more and more because temperature of the exhaust gas of the combustion chamber has been getting higher and higher with increasing of using the heavy oil of low quality. As a result, wear and corrosion of the engine parts such as exhaust valve, piston crown and cylinder head surrounded with combustion chamber are more serious compared to the other parts of the engine. Therefore, an optimum repair welding for these engine parts is very important to prolong their lifetime in a economical point of view. In this study, 1.25Cr-0.5Mo filler metal was welded with SMAW method in the forged steel which would be generally used with piston crown material. And the corrosion properties of weld metal, heat affected and base metal zones were investigated using electrochemical methods such as measurement of corrosion potential, anodic polarization curves, cyclic voltammogram and impedance etc. in 35% $H_2SO_4$ solution. The weld metal and base metal zones exhibited the highest and lowest values of hardness respectively. And, the corrosion resistance of the heat affected and weld metal zones was also increased than that of the base metal zone. Furthermore, it appeared that the corrosive products with red color and local corrosion like as a pitting corrosion were more frequently observed on the surface of the base metal zone compared to the heat affected and weld metal zones. Consequently, it is suggested that the mechanical and corrosion characteristics of the piston crown can be predominantly improved by repair welding method using the 1.25Cr-0.5Mo electrode.

• 선박안전
• /
• 통권35호
• /
• pp.2-18
• /
• 2013

국내 원동기 배출허용기준 및 연료유 기준을 미국 및 유럽 등과 같이 일원화된 관리를 하기 위하여 대기환경보전법 개정이 되었다. 이에 따라 하위 법령 및 세부기준을 마련하기 위하여 국내외 관련 기준을 조사하고, 노후 선박용 원동기 시험을 진행하며, 선박 원동기 배출량을 산정하여 선박 원동기 배출허용기준(안)을 수립하고 기준 적용에 따른 규제 비용 및 편익 분석을 수행하였다.

• 해양환경안전학회지
• /
• 제19권1호
• /
• pp.52-58
• /
• 2013

선박의 운항에 소요되는 운항비는 선박의 종류, 크기, 속력, 항행구역 등에 따라 다를 수 있지만, 연료비가 차지하는 비율은 50~60 %에 달하는 것으로 알려져 있다. 최근 국제 유가의 상승으로 인한 선박 운용비를 절감하기 위하여 중소형 선박에서도 저질연료유의 사용이 검토되고 있는 추세이다. 더 나아가 해운선사들은 연료소모량을 줄이기 위한 방법으로 감속운항을 취하고 있다. 따라서, 본 연구에서는 실선을 이용하여 해상에서의 선속대비 주기관의 연료소모량을 계측하고, 부하에 따른 전진계수 대비 속력과 연료소모량의 관계를 통해 상용연속출력보다 낮은 주기관 부하의 70 % 영역이 최적의 운항조건이라고 제안하였다.

• 한국자동차공학회논문집
• /
• 제16권5호
• /
• pp.147-156
• /
• 2008

As the management of fuel efficiency becomes globally reinforced in attempts to find an environment-friendly vehicle that will operate against global warming, the interest in and the demand for the type of vehicle with a high-efficiency diesel engine using light oil. However, it also emits a greater amount of PM (particulate matter) and NOx than emissions from vehicles using other types of fuels. Therefore, the DME (Dimethyl Ether), an oxygen containing fuel draws attention as an alternative fuel for light oil that can be used for diesel engines since it generates very little smoke. But to develop and compare performance of an electric controlled common-rail DME engine, engine tests requires optimized injection conditions at required engine RPM and engine torque. These injection conditions cannot be set freely and the data configuration through the experimentally repeated application requires much time as well as a significant amount of errors and effort. The object of this study is to configure the basic injection map using the results of the DME engine experiments performed so far. For this, in this study, the functionalization of the required equations were performed along with the basic review of the factors that had influence on the data map. Through this, the information on the injection pressure, injection amount, injection duration, injection timing, etc. under certain operation condition could be obtained.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2004년도 총회 및 춘계학술발표회
• /
• pp.297-300
• /
• 2004

The various microbial tests were performed to determine bioremediation agent capacity for eight strains isolated from the oil contaminated regions. Two tests for isolated strains were conducted such as cell hydrophobicity and emulsifying activity. The biodegradation of SHM (saturated hydrocarbon mixture) and AHM (aromatic hydrocarbon mixture) with the strains also was carried out. The strains having higher cell hydrophobicity and emulsifying activity degraded petroleum oil effectively. The degradation capacity for SHM was represented more than 90% in YS-7 and WLH-1 of isolated strains, and KH3-2 were capable of degrading AHM. Especially, WLH-1 as yeast was shown more than two or three times in the degradation capacity of automobile engine lubricants and the biomonitoring results of contaminated soil for residual oil degrading test showed that the hydrocarbon biodegradation was increased in the second treatment by this strain.

• 한국대기환경학회지
• /
• 제31권4호
• /
• pp.368-377
• /
• 2015

Bunker C fuel oil is a high-viscosity oil obtained from petroleum distillation as a residue. The sulfur content of bunker C fuel oil is limited to 4.0% or even lower to protect the environment. Because bunker C fuel oil is burned in a furnace or boiler for the generation of heat or used in an engine for the generation of power, carbon dioxide is emitted as a result of combustion. The objective of this study is to investigate $CO_2$ emission characteristics of bunker C fuel oil by sulfur contents. Calorific values and carbon contents of the fuels were measured using the oxygen bomb calorimeter method and the CHN elemental analysis method, respectively. Sulfur and hydrogen contents, which were used to calculate the net calorific value, were also measured and then net calorific values and $CO_2$ emission factors were determined. The results showed that hydrogen content increases and carbon content decreases by reducing sulfur contents for bunker C fuel oil with sulfur contents less than 1.0%. For sulfur contents between 1.0% and 4.0%, carbon content increases as sulfur content decreases but there is no evident variation in hydrogen content. Net calorific value increases by reducing sulfur contents. $CO_2$ emission factor, which is calculated by dividing carbon content by net calorific value, decreases as sulfur content decreases for bunker C fuel oil with sulfur contents less than 1.0% but it showed relatively constant values for sulfur contents between 1.0% and 4.0%.